Pump Made Ready XMV3G30D-F24 with VRT3-250 with Bypass & Thermal Relief Valve

Technical Specifications of this Pump Made Ready XMV3G30D-F24 with VRT3-250 with Bypass & Thermal Relief Valve:

Triplex Plunger Pump
Direct Drive with Gas Flange
Maximum Volume: 3.0 GPM
Maximum Discharge Pressure: 3000 PSI
Maximum Pump Speed: 3400 RPM
Minimum Horsepower Requirement: 9.3 hp for gas engines
Shaft Diameter: 1″ ID with gas flange
Weight: 19 lb.

Features of the Pump Made Ready XMV3G30D-F24 with VRT3-250 with Bypass & Thermal Relief Valve:

Manifold: High strength forged brass for long term use
Bolts: eight 6mm grade 12.9
Plungers: A special thick solid ceramic for long life, strong durability and more resilience
Crankcase: Precision die cast, large cooling fins and anodized for maximum heat dissipation. Sight glass, fill and side and bottom drain plugs
Bearings: Ove rsized for maximum life and load disbursement, needle bearing on the drive side and ball on the non drive side.
Valves, Seats, and Springs: Stainless steel with specially designed ultra form cages provide extra long life and positive seating.
Seals and Packings: Continuously lubricating for extended life
Plunger Rods: High strength stainless steel
Connecting Rods: One piece special alloy aluminum based over sized for maximum strength, load disbursement, and long life

The XMV3G30D-F24-VRT3-250 W/BYPASS & THERM RELIEF Valve Pump made ready is designed for easy replacement of most pumps. Remove your old pump and fittings and slide this pump made ready on.

SEE BAPL-6600 TO ADD TESTING TO CART.

Lubrication for thePump Made Ready XMV3G30D-F24 with VRT3-250 with Bypass & Thermal Relief Valve:

Use 20W-30 oil. Change oil after 50 hour break-in period, then in 500 hour intervals thereafter.

Parts Breakdown for the XMV3G30D-F24 Click here.

List Price: $546.46

Our Price: $420.50 Click here to order this pump

You save $125.96!

SHIPPING: Item Ships in 1 to 7 Days
Availability:: In Stock
Product Code: BAPL-5321
Price subject to change on the XMV3G30D-F24 Pump Made Ready with VRT3-250 Unloader and Bypass & Thermal Relief Valves.

August 26, 2014August 26, 2014

AR2189 – Annovi Reverberi Water Seal Kit for RSV Series pumps

A Spotlight on the AR2189 the water seal kit for the RSV series of Pressure Washer Pumps.

AR2189 Water Seal Kit by Annovi Reverberi

This is the water seal and packing kit for the RSV series of Annovi Reverberi pressure washer pumps. The AR2189 kit contains everything you need to repair the wet end of your pressure washer pump. There are enough high pressure and low pressure seals (also called packings) to repair or service up to 3 cylinders on your ar pump.

AR2189 water seal kit contains:

AR1342761 – Gasket, quantity 3
AR1981580 – RIng, quantity 3
AR770260 – O-Ring, quantity 3
AR1260440 – Gasket, quantity 3
AR640070 – O-Ring Quantity 3

This water seal kit can be used to repair many types of Annovi Reverberi Pressure Washer Pumps, including misting pumps, plunger pumps, and even some the the AR Blue Clean Pressure Washing pumps. The AR2189 kit can also be use to fix the pumps used on most of today’s pressure washers from Black and Decker, Husky, Briggs & Stratton, Craftsman and Troy Built to Dewalt, Ex-cell, Job Boss and even the AR Blue Clean line of pressure washers. So whether your pressure washer was purchased from a Home Depot, Lowes, Sears or Ace Hardware or Menards chances are it has an Annovi Reverberi Pump in it and can probably be fix by the AR2189 Water Seal Kit. Check your owners manuals for specific Pump specifications.

List Price: $65.77

Our Price: $40.49 Click here to order this packing / repair kit

You save $25.28!

Availability:: In Stock
Product Code: AR2189
Price subject to change on the AR2189 Kit.

November 20, 2013November 20, 2013

Annovi Reverberi Repair Kits and Individual Repair Parts

Annovi Reverberi Repair Kits and Individual Repair Parts being photographed and updated to make you purchasing easier.

Equipment Trade Service Company has started updating photos on all our pressure washer repair kits and individual repair parts. We choose to start with Annovi Reverberi repair kits and individual repair parts that we have in-stock and ready to ship. We have added over 500 photographs of the actual Annovi Reverberi repair kits contents and the individual repair parts. We are striving to make your purchasing of the repair parts you need for your Annovi Reverberi Pressure Washers easier than ever by adding actual photos of these kits and parts.

So when your Annovi Reverberi Pressure Washer needs repairing do the following:

1 – Go to shopetsonline.com and click on the 1st menu item on the left “Manuals & Breakdowns”
2 – Choose Annovi Reverberi Pump Breakdowns from the list
3 – Find your Annovi Reverberi Pressure Washer pump and open the PDF repair breakdown
4 – Find the part number for the individual repair part or repair kit you think you need.
5 – Copy the part number or kit number from the breakdown
6 – Go back to shopetsonline and put that number in the search field in the top right corner of the page
7 – See your part with an actual Photograph of the part to compare to your broken or worn out part(s)
8 – Add the repair part or repair kit to your shopping cart
9 – If more Annovi Reverberi repair kits or individual repair parts are needed go back to breakdown for your pump and repeat steps 4 – 8
10 – When you’re done adding all your repair kits and parts to our cart simply follow the Checkout prompts on the cart page.

We will be adding all in-stock repair parts and kits for Annovi Reverberi in the coming weeks. We will also add new parts and kits as we get them in stock. When we are done with what we can do for Annovi Reverberi we will move on to another Pressure Washer Pump Manufacture’s repair kits and parts. We will announce in blogs when you can find those live. Please be patient with us as we have over 35,000 pressure washer repair kits and parts for a lot of different Pump makes and models, and it will take some time.

Hopefully this will make your decision to purchase all your Annovi Reverberi pressure washer pumps, parts and kits from shopetsonline.com

Thanks and look out for more updates on this endeavor, as always we want your feed back drop us a note with any suggestions or comments to ets@etscompany.com

August 7, 2013

Annovi Reverberi VRT3-250A unloader

Annovi Reverberi VRT3-250A unloader Features:

Forged valve body – excellent strength
Two inlet ports
Two by-pass ports
Ultra thick inlet and discharge ports – added strength
Color coded spring – easy valve identification
All ports are FNPT

New Design of the Annovi Reverberi VRT3-250A unloader Features:
• Interior Design – more efficient flow and operation
• Dual Locking Nuts – vibration resistant for setting maximum pressures
• New Spring Material – more resistant to fatigue, powder paint resists rusting
• Piston – large diameter, more strength and contact area for shifting alignment
• Discharge Nipple – sealing o-ring has been moved to the lower part of the thread, increases hydro strength and fitting strength
• Shutter Valve – hex design, less contact area for smooth shifting (prevents binding). larger size, longer life and more positive shifting

VRT3 Adjustable Unloader 3,650 PSI (Blue) No Knob
SKU: VRT3-250A
Brand: Annovi Reverberi – AR North America

Newly introduced Mecline VRT3 Unloader with out knob is an updated version of the Arrow Line VRT unloader with a stronger valve body with less porosity.

Technical Specifications on the Annovi Reverberi VRT3-250A unloader:

Spring Color: Blue
Does not included black adjustment knob
Replaces AL606XA
Maximum Pressure: 3,650 PSI
Max. Volume: 8.0 GPM
Adjustable pressure
Brass valve body
Max. Fluid Temp.: 194° F.
Inlet Ports (2): 3/8″ FNPT
Discharge Ports (1): 3/8” FNPT
Weight: 27.9 oz

List Price: $96.44
Our Price: $59.37 Click here to order
You save $37.07!
Availability:: available for order
Product Code: VRT3-250A
Price subject to change on the Annovi Reverberi VRT3-250A unloader

July 22, 2013

Pulsar 280 EZ ST Unloader – 85.300.207

Pulsar 280 EZ ST Unloader – 85.300.207 for your pressure washer pump.

The Pulsar 280 EZ ST Unloader – 85.300.207 Features:

Maximum Pressure: 4,000 PSI
Max. Volume: 7.8 GPM
Adjustable pressure
Brass body
Max. Fluid Temp.: 195 degrees F.
Built-In easy start valve relieves back pressure during engine start up
Inlet Ports (1): 3/8″ FPT
Discharge Ports (1): 3/8” FPT
Bypass Ports (2): 3/8” FPT
** NOTE: Unloader Must Be Installed Vertically For Proper Operation
21.0 OZ. Weight.

The Pulsar 280 EZ ST Unloader is a Trapped Pressure Unloader with built-in Easy Start.

[important]“Trapped Pressure” unloader valves are the most commonly used. These valves sense and are activated by building pressure at the pump output. Trapped Pressure valves initiate bypass mode in direct response to building pressure in the hose between the pump output and the spray gun. They are often simply called “Pressure” valves. A spike of pressure results when cycling is interrupted and Trapped Pressure valves re-release water to the spray gun. Operators should be prepared for the “kickback” effect on the spray gun or wand to avoid loss of control or injury.[/important]

List Price: $73.98
Our Price: $56.93 Click to Order
You save $17.05!
Availability:: available for order
Product Code: 85.300.207 – Pulsar 280 EZ ST Unloader
Price on the Pulsar 280 EZ ST Unloader – 85.300.207 is subject to change.

July 9, 2013

MV580K Unloader for Pressure Washer Pumps

MV580K Unloader for Pressure Washer Pumps.

The MV580k Unloader has the following Techincal Specifications:

• Trapped Pressure Unloader
• Maximum Pressure: 3,600 PSI
• Max. Volume: 8.0 GPM
• Adjustable pressure
• Forged brass body
• Max. Fluid Temp.: 200 degrees F.
• Inlet Port (1): 3/8″ FPT
• Discharge Port (1): 3/8” FPT
• Bypass Port (1): 1/4” FPT
• 1.38 lb. Weight

MV580K Unloader with Knob is rated 3600 PSI, 8.0 GPM
SKU: MV580K
Brand: Mecline

List Price: $88.51
Our Price: $54.48 Order the MV580K Unloader here.
You save $34.03!
Availability:: available for order
Product Code: MV580K
Price Subject to change on the MV580K Unloader.

May 13, 2013

BE 85.205.026 – 36″ GUN & WAND KIT for your Pressure Washer

BE 85.205.026 – 36″ GUN & WAND KIT for your Pressure Washer.

BE 85.205.026 – 36″ Gun and Wand assembly with male plug. 4000 PSI Max, 8 GPM Max, 300 Deg. F Gun with 4000 PSI Max, 12 GPM Max, 300 Deg. F Standard insulated wand.

*3/8″ PLATED STEEL PLUG

Pro-Quality Spray Gun and Wand Assembly Our pro-quality Spray Gun and Wand Assembly features heavy-duty construction and deeply discounted pricing.
It’s ideal for virtually all hot and cold water pressure washers!
(This item is also known as item BE 85.205.026)
This complete spray gun and wand assembly features:
* quality steel wand
* easy-to-grip spray gun with trigger lock
* 36″ length for excellent reach
* new quick-connect coupler at end of wand, which that makes it very easy to attach spray nozzles!
* use with max. pressure of 4,000 PSI, 8 GPM and up to 300F degrees
* comes packaged in a box

List Price: $44.90
Our Price: $34.86 Order the BE 85.205.026 Gun & Wand Kit Click here.
You save $10.04!
Availability:: available for order
Product Code: BEWA-85.205.026
The price of the BE 85.205.026 Gun & Wand Kit for your pressure washer is subject to change.

August 27, 2012

5218301U BECKETT POWERLIGHT 12VDC IGNITOR W/CAD CELL

5218301U BECKETT POWERLIGHT 12VDC IGNITOR W/CAD CELL.

Beckett’s new 5218301U Powerlight ignitors offer improved performance and longer life. Easy to install and is designed as a universal replacement in Beckett and other manufacturer’s burners.

The 5218301U BECKETT POWERLIGHT Features:

External heat sink eliminated for improved performance and reduced frequency of replacement due to overheating and arcing.
Easy change to interrupted ignition to increase ignitor life and save energy.
Lightweight, single piece design is compatible with Beckett and other burners to reduce required inventory.
Fully potted with improved epoxy to withstand thermal shock and protect electronic components: waterproof
Simplified wiring requirements and fewer wires for ease of installation
Cad Cell included with ignitor, but not installed.

The 5218301U BECKETT POWERLIGHT has the following specifications:

Igniter with control board & cad cell
Igniter model # 756401
For use with Beckett ADC
Input: 10.8 to 16VDC 1.8 A
Output: 20KV, 25mA
Weight: 1.75 lbs

List Price: $160.00
Our Price: $128.44 Click the link to purchase the 5218301U Beckett Powerlight Ignitor.
You save $31.56!
Availability:: available for order
Product Code: BAPL-6946
Price Subject to change. Price Valid on the 5218301U Beckett Powerlight Ignitor 8/27/2012

June 18, 2012September 11, 2012

TUFF-GUARD Perfect Garden Hose (PGH)

TUFF-GUARD Perfect Garden Hose (PGH) Spotlight on this Awesome Hose!

TUFF-GUARD truly is the Perfect Garden Hose. The unique polypropylene double helix construction makes this the most flexible and only unkinkable garden hose.

The double helix construction also allows the TUFF-GUARD hose to be 35% – 50% lighter than other garden hoses, flexible and weather resistant from -20°F to 158°F, abrasion and chemical resistant, and crush proof all while retaining its superior durability.

Unlike all other garden hoses, the heavy duty brass ferrules thread onto the outer helix to anchor the couplings making end pull-offs and leaks virtually impossible.

All of these features make this the ideal hose for residential and industrial users. TUFF-GUARD is as suited for washing your car, boat, RV, snowmobile, house or garden watering as it is for wash-down use in industrial plants, rock quarries, cement trucks, landscaping and horse barns.

THE PERFECT WATER HOSE – TUFF GUARD
Best Garden Hose

TUFF-GUARD Perfect Garden Hose (PGH) Features:

KINK-FREE
Maximum Flow Fittings
Professional Grade
Easy Handling
35%-50% Lighter
Flexible from -20°F to 158°F
Inside Diameter: 5/8″
Working PSI: 100
PSI Burst: 300+
Length: 100 FT
Colors:Red, Pink, Grey, Green, Beige, Blue

Construction On this TUFF-GUARD Perfect Garden Hose (PGH)
Tube Clear TPE
Reinforcement Polypropylene 2 Helix Design, Color Blue 2-plyspiral polyester fiber
Cover TPE with color Blue
Packaging Coils, coupled with heavy duty male and female garden hose Fittings
Weight/ft (lbs) 0.130 lbs max

List Price: $135.10
Our Price: $99.76 Click the link to order the TUFF-GUARD Perfect Garden Hose.
You save $35.34!
Availability:: available for order
Product Code: EQHG-22100
Price Subject to change. Price valid on this TUFF-GUARD Perfect Garden Hose (PGH) 6/18/2012

May 10, 2012May 11, 2012

K7.1 UNLOADER

Spotlight on the K7.1 UNLOADER 3.0-4.2 GPM 3500PSI.

The K7.1 UNLOADER Features:

Features all stainless and brass internal parts
Design reduces sensitivity to entrapped air
No external moving parts or springs on this K7.1 UNLOADER
Eliminates high pressure in all lines while unit is in bypass mode
Bypass restrictor eliminates pressure peaks during bypass
Unique balanced piston design permits precise pressure adjustments on this K7.1 UNLOADER
Simple design for easy maintenance and service

The K7.1 UNLOADER has the following specifications:

Maximum Volume: 2.9 to 4.2 GPM
Discharge Pressure: 0 to 3000 PSI
Maximum Temperature: 165 F
Inlet Port: 3/8″ FPT
Outlet Port: 3/8″ MPT
Bypass Port: 3/8″ FPT
Dimensions: 7.50″ x 3.75″ x 3.50″
Weight: 4.5 lb
Repair Kit: Kit 70 Barens Order #1694

Is this K7.1 UNLOADER not the right unloader for your pressure washer? Click the link to see all Unloaders from Shopetsonline.com

List Price: $141.80
Our Price: $109.12 Click the link to order this K7.1 Unloader.
You save $32.68!
Availability:: available for order
Product Code: BAPL-1393
Price subject to change. Price valid on this K7.1 Unloader 5/10/2012