Mi-T-M Portable Heater Propane Forced Air – MH-0150-NM10
Frame: Heavy-duty steel construction · Easy-lift handle for portability at home or on the job site · Adjustable height angle for heat where you need it
Components: One touch ignition and heat control for easy operation · High performance fan · Automatic shut-off if power is interrupted or flame is extinguished · Enclosed gas controls · Electronic ignition · Propane inlet connector – connects heater to propane tank via a supply hose
Heat Output: Adjustable thermostat
For use in workshops, garages, construction sites and farms with proper ventilation.
Specifications subject to change without notice. Use in accordance with any and all state or local codes, regulations, and/or ordinances.
Please see heater “Owner’s Manual” included with each heater for a complete list of important safety information.
Important Notes:
· Not for use in residential living areas or inadequately ventilated areas.
· Proper ventilation required during operation.
· Must be plugged into an approved standard electrical outlet for operation.
MH-0150-NM10 Mi-T-M Portable Heater Propane Forced Air
The MH-0150-NM10 Mi-T-M Portable Heater Propane Forced Air has the following technical specifications:
Heat Output 150,000 BTU
Hot-Air Flow 435 CFM
AC Power 120 Volt/60Hz/Less than 1.0 Amp
Motor Size 1/9 HP
Fuel Natural Gas
Fuel Consumption 150 cu. ft./hr.
Heating Area 3,800 sq. ft.
Net Weight 24 lbs.
Shipping Weight 35 lbs.
Length 25.1 in.
Width 9 in.
Height 15.5 in.
List Price: $550.00 Our Price: $476.50 You save $73.50! Availability:: available for order Product Code: MH-0150-NM10
Annovi Reverberi Pressure Washer Pump XMV2.5G26D-F25 2.5 GPM @ 2600 PSI
Plunger Pumps are designed for a wide variety of high pressure washing applications. They are constructed with die-cast bodies and feature a brass head. Internal components include special thick solid ceramic plungers for long life and durability. Precision cast cooling fins are anodized for maximum heat dissipation. Oversized needle bearings on the drive side, and ball on the non-drive side together with the precision supports assure positive alignment and centering in relation to the crankcase. Valve cages of special designed Ultra-Form provide positive seating and extended life. Ball bearings on both sides of solid shaft drive pumps. One-piece connecting rods are special alloy aluminum, oversized for strength and load disbursement. These pumps are designed for gearbox , belt drive, or coupling drive systems driven by eletric motor or gasoline driven systems, gasoline engine driven systems.
Forged Brass: Strength and no porosity equals long life. Higher hydrostatic pressures, safety and performance.
Inlet and Discharge Ports: Heavy bosses for added strength.
Offset Discharge Ports: High efficiency, smooth flow.
Bolts: Eight bolts, 6mm, grade 12.9.
Ultra Form Cages: Durability, strength and long life.
Poppets, Seat and Spring: 303 and 400 series stainless steel.
Valve Caps: Machined brass – greater strength.
Packing and Plungers:
High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
Low Pressure Seals: “U” cup double lip Buna-N, good positive seal.
Support Guides: Machined brass, two-piece construction to assure proper plunger alignment and to maximize packing and seal life.
Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
Bearings: Oversized for maximum life and load disbursement, needle bearing on the drive side and ball on the non-drive side. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
Crankcase: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
Rear Cover: precision die-cast, O-ring sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen).
Plunger Rods: Stainless steel construction for strength (no plating to scrape off). O-ring plunger sealing system.
Rod Pins: Precision ground and hardened steel, oversized for load disbursement.
Connecting Rods: One-piece special alloy aluminum based, oversized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
Crankshaft: Forged, precision ground and hardened for extremely long life and durability.
Oil Seals and O-rings: All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
Oil Capacity: 14.5 oz., refer to parts breakdown.
Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
Hot Water: High temperature kits are available to 180º F. Refer to breakdown
Wet End Repair: Very simple no special tools are required.
Mounting Bolt Pattern: Same on the top and bottom of the crankcase for simple drive side change.
Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.
Annovi Reverberi Pressure Washer Pump XMV2.5G26D-F25 has the following specifications:
Max GPM………………2.5
Max LMP…………………………9.5
Max PSI………………….2600
Max Bar………………………….179
Power EBHP……………5
Bore Dia. mm…………………….15
Stroke mm……………….6.2
Weight Lbs………………………..15
Max Temp……………….140°
Oil Capacity………………………14.6oz
Inlet Thread ……………1/2”F
Discharge Thread……………….3/8”F
Items NOT INCLUDED with your Annovi Reverberi Pressure Washer Pump XMV2.5G26D-F25that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!The PUMP GUARD will ‘dump’ any water above 145 degrees F. before it reaches your pump (saving you the trouble of rebuilding your pump)PRESSURE REGULATOR / UNLOADER – if we list one to the right of the pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.
The INLET WATER FILTER will catch most small debris before it enters your pump
The EZ-START VALVE will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer
The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your pump!
PUMP OIL, you can never have enough on hand! Many pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.
List Price: $588.80 Our Price: $369.47 You save $219.33! Availability:: Usually Ships in 24 Hours Product Code: XMV2.5G26D-F25
This is a CAT Pressure Washer Pump 56 triplex [three plunger rods] positive displacement, reciprocating, plunger pump, constructed of a forged brass manifold, 304SS valve assemblies, solid ceramic plungers and standard NBR [Buna-N] seals and o-rings.
Mi-T-M HSP-2403-3MGR Hot Pressure Washer, 2.6 GPM @ 2400 PSI, 211cc OHC SUBARU Engine. The HSP Series is designed with the Mi-T-M patented electro magnetic firing system, which means there is no need for a 12V battery, generator, blower motor and alternator; therefore, making these units especially maintenance friendly.
HSP-2403-3MGR
Pump: Direct drive triplex piston AR pump · Stainless-steel and brass unloader valve · Forged brass manifold · Thermal relief valve · Low pressure detergent injection
Engine: Performance-proven Subaru OHC engine with low-oil protection and recoil start
Frame: Reinforced powder coated steel tube frame with center balanced lifting hook · Powder coated steel hose reel mounting bracket · Wand holder · Solid steel threaded axles · Four pneumatic tires with tubes · Locking tire brake
Components: High quality fuel filter/water separator ensures clean fuel supply · Complete system diagnostic board · Pressure and high limit safety controls · No. 1 or No. 2 diesel or kerosene fired burner (Bio-fuel not approved at this time) · Polyethylene burner fuel tank · Easy coil drain helps prevent freezing in cold weather · Patented Electro Magnetic Firing (EMF) System · Energy efficient top fired powder coated heat exchanger designed for convenient trouble-shooting and easy maintenance · On/off burner switch
Unit Includes: 50-foot x 3/8-inch steel wire-braided pressure hose with screw connects, swivel and bend restrictors · Professional-grade insulated trigger gun with safety lock-off · Adjustable pressure insulated dual lance with 15-degree fixed and detergent nozzle
Miscellaneous: Temperature rise 150°F/66°C above ambient, maximum outlet temperature is 200°F
Mi-T-M HSP-2403-3MGR Hot Pressure Washer
The Mi-T-M HSP-2403-3MGR Hot Pressure Washer Features:
Mi-T-M Pressure Washer Performance-proven OHV engine with low oil protection and recoil start
Direct drive triplex ceramic piston pump with forged brass manifold
Thermal relief valve
Stainless-steel and brass unloader valve
Low pressure detergent injection
Complete system diagnostic board
Pressure and high limit safety controls
No. 1 or No. 2 diesel or kerosene fired burner
Polyethylene burner fuel tank
Temperature rise 150 degrees F/66 degrees C above ambient, maximum outlet temperature 200 degrees F
Wand holder
Locking tire brake
Solid steel threaded axles
Pneumatic tires with tubes (4)
50 foot x 3/8 inch steel wire braided pressure hose with screw connects, swivel, and bend restrictors
Professional grade insulated trigger gun with safety lock-off
Adjustable pressure insulated dual lance with 15 degree fixed and detergent nozzle
One (1) year limited parts and labor warranty
Three (3) year limited warranty on coil
Seven (7) year limited warranty on pump
Two (2) year limited warranty on Honda engine
Three (3) year limited warranty on Subaru engine
The Mi-T-M HSP-2403-3MGR Hot Pressure Washer has the following technical specifications:
PSI 2400
GPM 2.6
Displacement/Engine 211cc Subaru OHC
Gas Tank Cap. 0.95 gallon
Burner Fuel Tank Cap. 4.0 gallon
Burner Fuel Cons. 1.53 gph
BTU Per Hour 205,000
Net Weight 269 lbs.
Shipping Weight 385 lbs.
Length 38 in.
Width 30 in.
Height 38 in.
Our Price: $4,720.00
Mi-T-M Pressure Washer CALL 1-877-824-7763 EXT 124 For Better Price Availability:: Usually Ships in 1 to 2 Days Product Code: HSP-2403-3MGR
RSV3.5G35D-F40 AR (Annovi Reverberi) Pump 3.5 GPM @ 3500 PSI, 1″ Hollow Shaft – Great for most 6 to 9 HP Gas Engines with a straight shaft!
Annovi Reverberi Plunger Pumps are designed for a wide variety of high pressure washing applications. The RSV3.5G35D-F40 Annovi Reverberi Pressure Washer Pumps are constructed of die-cast bodies and feature a forged brass head. Internal components include special thick solid ceramic plungers for long life and durability. Precision cast cooling fins are anodized for maximum heat dissipation. Oversized tapered roller bearings and the precision supports assure proper shaft alignment and maximum life. Valve cages of special designed Ultra-Form provide positive seating and extended life. One-piece connecting rods are either a special alloy aluminum or bronze oversized for strength and load disbursement. These RSV3.5G35D-F40 Annovi Reverberi Pressure Washer Pump are designed for gearbox , belt drive, or coupling drive systems, electric motor 182-184 frame driven systems, or gasoline engine driven systems.
The RSV3.5G35D-F40 Annovi Reverbeir Pressure Washer Pump Features:
Max Flow (GPM): 3.5
Max Flow (L/Min): 13.2
Max Pressure (PSI): 3500
Max Bar: 240
Power EBHP: 10
Bore Dia: 15mm
Stroke: 8.2mm
Crankshaft ID Stamp: 8
Pump Speed (in RPM): 3400
Shaft Diameter: 1″ hollow shaft
The RSV3.5G35D-F40 Annovi Reverbeir Pressure Washer Pump has the following specifications:
Manifold: New high efficiency design concept. (Patented). Forged brass for strength and no porposity for long life and higher hydrostatic pressures.
Bolts: Eight 6mm grade 8.8.
Plungers: Ceramic coated stainless steel.
Crankcase: Precision die-cast, cooling fins and anodized for maximum heat dissipation.
Bearings: Oversized for maximum life and load disbursement, needle bearing on the drive side and ball on the non-drive side. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
Valves, Seats, and Springs: Stainless steel with specially designed Ultra FormTM cages to provide long life and positive seating.
Seals and V-Packings: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
Oil Seals: All are constructed of Buna-N rubber.
Plunger Rods: Stainless steel construction for strength (no plating to scrape off), o-ring plunger sealing system.
Connecting Rods: One piece special alloy aluminum and bronze based, oversized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
Items NOT INCLUDED with your RSV3.5G35D-F40 Annovi Reverberi Pressure Washer Pump that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!
The PUMP GUARD will ‘dump’ any water above 145 degrees F. before it reaches your pump (saving you the trouble of rebuilding your pump)
PRESSURE REGULATOR / UNLOADER – if we list one to the right of the pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.
The INLET WATER FILTER will catch most small debris before it enters your pump
The EZ-START VALVE will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer
The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your pump!
PUMP OIL, you can never have enough on hand! Many pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.
List Price: $673.67
Our Price: $421.71
You save $251.96! Availability:: Usually Ships in 24 Hours Product Code: RSV3.5G35D-F40
