Category: pressure washers

Posted on

LANDA SDD Series Pressure Washer

SDD Super Fuel-Efficient, High Volume, Hot Water Pressure Washer with 140° Water Temperature Rise.

•Super Heat Transfer Efficiency with Dual Down-Draft Burners
•Dual-Gun Enabled
•Powered by Gasoline or Diesel; Diesel-Heated
•Belt-Drive Landa Pump with 7-Year Warranty

LANDA SDD Series Pressure Washer
LANDA SDD Series Pressure Washer

The LANDA SDD Series Pressure Washer has the following features:

•Two Super-Efficient Diesel-Fueled Downdraft Burners with super heat transfer efficiency for less fuel consumption resulting in the lowest fuel operating costs in the industry.
•Gasoline-powered Honda or Kawasaki or liquid-cooled, 27 hp diesel Lombardini Engines with keyed electric starter for easy start-up and protection against unauthorized use; polyurethane Battery Box protects and firmly secures battery (battery not included).
•Dual Heating Coils with exclusive doublepass design are easy to access for servicing and insure on-demand hot water.
•Industrial-duty, belt-drive, tri-plunger Landa Pump designed to run at low RPM for long life has 7‑year warranty and single-rail truetrack Pulley Adjustment.
•Corrosion-resistant Float Tank with stainless steel inlet filter and 3/4” float valve with antisiphon backflow protection allows introduction of detergents in high pressure mode.
•Trailer-ready with predrilled Trailer Mounting Brackets and large metal cover placed on the side that faces front for protection of components and accessories while transporting.
•Water-resistant control panel has Voltmeter to monitor generator output, Hour Meter to indicate total operating time, and Adjustable Thermostat to control temperature. For easy troubleshooting, Indicator Lights warn when fuel or oil is low.
•Pre-plumbed with 3‑Way Valve to bypass float tank when drawing water directly from an auxiliary tank.
•Efficient 2,000-Watt Generator produces reliable power for burner.
•Forklift Guides and Lifting Eyes for ease of loading and maneuvering.
•Tri-Lingual Labels for operator protection.
•Adjustable Detergent Valve and optional Steam Valve provide precise high-pressure metering of soap and on-demand wet steam cleaning.
•Insulated, fatiguefree Trigger Gun with stainless steel Variable Pressure Wand feature an ergonomic design.
•Rugged Metal Fuel Tanks are more heat-tolerant than plastic and provide hours of uninterrupted operation.
•Rupture Disk and Thermal Pump Protector protect against excessive heat or pressure.
•Dual Screen Filters on water inlet protect pump from debris.
•Filters and Low-Fuel Shutoff protect against operator neglect.
•Rugged Epoxy Powder Coated 2‑inch square tube Open-Air Steel Frame for ease of servicing and ventilation to prevent overheating; Power Platform is vibration isolated to minimize frame stress.
•Many Safety Features, including a rupture disk, thermal pump protector, flow switches, unloader valve, and low-fuel shutdown help protect your investment in equipment as well as the operators who use it.
•50 ft. of double-wire braid High Pressure Hose rated for up to 6000 PSI and featuring a 24-inch safety hose guard for operator burst protection and Quick-Connect Coupler.

WHY CHOOSE LANDA’s SDD

Landa’s SDD features a super-efficient, dual-burner system that provides a 140°F temperature rise above inlet water temperature with 9.5 GPM of cleaning power at 2500 PSI or 7.8 GPM at 3000 PSI. The SDD supports dual gun operation without a reduction in water temperature. And should one coil go down, the SDD can continue to operate with just one coil until the job is done.* Models are powered by either a Honda or Kawasaki gasoline engine, or a Lombardini diesel engine.

QUALITY: Packed with Landa quality throughout, including a top-of-the-line, belt-drive Landa Pump with low RPM for extended life and a 7‑year warranty.

DURABLE: The extraordinarily rugged frame is made of 2-inch square tube steel with an all-metal power platform cushioned by vibration isolators to minimize frame stress.

EFFICIENT: The SDD’s sleek, clean-burning, dual coils, with double-pass design, heat water faster and more efficiently than other coils allowing you to clean better and faster while saving significantly on fuel costs.

FUNCTIONAL: The SDD is pre-plumbed for drawing water from an auxiliary tank, trailer-ready with included trailer mount brackets, easy to service with open-access design and has forklift guides for portability.

SAFETY: The SDD is certified to UL-1776 safety standards.

* Temperature rise will be less than 140°F with only one coil in operation.

SAVE T HOUSANDS OF DOLLARS IN BURNER FUEL EACH YEAR!
Landa’s SDD uses an average of 21% less burner fuel than comparable pressure washers. Don’t need high volume? Save even more! For jobs where half the SDD’s GPM will suffice, you can get additional fuel and water savings by using one gun equipped with the dual-gun nozzle set option listed below.

LANDA SDD Pressure Washer Specifications:
Engine Gas Diesel
Model No. GPM PSI Engine HP Fuel Tank Tank Pump RPM BTUs L x W x H Ship Weight
SDD8-30324E 7.8 3000 Honda 24 Gasoline 10 20 1460 650,000 60” x 42” x 53” 1,515 lbs
SDD10-25524E 9.5 2500 Kawasaki 27 Gasoline 10 20 1575 750,000 60” x 42” x 53” 1,525 lbs
SDD8-30824E 7.8 3000 Lombardini 27 Diesel N/A 30 1460 650,000 60” x 42” x 53” 1,705 lbs
SDD10-25824E 9.5 2500 Lombardini 27 Diesel N/A 30 1575 750,000 60” x 42” x 53” 1,705 lbs

LANDA SDD Pressure Washer Options:
Part No. Description
8.902-421.0 Dual-Gun Tee Coupler
8.708-714.0 Dual-Gun Nozzle Set (7.8 GPM units)
(includes one each of 0°,15°, 25° & 40° nozzles)
8.708-717.0 Dual-Gun Nozzle Set (9.5 GPM units)
(includes one each of 0°,15°, 25° & 40° nozzles)
8.916-511.0 Steam Valve Kit

Note:LANDA is  constantly improving and updating their products. Consequently, pictures, features, and specifications  may differ slightly from current models. Flow rates and pressure ratings may vary due to variances allowed by manufacturers of LANDA’s machine components. LANDA attempts to keep their machine performance within ±5% of listed specifications.

Posted on

LANDA SLX Series Pressure Washer

SLX – The Only Portable Hot Water Pressure Washer that Delivers 200°F Cleaning at up to 10 GPM!

•Dual-Gun Ready
•Powered by Gasoline
•Diesel; Diesel-Heated
•Belt-Drive Landa Pump with 7-Year Warranty
•3/4″ Schedule 80 Coil

LANDA SLX Series Pressure Washer
LANDA SLX Series Pressure Washer

The LANDA SLX Series Pressure Washer has the following:

•Pre-plumbed with 3-Way Valve to bypass float tank when drawing water directly from an auxiliary tank.
•Extra-large Heating Coil made of cold-rolled, 3/4″ Schedule 80 steel pipe with 5-year warranty; features Stainless Steel Top Wrap; unique lift-out design for easy and quick Coil Access.
•Rugged 2″ x 4″ x 1/8″ thick box steel frame, with compact footprint, shields key components; further protected by weather-resistant Epoxy Powder Coat finish; Power Platform is vibration isolated to minimize frame stress.
•Water-resistant, metal Control Panel has adjustable thermostat, combination hour meter and tachometer, volt meter, burner switch and tri-lingual operating instructions for added safety.
•Industrial-duty tri-plunger Landa Pump designed to run at low RPM for long life, 7-year warranty, with single-rail true-track Pulley Adjustment.
•Adjustable Detergent and Steam Valves provide precise metering of soap and on-demand wet-steam cleaning.
•Illustrated Warning Labels universally understandable for liability protection.
•Gasoline-powered Vanguard and Honda Engines, or watercooled, 16‑27 hp diesel Kohler Engine all come with keyed electric starter for easy start-up and protection against unauthorized use; polyurethane Battery Box with vibration isolators protects and firmly secures battery (battery not included).
•30‑gallon diesel and 16‑gallon gasoline Fuel Tanks (15‑gallon diesel and 10‑gallon gasoline on SLT) provide hours of uninterrupted operation; with elevated fuel lines to  avoid suctioning of settled debris.
•50 ft. of double-wire braid High Pressure Hose rated for up to 6000 PSI and featuring a 24-inch safety hose guard for operator burst protection.
•Efficient 2,000-Watt Generator produces reliable power for burner.
•High-efficiency Burner, with dual rings for “dialing in” air flow, has a Fuel- Water Separator for fuel pump protection.
•Many Safety Features, including a rupture disk, thermal pump protector, flow switch, unloader valve, and safety lock on the trigger gun.
•Corrosion-resistant Float Tank has stainless steel inlet filter and 3/4″ float valve with anti-siphon backflow protection; also allows for introduction of detergents in high pressure mode.
•Insulated, fatigue-free Trigger Gun, with swivel crimp fitting for a tangle-free hose. Stainless steel, dual-lance Variable Pressure Wand features an ergonomic design and easy adjusting of the water pressure while cleaning.

WHY CHOOSE LANDA’s SLX or SLT

When it comes to heavy-duty grease or grime, most high-volume, hot water pressure washers fall short with their 150°F water. Landa’s SLX, and smaller SLT, are the first power washers ever designed to deliver a high-volume flow at 200°F water, hot enough to melt the toughest of oily messes. The SLX delivers enough hot water flow—up to 9.5 GPM—that you can operate two spray guns at the same time!

Other benefits include:

QUALITY: Packed with Landa quality throughout, the SLX and SLT feature a top-of-the-line, belt-drive Landa Pump with 7-year warranty and low RPM for extended life, as well as a giant Schedule 80 heating coil, made of up to 300 ft. of 3/4‑inch steel pipe with 5-year warranty.

DURABILITY: Extraordinarily rugged frame is made of 2-by-4-inch box steel with an all-metal power platform cushioned by 10 vibration isolators to minimize frame stress.

EFFICIENT: The SLX-SLT is heated by a high-efficiency Beckett burner with dual rings for dial-in air flow. The 3/4″ heating coil is amazingly efficient due to its unique “breathing” design so it heats quieter while promoting optimum heat exchange.

FUNCTIONAL: The SLX-SLT has a remarkably compact footprint, is certified to UL-1776 safety standards, is pre-plumbed for drawing water from an auxiliary tank, has six forklift guides for portability and the control panel is ideally positioned for curb access when the unit is mounted on a trailer or truck bed.

SLX  Specifications
Engine Gas Diesel
Model No. GPM PSI Engine CCs(HP) Fuel Tank Tank Pump RPM BTU’s L x W x H SHIP WT.
SLX10-25324E 9.5 2500 Honda 670(24) Gasoline 16 30 1560 887,000 65″ x 36″ x 58″ 2020 lbs.
SLX10-25824E 9.5 2500 Kohler 1028(27) Diesel N/A 40 1470 887,000 65″ x 36″ x 58″ 2160 lbs.
SLT5-30224E 5.2 3000 Vanguard 479(16) Gasoline 10 15 1295 485,000 55″ x 32″ x 51″ 1210 lbs.
SLT6-32324E 5.9 3200 Honda 614(20) Gasoline 10 15 1570 550,000 55″ x 32″ x 51″ 1220 lbs.
SLT8-30324E 7.8 3000 Honda 670(24) Gasoline 10 15 1470 728,000 55″ x 32″ x 51″ 1230 lbs.
SLT5-30824E 4.4 3000 Kohler 686(16) Diesel N/A 26 1295 410,000 62″ x 32″ x 53.5″ 1715 lbs.
SLT6-32824E 5.9 3200 Kohler 1028(27) Diesel N/A 26 1470 588,000 62″ x 32″ x 53.5″ 1785 lbs.
SLT8-30824E 7.8 3000 Kohler 1028(27) Diesel N/A 26 1560 728,000 62″ x 32″ x 53.5″ 1850 lbs.

Note: Landa is constantly improving and updating its products. Consequently, pictures, features, and specifications  may differ slightly from current models. Flow rates and pressure ratings may vary due to variances allowed by manufacturers of their machine components. Landa product performance is certified by the Cleaning Equipment Trade Association (CETA) to be within 5% of listed specifications.

Posted on

PGHW Series, Gasoline-Powered/Diesel/Oil Heated Pressure Washer

For more than a decade, the PGHW has been LANDA’s most popular gasoline-powered, hot water pressure washer. The PGHW combines the versatility of a compact size yet the ruggedness and cleaning power of a full-skid pressure washer.
Five PGHW models deliver cleaning power of up to 5000 PSI with a flow rate of up to 5 GPM. The PGHW is packed with power by reliable Honda, Vanguard or Kawasaki electric-start engines, the PGHW models feature top-of-the-line, oil-bath, tri-plunger, belt-drive and a Land pumps with a 7-year warranty. The heating coil is made of 1/2-inch Schedule 80 cold-rolled pipe (Schedule 160 on 5000 PSI model) with a stainless steel outer top wrap. The sturdy steel frame gets all-weather protection from an epoxy powder coat finish. A 2,000 watt generator provides power for the burner as well as a 120V outlet for low-wattage applications.
LANDA PGHW Pressure Washer
LANDA PGHW Pressure Washer

The LANDA PGHW Pressure Washer has the following Specifications:

•Up to 5 GPM, 5,000 PSI
•Honda, Vanguard or Kawasaki Engines
•LANDA Belt-Drive Pump with 7-Year Warranty
•2,000 Watt Generator
•Rugged tri-plunger High-Pressure Landa Pump with forged brass head and 7‑year warranty, is connected to the engine by a belt-drive assembly that features cast-iron bushing Pulleys and two notched “V” cogged belts, which provide a cooler operation and longer life; also single-rail truetrack Pulley Adjustment makes it easy to alter the belt tension.
•Trailer-ready with pre-drilled Trailer Mounting Brackets and pre-plumbed with 3‑Way Valve to bypass float tank when drawing water directly from an auxiliary tank. (5000 PSI model not trailer ready)
•High-efficiency Burner is mounted on the end for ease of servicing and adjustments.
•Power Platform is mounted on vibration isolators to extend the life of the key components.
•2,000 Watt Generator produces reliable power for burner.
•Heavy-duty Fuel-Water Separator has replaceable element for removing water that can damage burner fuel pump.
•Rupture Disk and Thermal Pump Protector protect against excessive heat or pressure.
•Rugged, 11/2-inch square tube Open-Air Frame with Forklift Guides allows easy access and serviceability and is protected by an all-weather resistant Epoxy Powder Coat Finish.
•Super-duty Horizontal Heating Coil, made of cold-rolled, Schedule 80 steel pipe has a 5‑year warranty and is surrounded by an aluminized steel inner wrap and stainless steel top wrap. (5000 PSI model has Schedule 160 coil and all stainless outer wrap)
•Durable polyurethane Battery Box protects battery and is easy to access.
•Color-coded, polyethylene Fuel Tanks for gasoline (5 gal.) and diesel (10 gal.) are translucent for monitoring fuel level. Diesel tank has Low-Fuel Shutoff to protect the burner fuel pump. Both have elevated fuel lines to prevent debris in fuel from causing damage. (gasoline tank is 10 gal. on 5000 PSI model and 1.5 gal. on 13 HP model)
•Industrial-duty Gasoline-Powered Honda, Vanguard or Kawasaki engine with overhead valves; all have keyed Electric Start.
•Insulated, spring-loaded Trigger Gun with inline Detergent Injection and insulated, stainless steel, dual-lance Variable Pressure Wand make it easy to switch between wash and rinse modes. (5000 PSI model has straight thru wand)
•Helpful Tri-Lingual Labels with operating instructions in English, Spanish and French for owner and operator protection.
•Many Safety Features, including redundant devices such as a rupture disk, thermal pump protector and high-temperature shut down to guard against any build up of excessive pressures or heat.
•Conveniently placed Control Panel can be relocated to front of machine and features Burner On/Off Switch, Low-Fuel Light for fuel pump protection, Adjustable Thermostat to control temperature, and Hour/Tach Meter to indicate engine speed and total operating time.
•Adjustable Detergent Valve for precise high-pressure metering of soap. Optional Steam Valve provides ondemand wet-steam cleaning. (steam valve standard on 5000 PSI model)
•Rust-free Float Tank with stainless steel inlet filter provides backflow protection and inlet Detergent Injection for applying soap while washing in high pressure mode.
•50 ft. of 3/8″, double-wire braid Landa Tuff-Skin Hose featuring a 24-inch Hose Guard for burst protection.
•Four Quick-Couple Nozzles are made of hardened stainless steel and are mounted for ready access.

WHY CHOOSE LANDA’s PGHW

For more than a decade, the PGHW has been Landa’s most popular gasoline powered, hot water pressure washer. It combines the versatility of a compact size yet the ruggedness and cleaning power of a full-skid pressure washer. The five PGHW models deliver cleaning power of up to 5000 PSI with a flow rate of up to 5 GPM. The PGHW is packed with:

QUALITY: Powered by reliable Honda, Vanguard or Kawasaki electric-start engines, the PGHW models feature top-of-the-line, oil-bath, tri-plunger, belt-drive  Landa pumps with 7-year warranty. The heating coil is made of 1/2-inch Schedule 80 cold-rolled pipe (Schedule 160 on 5000 PSI model) with a stainless steel outer top wrap. The sturdy steel frame gets all-weather protection from an epoxy powder coat finish.
VERSATILITY: A 2,000 watt generator provides power for the burner as well as a 120V outlet for low-wattage applications. The PGHW has forklift guides for transporting, brackets for mounting on a trailer, and an optional wheel kit. The large fuel tanks provide hours of continuous cleaning and the float tank, with pre-plumbed 3-way bypass valve, allows high-pressure soap application.

SAFETY: As with all Landa models, the PGHW comes certified to the rigid UL-1776 safety standards, featuring: 24-inch hose guard for burst protection; thermal pump protector; high-temperature shut down to prevent super-high heat build up; and rupture disk to vent any build up of excessive pressure in the heating coil.

PGHW Specifications
Model No. Part No. GPM PSI Engine CCs(HP) Start Pump RPM BTU’s L x W x H SHIP WT.
PGHW4-30324E 1.110-048.0 3.5 3000 Honda 389(13) Electric 1125 372,000 48″ x 32″ x 44″ 725 lbs.
PGHW5-30224E 1.110-046.0 4.8 3000 Vanguard 479(16) Electric 1375 470,000 48″ x 32″ x 44″ 700 lbs.
PGHW5-35324E 1.110-045.0 4.7 3500 Honda 614(20) Electric 1360 385,000 48″ x 32″ x 44″ 750 lbs.
PGHW4-40324E 1.110-047.0 4.0 4000 Honda 614(20) Electric 1425 372,000 48″ x 32″ x 44″ 735 lbs.
PGHW5-50524E 1.110-512.0 5.0 5000 Kawasaki 745(27) Electric 1585 470,000 48″ x 39″ x 42″ 1285 lbs.

Note: LANDA is  constantly improving and updating their products. Consequently, pictures, features, and specifications  may differ slightly from current models. Flow rates and pressure ratings may vary due to variances allowed by manufacturers of LANDA’s machine components. LANDA attempts  to keep their machine performance within ±5% of listed specifications.

OPTIONS:
Part No. Description
8.916-588.0 Stainless Steel Bottom Wrap (factory installed)
8.916-585.0 Steam Valve Kit
8.904-525.0 Wheel Kit (not for 5000 PSI model)
8.915-496.0 360° Pivot Hose Reel Kit (100 ft capacity)
8.903-522.0 Non-Pivot Hose Reel Mounting Kit
8.711-858.0 175 ft Cox Hose Reel
9.804-067.0 100 ft E-Zee Hose Reel

Posted on

Mi-T-M HSP-2403-3MGR Hot Pressure Washer

Mi-T-M HSP-2403-3MGR Hot Pressure Washer, 2.6 GPM @ 2400 PSI, 211cc OHC SUBARU Engine. The HSP Series is designed with the Mi-T-M patented electro magnetic firing system, which means there is no need for a 12V battery, generator, blower motor and alternator; therefore, making these units especially maintenance friendly.

HSP-2403-3MGR

Pump: Direct drive triplex piston AR pump · Stainless-steel and brass unloader valve · Forged brass manifold · Thermal relief valve · Low pressure detergent injection

Engine: Performance-proven Subaru OHC engine with low-oil protection and recoil start

Frame: Reinforced powder coated steel tube frame with center balanced lifting hook · Powder coated steel hose reel mounting bracket · Wand holder · Solid steel threaded axles · Four pneumatic tires with tubes · Locking tire brake

Components: High quality fuel filter/water separator ensures clean fuel supply · Complete system diagnostic board · Pressure and high limit safety controls · No. 1 or No. 2 diesel or kerosene fired burner (Bio-fuel not approved at this time) · Polyethylene burner fuel tank · Easy coil drain helps prevent freezing in cold weather · Patented Electro Magnetic Firing (EMF) System · Energy efficient top fired powder coated heat exchanger designed for convenient trouble-shooting and easy maintenance · On/off burner switch

Unit Includes: 50-foot x 3/8-inch steel wire-braided pressure hose with screw connects, swivel and bend restrictors · Professional-grade insulated trigger gun with safety lock-off · Adjustable pressure insulated dual lance with 15-degree fixed and detergent nozzle

Miscellaneous: Temperature rise 150°F/66°C above ambient, maximum outlet temperature is 200°F

Mi-T-M HSP-2403-3MGR Hot Pressure Washer
Mi-T-M HSP-2403-3MGR Hot Pressure Washer

The Mi-T-M HSP-2403-3MGR Hot Pressure Washer Features:

  • Mi-T-M Pressure Washer Performance-proven OHV engine with low oil protection and recoil start
  • Direct drive triplex ceramic piston pump with forged brass manifold
  • Thermal relief valve
  • Stainless-steel and brass unloader valve
  • Low pressure detergent injection
  • Complete system diagnostic board
  • Pressure and high limit safety controls
  • No. 1 or No. 2 diesel or kerosene fired burner
  • Polyethylene burner fuel tank
  • Temperature rise 150 degrees F/66 degrees C above ambient, maximum outlet temperature 200 degrees F
  • Wand holder
  • Locking tire brake
  • Solid steel threaded axles
  • Pneumatic tires with tubes (4)
  • 50 foot x 3/8 inch steel wire braided pressure hose with screw connects, swivel, and bend restrictors
  • Professional grade insulated trigger gun with safety lock-off
  • Adjustable pressure insulated dual lance with 15 degree fixed and detergent nozzle
  • One (1) year limited parts and labor warranty
  • Three (3) year limited warranty on coil
  • Seven (7) year limited warranty on pump
  • Two (2) year limited warranty on Honda engine
  • Three (3) year limited warranty on Subaru engine

The Mi-T-M HSP-2403-3MGR Hot Pressure Washer has the following technical specifications:

  • PSI 2400
  • GPM 2.6
  • Displacement/Engine 211cc Subaru OHC
  • Gas Tank Cap. 0.95 gallon
  • Burner Fuel Tank Cap. 4.0 gallon
  • Burner Fuel Cons. 1.53 gph
  • BTU Per Hour 205,000
  • Net Weight 269 lbs.
  • Shipping Weight 385 lbs.
  • Length 38 in.
  • Width 30 in.
  • Height 38 in.

Our Price: $4,720.00
Mi-T-M Pressure Washer
CALL 1-877-824-7763 EXT 124 For Better Price

Availability:: Usually Ships in 1 to 2 Days
Product Code: HSP-2403-3MGR

Posted on

SK30005VH Hot Mobile Pressure Washer Skid

The SK30005VH Hot Mobile Pressure Washer Skid Series is a truly portable machine, can be truck/trailer mounted and is a real asset when electricity is not available.  The industrial rated 14 HP Vanguard twin-cylinder electric-start engine provides power to the pump and 12 VDC burner.  Big 20 Amp charging circuit.  The stainless steel wrapped 1/2″ SCH 80 coil heats the water up to 250F.  You will experience extended run times with the large 8 gallon gas and diesel tanks.  An industrial rated belt drive pump turns at a lower RPM resulting in a cooler running and longer lasting pump compared to one that is direct drive.  The machine is complete with gun/wand, 50′ high pressure hose, quick connect nozzles, high limit switch, pressure relief valve, burst disc and flow sensitive unloader.  Requires group U1 235 CCA battery, not included.

SK30005VH Hot Mobile Pressure Washer Skid Parts Breakdown Click Here

SK30005VH Hot Mobile Pressure Washer Skid

SK30005VH Hot Mobile Pressure Washer Skid Features:

  • SK30005VH
  • 4.8 GPM
  • 3,000 PSI
  • 14 Hp Vanguard Engine
  • 12 Volt Beckett Burner
  • Belt Drive AR Pump
  • K7 Unloader
  • Adjustable Thermostat
  • 8 Gallon Gas & Diesel Tanks
  • ST1500 Gun, 48″ Wand, Quick Connect Nozzles
  • 50′ Hose

SK30005VH Hot Mobile Pressure Washer Skid Technical Specifications are:

  • Engine: Electric-start 14 horsepower Vanguard gas engine with pressure lubrication, automotive style oil filter and low oil shutdown
  • Pump: belt drive, ceramic plunger pump
  • Capacity: 4.8 gpm @ 3,000 psi
  • Burner: diesel fired 12 volt burner system
  • Temp. Control: adjustable thermostat
  • Coil: Schedule 80 boiler grade pipe
  • Tank: 8 gallon diesel and 8 gallon gas
  • Frame: heavy duty powder coated
  • **Soap: down stream chemical injection
  • **Wheels: four-13” foam filled
  • Accessories: 50’ hose, quick connect nozzles, pressure relief valve, burst disc, flow sensitive unloader
  • Weight/Dimensions 400# – 41″ x 23″ 42″ (LxWxH)

Our Price: $3,899.00 
Pressure Washer
CALL 1-877-824-7763 EXT 124 For Better Price

Availability:: Usually Ships in 1 to 2 Days
Product Code: SK30005VH

Posted on

HSE2003-0M10 Mi-T-M Hot Pressure Washer

GUARANTEED SHIPPED IN 3 DAYS!

HSE2003-0M10 Mi-T-M Hot Pressure Washer 220V Pressure Washer 1000 PSI. Looking for quiet operation? This electric hot water washer is ideal for industrial applications.

The HSE2003-0M10 Mi-T-M Hot Pressure Washer is a Compact And Portable Hot Water Cleaning unit.
•Totally enclosed, fan cooled 4.0HP / 230V electric motor

Unique Top Fired Heat Exchanger of the HSE2003-0M10 Mi-T-M Hot Pressure Washer is exceptional.
•Heats water up to 200 degrees F
•Solid state electronic ignition
•Convenient troubleshooting and easy maintenance
•Can use either diesel fuel or kerosene

Direct Drive General Triplex Plunger Pump comes standard with the HSE2003-0M10 Mi-T-M Hot Pressure Washer
•Ceramic components run cooler, last longer
•Easy to maintain and rebuild

The HSE2003-0M10 Mi-T-M Hot Pressure Washer has a Professional Grade Spray Lance With Safety Lock
•Adjustable pressure insulated dual lance
•Includes 15 degree fixed spray and detergent nozzle
•50 feet 3/8″ steel reinforced hose with screw connects

HSE2003-0M10 Mi-T-M Hot Pressure Washer

The HSE2003-0M10 Mi-T-M Hot Pressure Washer Features:

  • 2.8 GPM @ 2000 PSI
  • 4 HP / 230V
  • Totally enclosed fan-cooled electric motor with manual thermal overload protection
  • Direct drive triplex piston pump with ceramic plungers and forged brass manifold
  • Thermal relief valve
  • Stainless steel and brass unloader valve
  • High pressure detergent injection
  • Complete system diagnostic board
  • Solid state electronic ignition
  • Pressure and high limit safety controls
  • No. 1 or No. 2 diesel or kerosene fired burner.
  • Float tank
  • Polyethylene burner fuel tank
  • Temperature rise 150°F/66°C maximum above ambient, maximum 200 degrees F
  • Water output temperature is approximately 190° to 200°
  • Easy coil drain
  • Powder coated steel gun/wand holder
  • Solid steel threaded axles
  • Pneumatic tires with tubes (4)
  • Locking tire brake
  • 3/8 inch x 50 ft steel wire braided pressure hose with screw connects, swivel and bend restrictors
  • Professional grade insulated dual lance with 15 degree fixed and detergent nozzles
  • One (1) year limited parts and labor warranty.
  • Three (3) year limited warranty on coil.
  • Five (5) year limited warranty on pump.

The HSE2003-0M10 Mi-T-M Hot Pressure Washer Technical Specifications are:

  • Model Number: HSE-2003-0M10
  • Manufacturer: Mi-T-M
  • Made in USA: Unknown
  • Motor
  • Motor Type: Other
  • Motor Voltage: 240-Volt Single-Phase
  • Amps: 18 Amps
  • Power Cord Length: 35 ft GFCI
  • Pump
  • Pump Brand: General
  • Pump Type: Triplex Plunger
  • Adjustable Pressure: No
  • Chemical Injection: Siphon Tube
  • Pump Consumer Warranty: 7 Years
  • Housing
  • Frame Type: 4-Wheel Frame
  • Wheels: Pneumatic
  • Hose
  • Hose Storage: Hook
  • Hose Length: 50 ft
  • Hose Material: Rubber
  • Hose Diameter: 3/8 Inch
  • Hose Connections: Threaded
  • Spray Gun
  • Spray Gun Connection: Threaded
  • Spray Gun Grade: Professional
  • Spray Gun Wand: Dual Wand
  • Spray Tips: Not Applicable
  • Turbo Nozzle: Unknown
  • Overview
  • Burner Fuel: Diesel/Kerosene
  • Burner Fuel Tank Size: 4
  • Temperature Control: Fixed
  • Water Tank Size: Unknown
  • Weight: 270 Lbs. (122.47 kilograms)
  • Dimensions: 34L x 29W x 33H
  • (86.36 x 73.66 x 83.82 cm)
  • Mfr Consumer Warranty: 1 Year

Our Price: $3,880.00
Mi-T-M Pressure Washer
CALL 1-877-824-7763 EXT 124 For Better Price

Product Code: HSE2003-0M10

Posted on

Steam Jenny 1223-C Pressure Washer / Steam Cleaner

Steam Jenny 1223-C  Oil Fired Combination Unit Steam Cleaner / Pressure Washer.

Jenny Oil Fired Combination Units demonstrate the culmination of advanced engineering, state of the art manufacturing, and extensive steam cleaner and pressure washer experience dating back to its inception in 1927 by Jenny.

These units combine an extensive list of standard features with rugged strength and versatility.

Steam Jenny 1223-C Pressure Washer / Steam Cleaner

 

The Steam Jenny 1223-C Pressure Washer / Steam Cleaner Features:

  • Belt Driven Triplex Ceramic Plunger Pump
  • Nozzle Control
  • Flow Actuated Unloader
  • High Pressure Relief Valve
  • High Pressure Solution System
  • Lighted, Panel Mounted, Rocker Switches
  • Stainless Steel Float Tank
  • Stainless Steel Cover
  • Stainless Steel Coil Casing Ring
  • 0, 15, 25, & 40° Color Coded Nozzles
  • Quick Connect Steam Nozzles
  • 3/8″ x 50 Foot Hose
  • 1 Year Machine Limited Warranty
  • 5 Year Chassis Limited Warranty

The Technical Specifications of the Steam Jenny 1223-C Pressure Washer / Steam Cleaner are:

  • Pressure Wash – Pressure – PSI 1200
  • Pressure Wash – Volume-GPM 2.3
  • Pressure Wash – Temperature Rise Up to 140 °F
  • Steam Cleaner – Pressure-PSI 100-200
  • Steam Cleaner – Volume – GPH 70
  • Steam Cleaner – Temperature 325 °F
  • Motor/Engine Horsepower
  • Electric Motor 1-1/2 HP
  • 115 Volt – 1 Phase with GFCI Standard
  • 230 Volt – 1 Phase with GFCI Optional
  • 230 Volt – 3 Phase N/A
  • 460 Volt – 3 Phase N/A
  • 575 Volt – 3 Phase N/A
  • Gasoline Engine N/A
  • Burner Type Jenny Twin Fire Modular Gun Burner
  • 24 Volt Intrinsically Safe Control Voltage Standard
  • Fuel Capacity 7.7 Gallons
  • Solution Capacity Separate Container

Our Price: $4,120.00
Steam Jenny Pressure Washer
CALL 1-877-824-7763 EXT 124 For Better Price

Product Code: 1223-C

Click here for the Steam Jenny 1223-C Pressure Washer / Steam Cleaner Machine Breakdown


Posted on

HSE-1502-0M10 Mi-T-M Hot Pressure Washer

Mi-T-M HSE-1502-0M10 Hot Water 110V Pressure Washer 1500 PSI. Looking for quiet operation? This electric hot water washer is ideal for industrial applications.
GUARANTEED SHIPPED IN 3 DAYS!

HSE-1502-0M10 Mi-T-M Hot Pressure Washer

This Mi-T-M HSE-1502-0M10 Hot Pressure Washer Features:

  • 2 GPM @ 1500 PSI
  • 2 HP / 120V
  • Totally enclosed fan-cooled electric motor with manual thermal overload protection
  • Direct drive triplex piston pump with ceramic plungers and forged brass manifold
  • Thermal relief valve
  • Stainless steel and brass unloader valve
  • High pressure detergent injection
  • Complete system diagnostic board
  • Solid state electronic ignition
  • Pressure and high limit safety controls
  • No. 1 or No. 2 diesel or kerosene fired burner.
  • Float tank
  • Polyethylene burner fuel tank
  • Temperature rise 150°F/66°C maximum above ambient, maximum 200 degrees F
  • Water output temperature is approximately 190° to 200°
  • Easy coil drain
  • Powder coated steel gun/wand holder
  • Solid steel threaded axles
  • Pneumatic tires with tubes (4)
  • Locking tire brake
  • 3/8 inch x 50 ft steel wire braided pressure hose with screw connects, swivel and bend restrictors
  • Professional grade insulated dual lance with 15 degree fixed and detergent nozzles
  • One (1) year limited parts and labor warranty.
  • Three (3) year limited warranty on coil.
  • Five (5) year limited warranty on pump.

Our Price: $3,555.00
Mi-T-M Pressure Washer
CALL 1-877-824-7763 EXT 124 For Better Price

Product Code: HSE-1502-0M10

The Technical Specifications for the Mi-T-M HSE-1502-0M10 Hot Pressure Washer Are:

  • PSI 1500
  • GPM 2.0
  • HP/Motor 2.0/120V, 1Ø, 19.0A
  • Plug Type NEMA 5-20P
  • Burner Fuel Tank Cap. 4.0 gallon
  • Burner Fuel Cons. 1.33 gph
  • BTU Per Hour 186,000
  • Weights & Dimensions
  • Net Weight 250 lbs.
  • Shipping Weight 373 lbs.
  • Length 34 in.
  • Width 29 in.
  • Height 33 in.
Posted on

Mi-T-M Hot Pressure Washer HSE1002-0M11

Mi-T-M Hot Pressure Washer HSE1002-0M11 110V Pressure Washer 1000 PSI. Looking for quiet operation?  This electric hot water washer is ideal for industrial applications.

The Mi-T-M Hot Pressure Washer HSE1002-0M11 Features:

  • 2 GPM @ 1000 PSI
  • 1.5 HP / 120V
  • Totally enclosed fan-cooled electric motor with manual thermal overload protection
  • Direct drive triplex piston pump with ceramic plungers and forged brass manifold
  • Thermal relief valve
  • Stainless steel and brass unloader valve
  • Low pressure detergent injection
  • Complete system diagnostic board
  • Solid state electronic ignition
  • Pressure and high limit safety controls
  • No. 1 or No. 2 diesel or kerosene fired burner.
  • Polyethylene burner fuel tank
  • Temperature rise 150°F/66°C maximum above ambient, maximum 200 degrees F
  • Water output temperature is approximately 190° to 200°
  • Easy coil drain
  • Powder coated steel gun/wand holder
  • Solid steel threaded axles
  • Pneumatic tires with tubes (4)
  • Locking tire brake
  • 3/8 inch x 50 ft steel wire braided pressure hose with screw connects, swivel and bend restrictors
  • Professional grade insulated dual lance with 15 degree fixed and detergent nozzles
  • One (1) year limited parts and labor warranty.
  • Three (3) year limited warranty on coil.
  • Five (5) year limited warranty on pump.
HSE1002-0M11 Mi-T-M Hot Pressure Washer

The Mi-T-M Hot Pressure Washer HSE1002-oM11 has the following specifications:

  • PSI: 1000
  • GPM: 2.0
  • HP/Motor: 1.5 HP/120 Volt
  • Plug Type: NEMA 5-15P
  • Burner Fuel Tank Capacity: 4.0 Gallon
  • Burner Fuel Cons: 1.33 GPH
  • Length: 34 Inches
  • Width: 29 Inches
  • Height: 33 Inches

Our Price: $3,345.00
CALL 1-877-824-7763 EXT 124 For Better Price

Product Code: HSE1002-0M11

Posted on

HSE-1002-SM10 Mi-T-M Hot Pressure Washer / Steam Combination Unit

HSE-1002-SM10 Mi-T-M Hot Pressure Washer / Steam Combination Unit

Hot Water 110V Pressure Washer 1000 PSI. Steam Combination Unit. This compact, portable, hot water pressure washer offers quiet operation and is suitable for a wide variety of industrial applications.

HSE-1002-SM12

Pump: Direct drive triplex piston AR pump with ceramic plungers · Stainless-steel and brass unloader valve · Forged brass manifold · Thermal relief valve · High pressure detergent injection

Motor: Totally enclosed fan-cooled electric motor with manual thermal overload protection · 35-foot power cord with in-line GFCI which meets required CSA certification · Solid state electronic ignition

Frame: Reinforced powder coated steel tube frame with center balanced lifting hook · Powder coated steel hose reel mounting bracket · Electric cord hanger · Powder coated steel gun/wand holder • Solid steel threaded axles · Four pneumatic tires with tubes · Locking tire brake

Components: Complete system diagnostic board · Float tank · Pressure and high limit safety controls · No. 1 or No. 2 diesel or kerosene fired burner (Bio-fuel not approved at this time) · Polyethylene burner fuel tank · Easy coil drain helps prevent freezing in cold weather · Energy efficient top-fired heat exchanger designed for convenient trouble-shooting and easy maintenance · High-quality fuel filter/water separator ensures clean fuel supply · Combination wet steam cleaner/pressure washer

Unit Includes: 50-foot x 3/8-inch steel wire-braided pressure hose with screw connects, swivel and bend restrictors · Professional-grade insulated trigger gun with safety lock-off · Adjustable pressure insulated dual lance with 15-degree fixed and detergent nozzle

Miscellaneous: Temperature rise 150°F/66°C above ambient, maximum outlet temperature is 200°F · Water output temperature for “wet” steam is approximately 250°F · Operates at 650-PSI in “wet” steam mode

HSE-1002-SM10 Mi-T-M Hot Pressure Washer / Steam Combo Unit

The HSE-1002-SM10 Mi-T-M Hot Pressure Washer / Steam Combo Unit Features:

  • 2 GPM @ 1000 PSI
  • 1.5 HP / 120V
  • Totally enclosed fan-cooled electric motor with manual thermal overload protection
  • Direct drive triplex piston pump with ceramic plungers and forged brass manifold
  • Thermal relief valve
  • Stainless-steel and brass unloader valve
  • High pressure detergent injection
  • Complete system diagnostic board
  • Solid state electronic ignition
  • Float tank
  • Pressure and high limit safety controls
  • No. 1 or No. 2 diesel or kerosene fired burner
  • Polyethylene burner fuel tank
  • Temperature rise 150°F/66°C above ambient, maximum outlet temperature 200 degrees F
  • Water output temperature for “wet” steam is approximately 250°
  • Operates at 650 PSI in “wet” steam mode
  • Easy coil drain
  • Powder coated steel gun/wand holder
  • Adjustable pressure insultated dual lance with 15 degree fixed & detergent nozzles
  • Solid steel threaded axles
  • Pneumatic tires with tubes (4)
  • Locking tire brake
  • 50 foot x 3/8-inch steel wire braided pressure hose with screw connects, swivel and bend restrictors
  • Professional grade insulated dual lance with 15 degree fixed and detergent nozzles
  • One (1) year limited parts and labor warranty.
  • Three (3) year limited warranty on coil.
  • Seven (7) year limited warranty on pump.
  • One (1) year limited warranty on electric motor
  • * Combination Steam Cleaner/Pressure Washer

The specifications for this Mi-T-M Hot Pressure Washer / Steam Combo Unit # HSE-1002-SM10 are:

  • PSI 1000
  • GPM 2.0
  • HP/Motor 1.5/120V, 1Ø, 15.0A
  • Burner Fuel Tank Cap. 4.0 gallon
  • Burner Fuel Cons. 1.33 gph
  • BTU Per Hour 186,000
  • Weights & Dimensions
  • Net Weight 245 lbs.
  • Shipping Weight 368 lbs.
  • Length 34 in.
  • Width 29 in.
  • Height 33 in.

CALL 1-877-824-7763 EXT 124 For Better Price

Our Price: $3,305.00 


Product Code: HSE-1002-SM10