This is a CAT Pressure Washer Pump 56 triplex [three plunger rods] positive displacement, reciprocating, plunger pump, constructed of a forged brass manifold, 304SS valve assemblies, solid ceramic plungers and standard NBR [Buna-N] seals and o-rings.
Mi-T-M HSP-2403-3MGR Hot Pressure Washer, 2.6 GPM @ 2400 PSI, 211cc OHC SUBARU Engine. The HSP Series is designed with the Mi-T-M patented electro magnetic firing system, which means there is no need for a 12V battery, generator, blower motor and alternator; therefore, making these units especially maintenance friendly.
HSP-2403-3MGR
Pump: Direct drive triplex piston AR pump · Stainless-steel and brass unloader valve · Forged brass manifold · Thermal relief valve · Low pressure detergent injection
Engine: Performance-proven Subaru OHC engine with low-oil protection and recoil start
Frame: Reinforced powder coated steel tube frame with center balanced lifting hook · Powder coated steel hose reel mounting bracket · Wand holder · Solid steel threaded axles · Four pneumatic tires with tubes · Locking tire brake
Components: High quality fuel filter/water separator ensures clean fuel supply · Complete system diagnostic board · Pressure and high limit safety controls · No. 1 or No. 2 diesel or kerosene fired burner (Bio-fuel not approved at this time) · Polyethylene burner fuel tank · Easy coil drain helps prevent freezing in cold weather · Patented Electro Magnetic Firing (EMF) System · Energy efficient top fired powder coated heat exchanger designed for convenient trouble-shooting and easy maintenance · On/off burner switch
Unit Includes: 50-foot x 3/8-inch steel wire-braided pressure hose with screw connects, swivel and bend restrictors · Professional-grade insulated trigger gun with safety lock-off · Adjustable pressure insulated dual lance with 15-degree fixed and detergent nozzle
Miscellaneous: Temperature rise 150°F/66°C above ambient, maximum outlet temperature is 200°F
Mi-T-M HSP-2403-3MGR Hot Pressure Washer
The Mi-T-M HSP-2403-3MGR Hot Pressure Washer Features:
Mi-T-M Pressure Washer Performance-proven OHV engine with low oil protection and recoil start
Direct drive triplex ceramic piston pump with forged brass manifold
Thermal relief valve
Stainless-steel and brass unloader valve
Low pressure detergent injection
Complete system diagnostic board
Pressure and high limit safety controls
No. 1 or No. 2 diesel or kerosene fired burner
Polyethylene burner fuel tank
Temperature rise 150 degrees F/66 degrees C above ambient, maximum outlet temperature 200 degrees F
Wand holder
Locking tire brake
Solid steel threaded axles
Pneumatic tires with tubes (4)
50 foot x 3/8 inch steel wire braided pressure hose with screw connects, swivel, and bend restrictors
Professional grade insulated trigger gun with safety lock-off
Adjustable pressure insulated dual lance with 15 degree fixed and detergent nozzle
One (1) year limited parts and labor warranty
Three (3) year limited warranty on coil
Seven (7) year limited warranty on pump
Two (2) year limited warranty on Honda engine
Three (3) year limited warranty on Subaru engine
The Mi-T-M HSP-2403-3MGR Hot Pressure Washer has the following technical specifications:
PSI 2400
GPM 2.6
Displacement/Engine 211cc Subaru OHC
Gas Tank Cap. 0.95 gallon
Burner Fuel Tank Cap. 4.0 gallon
Burner Fuel Cons. 1.53 gph
BTU Per Hour 205,000
Net Weight 269 lbs.
Shipping Weight 385 lbs.
Length 38 in.
Width 30 in.
Height 38 in.
Our Price: $4,720.00
Mi-T-M Pressure Washer CALL 1-877-824-7763 EXT 124 For Better Price Availability:: Usually Ships in 1 to 2 Days Product Code: HSP-2403-3MGR
RSV3.5G35D-F40 AR (Annovi Reverberi) Pump 3.5 GPM @ 3500 PSI, 1″ Hollow Shaft – Great for most 6 to 9 HP Gas Engines with a straight shaft!
Annovi Reverberi Plunger Pumps are designed for a wide variety of high pressure washing applications. The RSV3.5G35D-F40 Annovi Reverberi Pressure Washer Pumps are constructed of die-cast bodies and feature a forged brass head. Internal components include special thick solid ceramic plungers for long life and durability. Precision cast cooling fins are anodized for maximum heat dissipation. Oversized tapered roller bearings and the precision supports assure proper shaft alignment and maximum life. Valve cages of special designed Ultra-Form provide positive seating and extended life. One-piece connecting rods are either a special alloy aluminum or bronze oversized for strength and load disbursement. These RSV3.5G35D-F40 Annovi Reverberi Pressure Washer Pump are designed for gearbox , belt drive, or coupling drive systems, electric motor 182-184 frame driven systems, or gasoline engine driven systems.
The RSV3.5G35D-F40 Annovi Reverbeir Pressure Washer Pump Features:
Max Flow (GPM): 3.5
Max Flow (L/Min): 13.2
Max Pressure (PSI): 3500
Max Bar: 240
Power EBHP: 10
Bore Dia: 15mm
Stroke: 8.2mm
Crankshaft ID Stamp: 8
Pump Speed (in RPM): 3400
Shaft Diameter: 1″ hollow shaft
The RSV3.5G35D-F40 Annovi Reverbeir Pressure Washer Pump has the following specifications:
Manifold: New high efficiency design concept. (Patented). Forged brass for strength and no porposity for long life and higher hydrostatic pressures.
Bolts: Eight 6mm grade 8.8.
Plungers: Ceramic coated stainless steel.
Crankcase: Precision die-cast, cooling fins and anodized for maximum heat dissipation.
Bearings: Oversized for maximum life and load disbursement, needle bearing on the drive side and ball on the non-drive side. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
Valves, Seats, and Springs: Stainless steel with specially designed Ultra FormTM cages to provide long life and positive seating.
Seals and V-Packings: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
Oil Seals: All are constructed of Buna-N rubber.
Plunger Rods: Stainless steel construction for strength (no plating to scrape off), o-ring plunger sealing system.
Connecting Rods: One piece special alloy aluminum and bronze based, oversized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
Items NOT INCLUDED with your RSV3.5G35D-F40 Annovi Reverberi Pressure Washer Pump that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!
The PUMP GUARD will ‘dump’ any water above 145 degrees F. before it reaches your pump (saving you the trouble of rebuilding your pump)
PRESSURE REGULATOR / UNLOADER – if we list one to the right of the pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.
The INLET WATER FILTER will catch most small debris before it enters your pump
The EZ-START VALVE will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer
The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your pump!
PUMP OIL, you can never have enough on hand! Many pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.
List Price: $673.67
Our Price: $421.71
You save $251.96! Availability:: Usually Ships in 24 Hours Product Code: RSV3.5G35D-F40
Pressure Washer Surface Cleaners
How To Deep Clean Large Flat Surfaces?
The solution is our flat surface cleaners
Pressure washer surface cleaners are powerful and reliable. They are used for high pressure cleaning driveways, concrete floors, parking lots, roofs, warehouses, boat ramps, garage floors, boat decks, and more. The benefits of using these products are clear: effective, shorter working times, enormous energy savings and long useful life due to their high industrial quality. You will be able to complete your power washing tasks in the shortest possible amount of time.
HOW DO SURFACE CLEANERS WORK?
High speed flat surface cleaners can consist of 2 or 3 (dual or tri arm) arms that spin in a counter clock wise direction for up to 1800 RPM (rotations per minute). At the end of each arm you will find a 1/4” MEG 25° spray nozzle that can cover the path from 16” to 30” diameter, depending on the size of the actual round housing. These cleaners can remove dirt for up to 15 times faster then the standard wands and 10 times faster than the water brooms. Operation: the user walks behind the unit holding the two handles from which one of them has a spray gun that works the same like any other pressure washer gun. The arms are connected to the shaft that is part of the spinning head (a mechanism that allows smooth rotation of the arm). These arms rotate/spin with the flow of the water (greater the water volume – the faster the spinning times), which creates a scrubbing action with the water coming out. The spray nozzles are only 1/2” to 2” away from the surface which allows greater cleaning capabilities. The edge of the housing and the brush skirt protect the surrounding area from over spraying. Some of our models come with the casters and some without. Units without the casters are designed to “hover” or “float” above the ground, so the maneuverability is not an issue. The greatest advantage of these machines is that they eliminate the “zebra” stripping usually found on driveways and sidewalks.
Some of the many uses for this pressure washer surface cleaner include:
2) Turn water on and open valve. Open trigger gun for flow of water through nozzles. Nozzles must have flowing spray. If not, remove tips and clean; reassemble, making sure that groove of nozzle is parallel to spray bar. Use Teflon tape when installing nozzles.
3) Start Pressure Washer. The flat surface cleaner is ready for operation.
4) Walk slowly behind the flat surface cleaner, cleaning as you go. If striping occurs, slow down your pace.
5) Periodically check weep hole on bottom of swivel. Water will seep slowly; if water shoots out, stop and replace seals. Swivel assembly can be rebuilt.
6) For maximum effectiveness keep spray nozzles clean. If the machine vibrates, stop and clean spray tips.
7) Lubricate swivel with one squirt of good quality grease every 200 hours of operation or about once a month if used daily. A small amount of grease coming out of the bottom of the swivel is normal.
DO NOT ALLOW MACHINE TO REMAIN STATIONARY ON SOFT SURFACES, SUCH AS WOOD.
CAUTION: Striking any raised obstacle during operation will damage machine. If contact does occur and results in vibration when operating machine, STOP and replace spray bar. Continued operation could result in serious injury or damage to machine.
What are the Benefits of the Flat Surface Cleaner
How much time will this equipment actually save me (versus using the standard wand)?
The following comparison shows the time taken to clean a typical size driveway (400 sq. ft.) using 2 different components.
The SK30005VH Hot Mobile Pressure Washer Skid Series is a truly portable machine, can be truck/trailer mounted and is a real asset when electricity is not available. The industrial rated 14 HP Vanguard twin-cylinder electric-start engine provides power to the pump and 12 VDC burner. Big 20 Amp charging circuit. The stainless steel wrapped 1/2″ SCH 80 coil heats the water up to 250F. You will experience extended run times with the large 8 gallon gas and diesel tanks. An industrial rated belt drive pump turns at a lower RPM resulting in a cooler running and longer lasting pump compared to one that is direct drive. The machine is complete with gun/wand, 50′ high pressure hose, quick connect nozzles, high limit switch, pressure relief valve, burst disc and flow sensitive unloader. Requires group U1 235 CCA battery, not included.
SK30005VH Hot Mobile Pressure Washer Skid Parts Breakdown Click Here
SK30005VH Hot Mobile Pressure Washer Skid
SK30005VH Hot Mobile Pressure Washer Skid Features:
SK30005VH
4.8 GPM
3,000 PSI
14 Hp Vanguard Engine
12 Volt Beckett Burner
Belt Drive AR Pump
K7 Unloader
Adjustable Thermostat
8 Gallon Gas & Diesel Tanks
ST1500 Gun, 48″ Wand, Quick Connect Nozzles
50′ Hose
SK30005VH Hot Mobile Pressure Washer Skid Technical Specifications are:
Engine: Electric-start 14 horsepower Vanguard gas engine with pressure lubrication, automotive style oil filter and low oil shutdown
HSE2003-0M10 Mi-T-M Hot Pressure Washer 220V Pressure Washer 1000 PSI. Looking for quiet operation? This electric hot water washer is ideal for industrial applications.
The HSE2003-0M10 Mi-T-M Hot Pressure Washer is a Compact And Portable Hot Water Cleaning unit.
•Totally enclosed, fan cooled 4.0HP / 230V electric motor
Unique Top Fired Heat Exchanger of the HSE2003-0M10 Mi-T-M Hot Pressure Washer is exceptional.
•Heats water up to 200 degrees F
•Solid state electronic ignition
•Convenient troubleshooting and easy maintenance
•Can use either diesel fuel or kerosene
Direct Drive General Triplex Plunger Pump comes standard with the HSE2003-0M10 Mi-T-M Hot Pressure Washer
•Ceramic components run cooler, last longer
•Easy to maintain and rebuild
The HSE2003-0M10 Mi-T-M Hot Pressure Washer has a Professional Grade Spray Lance With Safety Lock
•Adjustable pressure insulated dual lance
•Includes 15 degree fixed spray and detergent nozzle
•50 feet 3/8″ steel reinforced hose with screw connects
HSE2003-0M10 Mi-T-M Hot Pressure Washer
The HSE2003-0M10 Mi-T-M Hot Pressure Washer Features:
2.8 GPM @ 2000 PSI
4 HP / 230V
Totally enclosed fan-cooled electric motor with manual thermal overload protection
Direct drive triplex piston pump with ceramic plungers and forged brass manifold
Thermal relief valve
Stainless steel and brass unloader valve
High pressure detergent injection
Complete system diagnostic board
Solid state electronic ignition
Pressure and high limit safety controls
No. 1 or No. 2 diesel or kerosene fired burner.
Float tank
Polyethylene burner fuel tank
Temperature rise 150°F/66°C maximum above ambient, maximum 200 degrees F
Water output temperature is approximately 190° to 200°
Easy coil drain
Powder coated steel gun/wand holder
Solid steel threaded axles
Pneumatic tires with tubes (4)
Locking tire brake
3/8 inch x 50 ft steel wire braided pressure hose with screw connects, swivel and bend restrictors
Professional grade insulated dual lance with 15 degree fixed and detergent nozzles
One (1) year limited parts and labor warranty.
Three (3) year limited warranty on coil.
Five (5) year limited warranty on pump.
The HSE2003-0M10 Mi-T-M Hot Pressure Washer Technical Specifications are:
