Category: pressure washer pumps

The AR North America RMW2.2G24-ST features a 7/8″ hollow shaft, operates at 3400 RPM, and has a max PSI of 2400. The inlet and outlet tubes are short in this version of the pump. Manifold is made from precision die cast aluminum.

The matching flange on this Annovi reverberi RMW2.2G24-ST pressure washer pump provides convenient connection to most 3/4” shaft 1.1 – 5.5 HP engines. The hollow shafted pump includes a built-in pressure control valve, and chemical injection system.

Annovi Reverberi / AR North America RMW2.2G24-ST, RMW 22G24-ST, RMW 2.2G24-ST Vertical Radial-Axial series replacement pump (Mounts under the engine)

We do not have any mfg cross reference information available. However, RMW pumps fit most vertical engines (pump under the motor) with a 7/8″ straight keyed shaft.

Special Note: Use AR64545 Oil in this Annovi reverberi RMW2.2G24-ST pressure washer pump. Do NOT change oil. Use oil only to add if low. This oil is a specially formulated synthetic with special additives for the demands of this Annovi reverberi RMW2.2G24-ST pressure washer pump. No other oil is factory approved for these pumps, and could result in Annovi reverberi RMW2.2G24-ST pressure washer pump failure.

All positive displacement Annovi reverberi RMW2.2G24-ST pressure washer plunger pumps must have a safety relief valve installed on the discharge side of the pump, this valve could be either an unloader or regulator and must be of adequate flow and pressure for the pump. (This Annovi reverberi RMW2.2G24-ST pressure washer pump has an unloader already built in).  Adequate protective guards must cover all moving parts. Perform routine maintenance on the pump and components.  Use only components that are rated for the flow and pressure of the pump, this would include hose, fittings, safety valves, spray guns etc.

Special Features of the Annovi reverberi RMW2.2G24-ST pressure washer pump

Wet End of the Annovi reverberi RMW2.2G24-ST pressure washer pump:
Manifold: Forged Brass: Strength and no porosity – long life. Higher hydrostatic pressures – safety.
Unloader: Integral trap pressure, fixed chemical injector. Simple repair using a cartridge replacement kit.
Bolts: Three bolts, 6mm grade 8.8.

Valves for the Annovi reverberi RMW2.2G24-ST pressure washer pump:
Ultra Form Cages: Durable, strong, and long life. Poppets and Spring: 303 series stainless steel.
Valve Seat: Brass with an external sealing o-ring on both inlet and discharge valves.
Valve Caps: Machined brass for greater strength.

Packing and Plungers: Dual seal system. High Pressure Packing and Low-Pressure
Seals: “U” cup double lip Buna-N for a good positive seat.
Support and Guides: Special anti-wear plastic, 1-piece construction to assure proper plunger alignment, maximize packing and seal life and prevent plunger wear and damage.

Plungers on this Annovi reverberi RMW2.2G24-ST pressure washer pump:  Solid hardened stainless steel, strong and durable.

Drive End
Bearings: Oversized ball bearing stabilizes the crankshaft and one needle style thrust bearing absorbs the plunger load and assures long radial plate life.

Crankcase: Precision die-cast, with cooling fins for maximum heat dissipation. The housing retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer.

Crankshaft/Wobble Plate: Precision die-cat to assure proper stroke, duration and alignment.

Oil Seals and O-rings: All are constructed of Buna-N rubber. The oil seals have stainless steel garder springs to assure constant tension on the sealing surface.

Oil Capacity: 2.2 oz.

Ports:
Inlet Port: Is supplied with a standard brass garden hose connection with inlet strainer.
Discharge Port: Is supplied with 3/8”M connection.

Accessory Ports: All Annovi reverberi RMW2.2G24-ST pressure washer pump models have a 1/4”F port on the inlet side of the manifold.

Extra Features of the Annovi reverberi RMW2.2G24-ST pressure washer pump:

Dyno Proven: All Annovi reverberi RMW2.2G24-ST pressure washer pump are dyno tested to assure the theoretical design meets the actual design.
Valve Design: Each Annovi reverberi RMW2.2G24-ST pressure washer pump series has a valve design that optimizes its highest efficiency.
Wet End Repair: Very simple no special tools required.
Design: Using advanced fluid handling design programs. Overall Annovi reverberi RMW2.2G24-ST pressure washer pump efficiency is increased.

The Annovi reverberi RMW2.2G24-ST pressure washer pump Features:

• NOTE: This Annovi reverberi RMW2.2G24-ST pressure washer pump DOES NOT fit Karcher units using a hex head bolt to drive the pump.
• Fits most homeowner type vertical pressure washers
• Note: This Annovi reverberi RMW2.2G24-ST pressure washer pump is Back Mounted and turned 180º
• Note: This Annovi reverberi RMW2.2G24-ST pressure washer pump has short inlet and outlet tubes
• Annovi reverberi RMW2.2G24-ST pressure washer pump comes with oil
• Stainless steel plungers
• Aluminum manifold w/aluminum valve plugs
• Outlet Port: 22mm (Twist Connect)
• Inlet Port: 3/4″ FGH (garden hose)
• Maximum Horsepower Requirements: 5.0 GHP
• Built In unloader and chemical injector
• Engine shafts longer that 2” will require spacers or washers

Technical Specifications of the Annovi reverberi RMW2.2G24-ST pressure washer pump are:

The RKV4G40HD-F24 AR (Annovi Reverberi) Pressure Washer Pump:

4 GPM @ 4000 PSI, 1″ Hollow Shaft – great for most 11 to 14 hp engines with a straight shaft! RKV4G40HD-F24 Plunger Pumps are designed for a wide variety of high pressure washing applications. The RKV4G40HD-F24 are constructed of die-cast bodies and feature a forged brass head. The RKV4G40HD-F24 has Internal components include special thick solid ceramic plungers for long life and durability. Precision cast cooling fins are anodized for maximum heat dissipation. Oversized tapered roller bearings and the precision supports assure proper shaft alignment and maximum life. Valve cages of special designed Ultra-Form provide positive seating and extended life. The RKV4G40HD-F24 have One-piece connecting rods are either a special alloy aluminum or bronze oversized for strength and load disbursement. These RKV4G40HD-F24 pumps are designed for gearbox , belt drive, or coupling drive systems, electric motor 182-184 frame driven systems, or gasoline engine driven systems.

PARTS LIST: RKV 3400 rpm

The RKV4G40HD-F24 AR (Annovi Reverberi) Pressure Washer Pump Features:

• MANIFOLD: High strength forged brass or nickel plated for long term use.
• BOLTS: Eight 8mm grade 8.8.
• PLUNGERS: A special thick solid ceramic for long life, strong durability and more resilience.
• CRANKCASE: Precision die-cast, large cooling fins and anodized for maximum heat dissipation. Sight glass, fill and side and bottom drain plugs.
• BEARINGS: Oversized tapered roller bearing for maximum
• life and load distribution.
• BEARINGS SUPPORTS: Precision die-cast and machined to assure concentricity and alignment.
• VALVES, SEATS, AND SPRINGS: Stainless steel with specially designed Ultra Form cages to provide long life and positive seating.
• SEALS AND V-PACKINGS: Continuously lubricating for extended life.
• PLUNGER RODS: Stainless steel construction for strength, no plating to scrape off, back-up and o-ring plunger sealing system.
• CONNECTING RODS: One piece special alloy aluminum or bronze for higher pressure, oversized for maximum strength, load disbursement, and long life. Heavy pin area construction, for added load strength.
• Manifold specifics for RKV4G40HD-F24 pressure washer pump:
• – Forged Brass: Strength and no porosity – long life. higher hydrostatic pressures – safety, performance.
• – Inlet and Discharge Ports: Heavy bosses for added strength.
• – Offset Discharge Ports: High efficiency, smooth flow.
• – Bolts: Eight bolts, 8mm, grade 8.8.
• Valves specifics for RKV4G40HD-F24 pressure washer pump:
• – Valve Caps: Stainless steel on pumps rated at 3200 PSI and higher, better hydrostatic loads. Machined brass on pumps <3200 PSI.
• – Ultra Form Cages: Durable, strength, and long life.
• – Poppets, Seat and Spring: 303 and 400 series stainless steel.
• Packing and Plungers specifics for RKV4G40HD-F24 pressure washer pump:
• – High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
• – Low Pressure Seals: “U” cup double lip Buna-N for a good positive seat.
• – Support and Guides: Machined brass, 1-piece construction to assure proper plunger alignment and to maximize packing and seal life.
• – Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
• Bearings: Oversized tapered roller bearing for maximum life and load disbursement of the RKV4G40HD-F24 Pressure Washer Pump.
• Bearing Support: Precision die-cast and machined to assure concentricity and alignment.
• Crankcase: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
• Rear Cover for the RKV4G40HD-F24 Pressure Washer Pump: Precision die-cast, O-ring sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen).
• Plunger Rods on this RKV4G40HD-F24 Pressure Washer Pump: Stainless steel construction for strength (no plating to scrape off), back-up and O-ring plunger sealing system.
• Rod Pins: Precision ground and hardened steel, oversized for load disbursement.
• Connecting Rods on this RKV4G40HD-F24 Pressure Washer Pump: One-piece special allow aluminum or bronze for higher pressure, oversized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
• Crankshaft: Forged, precision ground and hardened for extremely long life and durability.
• Oil Seals and O-rings on the RKV4G40HD-F24 Pressure Washer Pump: Triple lip oil seals, long life and much less leak prone. All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
• Oil Drains: Quantity of two (2). One in the rear cover and one in the bottom of the crankcase.
• Oil Capacity of the RKV4G40HD-F24 Pressure Washer Pump: 15.5 oz.
• Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
• Valve Design: Each RKV4G40HD-F24 Pressure Washer Pump series has a valve design that optimizes its highest efficiency.

The RKV4G40HD-F24 AR (Annovi Reverberi) Pressure Washer Pump has the following specifications:

• Max GPM………………4 Max
• LMP…………………………15.1
• Max PSI………………….4000
• Max Bar………………………….275
• Power EBHP……………11
• Bore Dia. mm…………………….18
• Stroke mm……………….7
• Weight Lbs………………………..21
• Max Temp……………….140°
• Oil Capacity………………………15oz
• Inlet Thread ……………1/2”F
• Discharge Thread……………….3/8”F

List Price: $1,060.37
Our Price: $507.94 
You save $552.43!

Availability:: available for order
Product Code: ARWP-RTR-RKV4G40HD-F24
Annovi Reverberi Pressure Washer Pump
PRICE SUBJECT TO CHANGE.  PRICE VALID ON THIS RKV4G40HD-F24 Pressure Washer Pump 11/8/2011.

AR (Annovi Reverberi) XTA2G22N pressure washer pump.

AR (Annovi Reverberi)  XTA2G22N pressure washer pump 2.11 GPM @ 2200 PSI , XTA1750rpm

AR (Annovi Reverberi)  XTA2G22N pressure washer pumps are designed for a wide variety of moderate pressure washing applications. This AR (Annovi Reverberi)  XTA2G22N pressure washer pump is constructed with die-cast bodies and feature a brass head. Internal components of the AR (Annovi Reverberi)  XTA2G22N pressure washer pump include special thick solid ceramic plungers for long life and durability. Precision cast cooling fins are anodized for maximum heat dissipation. Oversized needle bearing on the drive sides and ball bearings on the non-drive side assure proper shaft alignment and maximum life. Valve cages of special designed Ultra-Form impervious to water absorption provide positive seating and extended life. One-piece connecting rods are either a special alloy aluminum or bronze at higher pressures, oversized for strength and load disbursement.

The AR (Annovi Reverberi)  XTA2G22N pressure washer pump Features:

• Manifold of the XTA2G22N features:
• – Forged Brass: Strength and no porosity equals long life. Higher hydrostatic pressures, safety, performance.
• – Inlet and Discharge Ports: Heavy bosses for added strength.
• – Offset Discharge Ports: High efficiency, smooth flow.
• – Bolts: Six Bolts, 6mm, grade 12.9.
• Valves of the XTA2G22N features:
• – Ultra Form Cages: Durability, strength and long life of every XTA2G22N pressure washer pump.
• – Poppets, Seat and Spring: 303 and 400 series stainless steel.
• – Valve Caps: Machined brass – greater strength.
• Packing and Plungers of the XTA2G22N features:
• – High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
• – Low Pressure Seals: “U” cup double lip Buna-N. Good positive seal.
• – Support Guides: Machined brass one-piece construction to assure proper plunger alignment and to maximize packing and seal life.
• – Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
• Bearings: Oversized for maximum life and load disbursement, two ball bearings on the solid shaft series and a needle bearing on the drive side and ball on the non-drive side for the hollow shaft series. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
• Crankcase of the XTA2G22N has: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
• Rear Cover of the XTA2G22N: Precision die-cast, precision punched gasket sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen).
• Plunger Rods in the the XTA2G22N have: Stainless steel construction for strength (no plating to scrape off). O-ring plunger sealing system.
• Rod Pins: Precision ground and hardened steel, oversized for load disbursement.
• Connection Rods of the XTA2G22N are: One piece special alloy aluminum based and bronze, oversized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
• Crankshaft for the XTA2G22N: Forged one-piece, precision ground and hardened for extremely long life and durability.
• Oil Seals and O-rings: All XTA2G22N are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
• Oil Capacity: Flat cover 8 oz. and extended cover 10 oz.
• Dyno Proven: All XTA2G22N pumps are dyno tested to assure the theoretical design meets the actual design.
• Valve Design: Each  XTA2G22N pump series has a valve design that optimizes its highest efficiency.
• Hot Water: High temperature kits are available to 180º F. Refer to breakdown.
• Wet End Repair: Very simple no special tools are required.
• Mounting Bolt Pattern: Same on the top and bottom of the crankcase for simple drive side change.
• Design: Using advanced fluid handling design programs. Overall XTA2G22N pump efficiency is increased.

The The AR (Annovi Reverberi)  XTA2G22N pressure washer pump has the following Specifications:

AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump

XJV-E22G24D-F7 AR (Annovi Reverberi) Pump 2.2 GPM @ 2400 PSI
This AR (Annovi Reverberi)  XJV-E22G24D-F7 Pressure Washer Pump is designed for medium duty loads. The AR (Annovi Reverberi)  XJV-E22G24D-F7 Pressure Washer Pump spins at 3400 RPM in a direct drive system coupled with a gasoline engine, the matching flange provides convenient connections to most 3/4” shaft 3.5 – 6.5 HP engines. The AR (Annovi Reverberi)  XJV-E22G24D-F7 Pressure Washer Pump has optional vertical and horizontal setups. Precision die-cast crankcase with large cooling fins for maximum heat dissipation. Seals and V-Packings designed to continuously lubricate for extended life. Built-in unloader to optimize performance while reducing setup time. Integral trap pressure with fixed or adjustable chemical injector.

This AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump Features:

• Manifold:
• – Forged Brass: Strength and no porosity – long life. Higher hydrostatic pressures – safety.
• – Unloader: Built in to optimize performance while reducing setup time. Integral trap pressure, fixed or adjustable chemical injector.
• – Bolts: Three bolts, 10mm, grade 8.8.
• Valves:
• – Ultra Form Cages: Durable, strong, and long life. Unique inlet valve configuration: the valve cage incorporates the high pressure packing head ring.
• – Poppets, Seat and Spring: 303 and 400 series stainless steel.
• – Valve Caps: Machined brass for greater strength.
• Packing and Plungers:
• – High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load. Continuously lubricating for extended life, self lubricating packing/Plunger guide support ring.
• – Low-Pressure Seals: “U” cup double lip Buna-N for a good positive seat.
• – Support and Guides: Machined brass, 1-piece construction to assure proper plunger alignment, maximize packing and seal life.
• – Plungers: Coated ceramic stainless steel, strong and durable. The pump includes a plunger shoe to distribute the additional plunger load.
• Bearings: Angular contact ball bearing stabilizes the crankshaft and one thrust needle bearing absorbs the plunger load and assures long radial plate life. All of the thrust plates are made of heat treated hardened steel for extended life.
• Crankcase: Precision die-cast, large cooling fins and anodized for maximum heat dissipation. Sight glass, fill and drain plugs.
• Rear Cover: Precision die-cast, O-ring sealed. The housing retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer.
• Crankshaft/Wobble Plate: Precision die-cast to assure proper stroke, duration and alignment.
• Oil Seals and O-rings: All are constructed of Buna-N rubber. The oil seals have stainless steel garder springs to assure constant tension on the sealing surface.
• Oil Capacity: 4.5 oz.
• Dyno Proven: All AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump are dyno tested to assure the theoretical design meets the actual design.
• Valve Design: Each AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump series has a valve design that optimizes its highest efficiency.
• Wet End Repair: Very simple no special tools required.
• Mounting Flanges: Gasoline SAE J609a flange. Refer to breakdown.
• Design: Using advanced fluid handling design programs. Overall AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump efficiency is increased.

The AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump has the following Specifications:

• Max GPM………………2.2
• Max LMP…………………………8.3
• Max PSI………………….2400
• Max Bar………………………….166
• Power EBHP……………3.5
• Bore Dia. mm…………………….15
• Stroke mm……………….5.8
• Weight Lbs………………………..11
• Max Temp……………….140°
• Oil Capacity………………………4.5oz
• Inlet Thread ……………1/2”M
• Discharge Thread……………….3/8”M

Click here for the AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump Parts Break Down.

Items NOT INCLUDED with your AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!

The PUMP GUARD will ‘dump’ any water above 145 degrees F. before it reaches your AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump (saving you the trouble of rebuilding your AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump).

PRESSURE REGULATOR / UNLOADER – if we list one to the right of the pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.

The INLET WATER FILTER will catch most small debris before it enters your AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump.

The EZ-START VALVE will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer

The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your pump!

PUMP OIL, you can never have enough on hand! Many pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.

List Price: $375.00
Our Price: $251.63
You save $123.37!
Availability:: available for order
Product Code: XJV-E22G24D-F7
Annovi Reverberi Pressure Washer Pump
PRICE SUBJECT TO CHANGE.  PRICE VALID on this AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump 11/03/2011

AR (Annovi Reverberi) XMV3G32D-F24 Pressure Washer Pump

AR (Annovi Reverberi) XMV3G32D-F24 Pressure Washer Pump 3 GPM @ 3200 PSI
For parts just enter any part number on this breakdown in our search box for pricing and availability.
PARTS LIST: XMV3G32D-F24 Pressure Washer Pump

AR (Annovi Reverberi) XMV3G32D-F24 Pressure Washer Plunger Pumps are designed for a wide variety of high pressure washing applications. The AR (Annovi Reverberi) XMV3G32D-F24 Pressure Washer Pump is constructed with die-cast bodies and feature a brass head. Internal components of the AR (Annovi Reverberi) XMV3G32D-F24 Pressure Washer Pump include special thick solid ceramic plungers for long life and durability. Precision cast cooling fins are anodized for maximum heat dissipation on this AR (Annovi Reverberi) XMV3G32D-F24 Pressure Washer Pump. Oversized needle bearings on the drive side, and ball on the non-drive side together with the precision supports assure positive alignment and centering in relation to the crankcase. Valve cages of special designed Ultra-Form provide positive seating and extended life for this AR (Annovi Reverberi) XMV3G32D-F24 Pressure Washer Pump. Ball bearings on both sides of solid shaft drive pumps. One-piece connecting rods are special alloy aluminum, oversized for strength and load disbursement. This AR (Annovi Reverberi) XMV3G32D-F24 Pressure Washer Pump are designed for gearbox , belt drive, or coupling drive systems driven by electric motor or gasoline driven systems, gasoline engine driven systems.

The AR (Annovi Reverberi) XMV3G32D-F24 Pressure Washer Pump Features:

• • Manifold:
• – Forged Brass: Strength and no porosity equals long life. Higher hydrostatic pressures, safety and performance.
• – Inlet and Discharge Ports: Heavy bosses for added strength.
• – Offset Discharge Ports: High efficiency, smooth flow.
• – Bolts: Eight bolts, 6mm, grade 12.9.
• Valves:
• – Ultra Form Cages: Durability, strength and long life.
• – Poppets, Seat and Spring: 303 and 400 series stainless steel.
• – Valve Caps: Machined brass – greater strength.
• • Packing and Plungers:
• – High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
• – Low Pressure Seals: “U” cup double lip Buna-N, good positive seal.
• – Support Guides: Machined brass, two-piece construction to assure proper plunger alignment and to maximize packing and seal life.
• – Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
• • Bearings: Oversized for maximum life and load disbursement, needle bearing on the drive side and ball on the non-drive side. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
• • Crankcase: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
• • Rear Cover: precision die-cast, O-ring sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen).
• • Plunger Rods: Stainless steel construction for strength (no plating to scrape off). O-ring plunger sealing system.
• • Rod Pins: Precision ground and hardened steel, oversized for load disbursement.
• • Connecting Rods: One-piece special alloy aluminum based, oversized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
• • Crankshaft: Forged, precision ground and hardened for extremely long life and durability.
• • Oil Seals and O-rings: All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
• • Oil Capacity: 14.5 oz., refer to parts breakdown.
• • Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
• • Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
• • Hot Water: High temperature kits are available to 180º F. Refer to breakdown
• • Wet End Repair: Very simple no special tools are required.
• • Mounting Bolt Pattern: Same on the top and bottom of the crankcase for simple drive side change.
• • Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.

The AR (Annovi Reverberi) XMV3G32D-F24 Pressure Washer Pump has the following specifications:

• Max GPM………………3 Max
• LMP…………………………11.4
• Max PSI………………….3200
• Max Bar………………………….220
• Power EBHP……………5.5
• Bore Dia. mm…………………….15
• Stroke mm……………….7.6
• Weight Lbs………………………..16
• Max Temp……………….140°
• Oil Capacity………………………14.6oz
• Inlet Thread ……………1/2”F
• Discharge Thread……………….3/8”F

Items NOT INCLUDED with your XMV3G32D-F24 pump that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!

The PUMP GUARD will ‘dump’ any water above 145 degrees F. before it reaches your pump (saving you the trouble of rebuilding your XMV3G32D-F24 pump)

PRESSURE REGULATOR / UNLOADER – if we list one to the right of the  XMV3G32D-F24 pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.

The INLET WATER FILTER will catch most small debris before it enters your  XMV3G32D-F24 pump.

The EZ-START VALVE ON THIS XMV3G32D-F24 will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer.

The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your XMV3G32D-F24 pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your XMV3G32D-F24 pump!

PUMP OIL, you can never have enough on hand! Many XMV3G32D-F24 pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.

List Price: $597.40
Our Price: $374.76 
You save $222.64!

Availability:: available for order
Product Code: XMV3G32D-F24
Annovi Reverberi Pressure Washer Pump
PRICE SUBJECT TO CHANGE.  PRICE VALID 11/01/2011