The GENERAL PUMP TH3020G , 3.0 GPM @ 2000 PSI @ 3600 RPM Features:
Extended-life design for light commercial duty use
Heavy duty die-cast aluminum housing
Integrated flow sensing unloader, to avoid the liability of having a pressurized hose after the engine is shut off
Integrated mounting manifold for efficient power transmission and heat dissipation
Triplex plunger design for smooth operation
Fixed chemical injector
Forged brass manifold
The GENERAL PUMP TH3020G , 3.0 GPM @ 2000 PSI @ 3600 RPM has the following specifications:
Maximum Volume: 3.0 GPM
Maximum Discharge Pressure: 2000 PSI
Maximum Pump Speed: 3600 RPM
Inlet Pressure 1 – 100 PSI
Bore: .591 in. / 15 mm
Stroke: .254 in / 6.46 mm
Crankcase oil Capacity: 6.75 oz.
Maximum Fluid Temperature: 140 F
Inlet Port Thread: 1/2″ NPT-M
Discharge Port Thread: 3/8″ – 19 BSPP-M
Shaft Diameter 3/4″
Weight: 9.25 lbs
Dimensions: 7.5″ x 7.0″ x 9.0″
GENERAL PUMP TH3020G
List Price: $517.30 Our Price: $398.06 Click for more info. Replacement Pump Comet BXD2528 You save $119.24! Availability:: available for order Product Code: TH3020G ( GENERAL PUMP TH3020G )
GENERAL Pressure Washer Pump
PRICE SUBJECT TO CHANGE. PRICE VALID 10/25/2011
List Price: $565.84 Our Price: $424.06 You save $141.78! Availability:: available for order Product Code: LAN-8.702-383.0 (CAT PUMP 1LX100)
PRICE SUBJECT TO CHANGE. PRICE VALID 10/25/2011
INSTALLATION ON THIS CAT PUMP 1LX100:
Each CAT PUMP 1LX100 comes with oil in the crankcase ready for start-up. CAT PUMPS special premium grade, multi-viscosity crankcase oil should be used. It is recommended to install this pump in a horizontal position with the oil filler cap at the top. It is permissible to rotate the oil filler cap to the right or left, however, some oil spitting may occur. A rubber plug is inserted into the oil filler cap for shipping. This should be removed before operation. Do not operate pump with plug in cap. Flexible hose should be installed at the unloader ports. Connect a hose equal to or one size larger than the inlet port at the bottom of the pump body. Connect a high pressure hose to the regulator discharge port at the side of the regulator. Connect a by-pass hose to the bottom port of the regulator or unloader and run to drain or back to a “T” in the inlet line. CAUTION: Do not over tighten the RTP pump or regulator body.
OPERATION of the CAT PUMP 1LX100:
Once the inlet water supply is turned on and the pump is started, adjust the regulator at the top with an allen wrench or turn adjusting cap on the unloader to set system pressure. Do this in small increments until the desired system operating pressure is reached. The CAT PUMP 1LX100 are axial plunger pumps. Special direct-drive motors are secured to the pump with a V-Clamp Mounting. The optional Drive Mount Assembly is required for the belt drive 1LXB100 model. The motor on the CAT PUMP 1LX100 rotates the offset cam and guide plate which is connected to the three plungers. Each plunger moves forward at a different stage of the cam rotation, providing a smooth, forward, liquid flow through the pump. On the back stroke, the liquid enters the inlet chamber and flows through each inlet valve. As the forward stroke begins, the inlet valve closes. On the forward stroke, the liquid goes through the seat and forces the discharge valve open to allow the liquid out the regulator discharge port.
The MH-0300-0MIH Frame: Powder coated steel frame, handle and tank · Heavy-duty tires for easy mobility · Front foot brace · Rugged steel body
This MH-0300-0MIH Burner has: Stainless-steel combustion chamber · Direct spark ignition
The MH-0300-0MIH Motor: Heavy-duty, high quality cast aluminum electric motor
The MH-0300-0MIH has the following Components: Safety switch prevents overheating · Thermostatically controlled · Suitable for air ducting · Easy to operate controls · High capacity fuel tank · Electronic flame control · Automatic ignition · Water resistant control box · Automatic fuel shut-off · High thermal efficiency · Control panel with thermostat plug, reset push button and safety air pressure switch · High pressure fuel pump · Vacuum sensor helps prevent heater lock out · Heated fuel filter for more reliable starts in subzero temperatures
The MH-0300-0MIH Functions on: Kerosene or No. 1 and No. 2 fuel oil.
The MH-0300-0MIH is best used on construction sites and applications where the heat will be ducted into a building.
Specifications subject to change without notice. Use in accordance with any and all state or local codes, regulations, and/or ordinances.
Please see heater “Owner’s Manual” included with each heater for a complete list of important safety information.
Important Notes:
· Not for use in residential living areas or inadequately ventilated areas.
· Proper ventilation required during operation.
· Must be plugged into an approved standard electrical outlet for operation.
BE X-2050FW1COM
Electric Pressure Washer Wall Mount 5HP 2000psi Comet Pump
The BE X-2050FW1COM BE pressure washer is an electric power washer that features a reliable 5 HP BALDOR Electric Motor Engine, to go along with a high quality Comet Triplex BWDK2020E Washer pump. The BE X-2050FW1COM BE pressure washer is the ideal wall mounted pressure washer for property and small business owners, construction workers and handymen where electricity is available.
BE X-2050FW1COM Electric Pressure Washer
The BE X-2050FW1COM Electric Pressure Washer Features:
2000psi PSI Max Pressure. 2.0 GPM Max Flow (7.6LPM)
Powered by an industrial 5HP Baldor electric motor with single phase, 220 volts, and 23 amps.
Auto On/Off Feature. Unit starts automatically when trigger is pulled, & shuts down when trigger is released
Includes quick connect coupler, garden hose inlet, and chemical injector.
Durable powder coated steel frame.
Wall Mounted with Hose Reel
Comet Triplex BWDK2020E Pump
(1) BE X-2050FW1COM Wall Mounted Pressure Washer
(1) 50 ft High Pressure Hose
The BE X-2050FW1COM Electric Pressure Washer has the following specifications:
5 HP BALDOR Electric Motor
PSI 2000
GPM 2.0
Comet Triplex BWDK2020E Pump
List Price: $3,478.00 Our Price: $2,558.00 You save $920.00! Availability:: available for order Product Code: X-2050FW1COM
BE X-2050FW1COM Pressure Washer
PRICE SUBJECT TO CHANGE. PRICE VALID 10/25/2011
LANDA MHP Gasoline-Powered, Hot Water Pressure Washer with a Narrow Frame
■ Up to 3.8 GPM, 3500 PSI
■ Heavy-Duty Honda or Vanguard Engines
■ Belt-Drive Landa Pump with 7-Year Warranty
■ Sch. 80 Heating Coil
LANDA MHP Gasoline-Powered, Hot Water Pressure Washer with a Narrow Frame
The LANDA MHP Gasoline-Powered, Hot Water Pressure Washer with a Narrow Frame Features:
■ Optional, Swivel Hose Reel with compact, easywind design for tangle-free handling of hose (hose reel bracket is standard).
■ Extra-durable Heating Coil made of leak-free, coldrolled, Schedule 80 steel pipe with five-year warranty.
■ Helpful Tri-Lingual Labels with operating instructions in English, Spanish and French for operator and owner liability protection.
■ Unique lift-out design allows for easy and quick Coil Access by removing six bolts.
■ 50 ft. of 3/8″, wire braid Landa Tuff-Flex Hose rated for up to 5000 PSI and featuring a 24-inch Hose Guard for burst protection.
■ High-efficiency 12VDC Burner is mounted on the end for ease of servicing and adjustments.
■ Conveniently located Control Panel with burner on/off switch, monitor light and hour meter for maintenance monitoring.
■ Swivel Crimp Fitting for ease in attaching hose to trigger gun.
▲ Rugged High-Pressure Landa Pump, with three ceramic plungers, forged brass head and 7-year warranty, is connected to the engine by a belt-drive assembly that features cast-iron bushing Pulleys and two notched “V” cogged belts, which provide a cooler operation and longer life; also Two-Bolt Adjustment makes it easy to adjust the belt tension.
■ Industrial-duty Gasoline-Powered Honda or Vanguard engine with overhead valves and easy-access oil drain line; all LANDA MHP have keyed Electric Start.
■ Rugged, 11/4-inch square tube Narrow Frame is only 25- inches in width to fit most doorways and is protected by an all-weather resistant epoxy powder coat finish.
■ Metal Side Panels are easy to remove for convenience in servicing.
■ Many Safety Features, including a rupture disk and thermal pump protector to prevent the build up of excessive pressures or heat.
■ Insulated, spring-loaded Trigger Gun with easy-to-attach Detergent Injector and insulated, dual-lance Variable Pressure Wand make it easy to switch between wash and rinse modes.
■ Two rust-free, 5 gal. Fuel Tanks are “see through” for monitoring fuel levels and have elevated fuel lines to prevent debris from damaging the burner (16 HP model only).
■ Four quick-couple Nozzles are made of hardened stainless steel and are mounted for ready access.
■ Optional Wheel Kit adds portability to the self-contained design.
■ Durable polyurethane Battery Box with vibration isolators for a secure ride.
WHY CHOOSE LANDA’s MHP
The MHP is a self-contained, mini-skid, hot water pressure washer with an extra narrow frame for maneuvering through doorways.
QUALITY: While it is considered an economy model, it is still packed with Landa quality, including reliable Honda or Vanguard engines all with electric start, top-of-the-line, belt-drive, tri-plunger Landa Pump with 7-year warranty, Schedule 80 heating coil made of 1/2-inch cold-rolled pipe, and extrarugged steel frame protected by an epoxy powder coat finish. Moreover, the MHP is assembled in a Landa factory that is certified to the internationally recognized ISO-9001:2000 standards for quality manufacturing.
PORTABILITY: The MHP is easily fitted with an optional wheel kit to make it portable for on-site cleaning. No electricity is needed. Simply provide water and it’s ready to clean most anywhere outdoors. The two five-gallon gasoline and diesel tanks (16HP model only) allow for hours of continuous cleaning. The MHP comes standard with the bracket needed to add an optional hose reel for tangle-free washing and additional high-pressure hose protection.
SAFETY: As with all Landa pressure washers, the MHP comes certified to the rigid UL-1776 safety standards, including: 24-inch hose guard for burst protection; thermal pump protector and unloader for protection against build up of pressure or heat in pump bypass water; and rupture disk to vent any build up of excessive pressure in the heating coil.
MHP Specifications
Part No. GPM PSI Engine CCs(HP) Start Pump RPM BTU’s L x W x H SHIP WT.
MHP4-30324E 3.5 3000 Honda 337(11) Electric 1160 330,000 48″ x 21″ x 42″ 555 lbs.
MHP4-35324E 3.8 3500 Honda 389(13) Electric 1185 350,000 48″ x 21″ x 42″ 595 lbs.
MHP4-35224E 3.8 3500 Vanguard 479(16) Electric 1185 350,000 48″ x 21″ x 42″ 560 lbs.
Note: LANDA is constantly improving and updating their products. Consequently, pictures, features, and specifications may differ slightly from current models. Flow rates and pressure ratings may vary due to variances allowed by manufacturers of their machine components. LANDA attempts to keep their machine performance within ±5% of listed specifications.
OPTIONS for the LANDA MHP Gasoline-Powered, Hot Water Pressure Washer:
Part No. Description
8.903-596.0 Float Tank and Inlet Detergent Metering Valve
8.904-514.0 Pivot Hose Reel, 360° swivel (holds 100 ft. of 3/8″ hose)
8.931-276.0 Stainless Steel Top Wrap with Black Bottom Wrap
8.903-530.0 Stainless Steel Outer Coil Wrap
8.904-533.0 Wheel Kit (4 Caster Wheels)
BE PE-4020HWEBGEN Pressure Washer 20HP Honda 3500psi GX630 Engine
The PE-4020HWEBGEN BE pressure washer is a heavy duty gas power washer that features a reliable 20 HP Honda GX 630 Engine, to go along with a high quality GENERAL TS2021 Washer pump. The PE-4020HWEBGEN BE pressure washer comes complete with everything you need to start cleaning, including a hose, 36″ lance, gun, and tips. This PE-4020HWEBGEN is an industrial pressure washer for property and small business owners, construction workers and handymen.
BE PE-4020HWEBGEN Pressure Washer 20HP Honda 3500psi GX630 Engine
The BE PE-4020HWEBGEN Pressure Washer 20HP Honda 3500psi GX630 Engine Features:
24 Belt Drives
5.6 GPM Axial pump
20 HP Honda GX 630 Engine
Electric start with Oil alert
Steel roll cage frame
Powder coated steel frame
50ft High Pressure Hose
13″ Pneumatic Tires
3500 psi
Brake Mechanism
GENERAL TS2021 Pump
(1) BE PE-4020HWEBGEN Pressure Washer
(1) Lance
(1) Soap Tip
(1) Low pressure chemical injector
(1) 50 ft High Pressure Hose
(1) Spray Gun
The BE PE-4020HWEBGEN Pressure Washer 20HP Honda 3500psi GX630 Engine has the following specifications:
20 HP Honda GX 630 Engine
PSI 4000
GPM 5.3
GENERAL TS2021 Pump
List Price: $4,998.00 Our Price: $3,142.00 You save $1,856.00! Availability:: available for order Product Code: PE-4020HWEBGEN
BE Pressure Washer
PRICE SUBJECT TO CHANGE. PRICE VALID 10/21/2011
Triplex plunger design delivers smoother liquid flow. Hi-Pressure Seals are completely lubricated and cooled by the liquid being pumped. Inlet and discharge valve assemblies interchange for easier maintenance. Lubricated Lo-Pressure Seal provides double protection against external leakage. Oil bath crankcase assures optimum lubrication. Close tolerance concentric of the ceramic plunger maximizes seal life.
The CAT Pump 3CP1130 Ceramic Plunger Pressure Washer Pump Features:
Triplex design offers high efficiency and low pulsation.
Durable high pressure seals are lubricated and cooled by pumped liquid.
Pre-set Lo-Pressure Seals provide secondary protection against external leaks and require no packing adjustment.
Special high-density, polished, concentric plungers provide a true wear surface and extended seal life.
Specially formulated seals offer unmatched performance and extended life.
Optional STHT, FPM and EPDM elastomers for compatibility with many liquids and temperatures up to 200°F.
Convenient press in style seal case and interchangeable inlet and discharge valves for easy servicing
Wet-end easily serviced without entering crankcase.
Pulley Mounting……………………………………Either Side (Either Side)
Shaft Diameter………………………………………………0.650” (16.5 mm)
Weight………………………………………………………14.84 lbs. (6.7 kg)
Dimensions…………………………………..9.1 x 8.78 x 5.47” (231 x 223 x 139 mm)
Flow……………………………………………………………..2.4 gpm (9 lpm)
Pressure Range………………………………100 to 2200 psi (7 to 155 bar)
RPM…………………………………………………………..1725 rpm (1725 rpm)
Stroke………………………………………………………………0.276” (7 mm)
CAT Pump 3CP1130 parts breakdown
3CP1130
Parts Breakdown {click image to left}
Service Manual {Click image to left}
Our Price: $910.00 CALL 1-877-824-7763 FOR A BETTER PRICE! Call 1-877-824-7763 {Smart Phones Click to Call}
Availability:: available for order Product Code: 3CP1130
CAT Pressure Washer Pump
PRICE SUBJECT TO CHANGE. PRICE VALID 10/20/2011
Mi-T-M Portable Heater Kerosene Forced Air – MH-0600-0M10
The MH-0600-0M10 Frame has: Rugged steel body · Extension cord wrap · Powder coated hood and fuel tank · Powder coated steel handles with roll cage design for easy lifting · 13-inch pneumatic tires · Spare parts storage system (located on back of unit) · Fuel drain plug
The MH-0600-0M10 Motors: Heavy-duty, high quality cast aluminum enclosed electric motor
Components for the MH-0600-0M10: Built-in temperature control thermostat with control dial · High performance fan · Power switch · Secured internal components · Integral overheat and flame-out safety · Fuel gauge · Integrated fuel pressure gauge · Oversized fuel cap · High limit temperature shut-off · Sure start ignition for cold temperature starts · Dual connector ignitor · Error indicator read-out
The MH-0600-0M10 is factory tested for multiple fuels: Kerosene, JP8/Jet A fuel, No. 1 or No. 2 fuel oil and No. 1 or No. 2 diesel fuel
This MH-0600-0M10 portable heater is designed for use in workshops, warehouses, garages, construction sites and farms with proper ventilation.
Specifications subject to change without notice. Use in accordance with any and all state or local codes, regulations, and/or ordinances.
Please see heater “Owner’s Manual” included with each heater for a complete list of important safety information.
Important Notes:
· Not for use in residential living areas or inadequately ventilated areas.
· Proper ventilation required during operation.
· Must be plugged into an approved standard electrical outlet for operation.
Mi-T-M Portable Heater Kerosene Forced Air - MH-0600-0M10
The Mi-T-M Portable Heater Kerosene Forced Air – MH-0600-0M10 has the following specifications:
Heat Output 600,000 BTU
Hot-Air Flow 3,000 CFM
Air Pump Pressure 128 PSI
AC Power 120 Volt/60Hz/5.5 Amp
Motor Size 5/8 HP
Fuel Tank Capacity 40.0 gallons
Fuel Consumption 4.5 gal./hr.
Max. Operating Hours 9.0 hours
Heating Area 15,000 sq. ft.
Multi-Fuel Capable Yes
Net Weight 264 lbs.
Shipping Weight 320 lbs.
Length 75 in.
Width 34 in.
Height 43 in.
List Price: $3,150.00 Our Price: $2,677.50 You save $472.50! Availability:: available for order Product Code: MH-0600-0M10
Mi-T-M Portable Heater
PRICE SUBJECT TO CHANGE. PRICE VALID 10/20/2011
The Annovi Reverberi RMW2G24D-PKG – pump package Features:
RMW2G24D – Pump
Max PSI: 2400
Max GPM: 2
RPM: 3400
7/8″ Hollow Shaft
Vertical Gas Engine Flange
TPP140-1/4A – Thermal relief valve
AR1269120 – Detergent tube with filter
List Price: $243.26 Our Price: $156.74 You save $86.52! Availability:: available for order Product Code: RMW2G24-PKG
Annovi Reverberi RMW2G24D-PKG – pump package
PRICE SUBJECT TO CHANGE. PRICE VALID 10/19/2011
This RMW2.2G24-SX-PKG plunger pump will pump up to 2.2 GPM up to 2600 PSI. It spins at 3400 RPM in a direct drive system coupled with a gasoline engine. The matching flange provides convenient connection to most 7/8″ shaft 1.1 – 5.5 HP engines. The hollow shafted pump includes a built-in pressure control valve, thermal relief valve and chemical injection system. App. 6 1/2″ Tall.
RMW2.2G24-SX-PKG annovi reverberi pressure washer pumps are a combination of exceptional degree of technology and innovation, quality and reliability worthy of a leading brand on the market. The wide range includes many models which vary in terms of pressure, deliver, power and technical characteristics, to satisfy widely different market demands
Annovi Reverberi’s Axial series pumps come with a special formulated Synthetic pump oil that contains anti-wear, rust inhibitor and deoxidizer additives designed to last 500 hours.
Annovi Reverberi RMW22G24SX-PKG
The Annovi Reverberi RMW22G24SX-PKG Features:
RMW22G24-EZ-SX – Pump
Max PSI: 2400
Max GPM: 2.2
RPM: 3400
7/8″ Hollow Shaft
Vertical Gas Engine Flange – Rotated 180° from Standard
TPP140-1/4A – Thermal relief valve
AR1269120 – Detergent tube with filter
List Price: $253.86 Our Price: $163.27 You save $90.59!
Availability:: available for order Product Code: RMW22G24SX-PKG
Annovi Reverberi Pressure Washer Pump
PRICE SUBJECT TO CHANGE. PRICE VALID 10/18/2011
