Tag: pumps

Posted on

GIANT Pressure Washer PUMP P313

Spotlight on the GIANT Pressure Washer PUMP P313.

Description: LANDA – GIANT Pressure Washer PUMP P313 RIGHT-HAND SHAFT – 8.702-356.0

The GIANT Pressure Washer PUMP P313 Features:

  • Volume ………………………………………………… Up to 3.8 GPM ………(14.4 LPM)
  • Discharge Pressure P313 (Continuous) ……… Up to 3200 PSI ……… (220 bar)
  • Discharge Pressure P313 (Intermittent) ……… Up to 3500 PSI ……………(240 bar)
  • Discharge Pressure P314 (Continuous) ……… Up to 3500 PSI ……… (240 bar)
  • Discharge Pressure P314 (Intermittent) ……… Up to 4000 PSI ……… (275 bar)
  • Inlet Pressure ………………………………………………………………………. Positive Inlet Pressure Required
  • Stroke ………………………………………………….. 0.55”……………………14.1mm
  • RPM…………………………………………………………………………………..Up to 3450 RPM
  • Plunger Diameter …………………………………… 0.47”……………………12mm
  • Temperature of Pumped Fluids ………………… Up to 160 oF ………….(71 oC)
  • Inlet Ports …………………………………………………………………………… (2) 1/2″ BSP
  • Discharge Ports …………………………………………………………………… (2) 3/8″ BSP
  • Shaft Rotation ……………………………………….. Top of pulley towards manifold
  • Crankshaft Diameter ……………………………………………………………..24mm
  • Key Width …………………………………………………………………………..8mm
  • Shaft Mounting ……………………………………………………………………. Either side2
  • Weight …………………………………………………. 16 lbs. …………………. (7.26 kg)
  • Crankcase Oil Capacity ………………………….. 14.2 fl.oz. …………….. (0.42 liters)
  • Extended Crankcase Oil Capacity …………….. 17 fl. oz. ………………. (0.5 liters)
GIANT Pressure Washer PUMP P313
GIANT Pressure Washer PUMP P313

 

The repair Manual for the Giant Pressure Washer Pump P313 can be found by clicking here.

GIANT Pressure Washer PUMP P313
GIANT Pressure Washer PUMP P313

INSTALLATION INSTRUCTIONS FOR THE GIANT Pressure Washer PUMP P313

Installation of the Giant Industries, Inc., pump is not a complicated procedure, but there are some basic steps common to all pumps. The following information is to be considered as a general outline for installation. If you have unique requirements, please contact Giant Industries, Inc. or your local distributor for assistance.

1. The P313 pump should be installed flat on a base to a maximum of a 15 degree angle of inclination to ensure optimum lubrication.

2. The inlet to the P313 pump should be sized for the flow rate of the pump with no unnecessary restrictions that can cause cavitation. Teflon tape should be used to seal all joints. If pumps are to be operated at temperatures in excess of 1600 F, it is important to insure a positive head to the pump to prevent cavitation.

3. The discharge plumbing from the pump should be properly sized to the flow rate to prevent line pressure loss to the work area. It is essential to provide a safety bypass valve between the pump and the work area to protect the pump from pressure spikes in the event of a blockage or the use of a shut-off gun.

4. Use of a dampener is necessary to minimize pulsation at drive elements, plumbing, connections, and other system areas. The use of a dampener with Giant Industries, Inc. pumps is optional, although recommended by Giant Industries, Inc. to further reduce system pulsation. Dampeners can also reduce the severity of pressure spikes that occur in systems using a shut-off gun. A dampener must be positioned downstream from the unloader.

5. When viewed from the side of the P313 pump, crankshaft rotation is clockwise on pumps with left handed shafts and counterclockwise on pumps with right handed shafts. Reverse rotation may be safely achieved by following a few guidelines available upon request from Giant Industries, Inc. Required horsepower for system operation can be obtained from the charts on pages 3-7 and 10.

6. Before beginning operation of your pumping system, remember: Check that the crankcase and seal areas have been properly lubricated per recommended schedules. Do not run the P313 pump dry for extended periods of time. Cavitation will result in severe damage. Always remember to check that all plumbing valves are open and that pumped media can flow freely to the inlet of the P313 pump.

List Price: $1,008.31
Our Price: $924.01
You save $84.30!

Availability:: available for order
Product Code: LAN-8.702-356.0
PRICE SUBJECT TO CHANGE.  PRICE VALID ON THE GIANT PRESSURE WASHER PUMP P313 – 1/09/2012

Posted on

GENERAL PRESSURE WASHER PUMP,TS1021L SERIES 47

Spotlight on GENERAL PRESSURE WASHER PUMP,TS1021L SERIES 47

The TS1021L is the  preferred pump frame in the pressure cleaning industry
• Forged brass manifold with an exclusive lifetime warranty
• Large-capacity, die-cast, anodized aluminum oil-bath crankcase
• Over-sized connecting rods for maximum life
• Heavy-duty tapered roller bearing.
• Solid ceramic plungers with continuously lubricated packings
• Unitized stainless steel inlet and discharge valves
• Available in left-handed “L” version

GENERAL PRESSURE WASHER PUMP,TS1021L SERIES 47
GENERAL PRESSURE WASHER PUMP,TS1021L SERIES 47

The GENERAL PRESSURE WASHER PUMP,TS1021L SERIES 47 Features:

  • General 47 Series Triplex Plunger Pump (left Handed)
  • Solid Shaft for Belt or Gear Drive
  • Max. Volume: 5.6 GPM
  • Max. Discharge Pressure: 1,700 PSI
  • Max. Pump Speed: 1450 RPM
  • Shaft Diameter: 24mm Solid
  • Max. Horsepower Requirements: 9.0 GHP
  • Max. Fluid Temp.: 165 degrees F.
  • Inlet Ports (2): 1/2″ BSP
  • Discharge Ports (2): 3/8″ BSP
  • Drive Side: Left
  • Forged brass head & valve covers
  • Solid ceramic plungers
  • Weight: 32.0 lb.
TS1021L Pressure Washer Pump
TS1021L Pressure Washer Pump

List Price: $1,206.90
Our Price: $631.52
You save $575.38!
Availability:: available for order
Product Code: TS1021L
PRICE SUBJECT TO CHANGE.  PRICE VALID ON THE GENERAL PRESSURE WASHER PUMP TS1021L – 1/5/2012

 

Posted on

310 CAT PUMP

Spotlight on the 310 CAT PUMP 4GPM 2200PSI.

5PFR Ceramic Plunger, 4.0/2200, 950 RPM or 5.0/1500, 1190 RPM, D-End, BBCP/S-Valves.

Need parts for this 310 CAT PUMP? Click here for the datasheet.

Click here for servicing instructions.

The 310 CAT PUMP Features:

  • Superior Design:
  • The 310 CAT PUMPS Triplex plunger design gives smoother fluid flow
  • High pressure seals are completely lubricated and cooled by the fluid being pumped
  • Inlet and discharge valve assemblies interchange for easier maintenance
  • Lubricated low pressure seal provides double protection against external leakage
  • Oil bath crankcase assures optimum lubrication
  • Close tolerance concentricity of the ceramic plunger maximizes seal life
  • Quality Materials:
  • All stainless steel valves are heat treated and seats are roller burnished for a positive seal and extended valve life
  • Brass, stainless steel, or nickel aluminum brass manifolds for strength and corrosion resistance
  • Special hardened, polished surface of solid ceramic plunger is abrasion resistant and results in extended seal life
  • Specially formulated 310 CAT PUMP exclusive, HI-Pressure seals offer unmatched performance and seal life
  • Diecast aluminum crankcase provides high strength, minimum weight and precision tolerance control
  • Chrome-moly crankshaft gives unmatched strength and surface hardness
  • Oversized crankshaft bearings with greater loading capacity mean longer bearing life
  • Easy Maintenance:
  • Wet end is easily serviced without entering crankcase, requiring less time and effort
  • Valve assemblies are accessible without disturbing piping, for quick service
  • Preset packings mean no packing gland adjustment is necessary, reducing maintenance costs
310 CAT PUMP
310 CAT PUMP

The 310 CAT PUMP has the following specifications:

  • Bore…………………………………………………………………0.787” (20 mm)
  • Crankcase Capacity……………………………………….18 oz. (0.55 l)
  • Standard Liquid Temperature……………………..160°F (71°C)
  • Above 130°F call CAT PUMPS for inlet conditions and elastomer recommendations.
  • Inlet Ports (2)…………………………………………..1/2” NPTF (1/2” NPTF)
  • Discharge Ports (2)…………………………………3/8” NPTF (3/8” NPTF)
  • Shaft Diameter…………………………………………….. 0.787” (20 mm)
  • Weight…………………………………………………………19.8 lbs. (9 kg)
  • Dimensions……………………………..11.73 x 10.0 x 5.24” (298 x 254 x 133 mm)
  • Weight of the 310 CAT PUMP: 19.8 lbs.
  • Flow …………………………………………………………….4.0 gpm (15 l/m)
  • Pressure Range………………………………100 to 2200 psi (7 to 155 bar)
  • RPM ……………………………………………………………950 rpm (950 rpm)
  • Inlet Pressure Range……………………………–5 to 60 psi (–0.35 to 4 bar)
  • Stroke ……………………………………………………………..0.709” (18 mm)
310 CAT PUMP exploded VIEW
310 CAT PUMP exploded VIEW
Lubrication: fill crankcase with CAT Pump hydraulic oil per pump specifications. DO NOT RUN PUMP WITHOUT OIL IN CRANKCASE. Change initial oil after a 50 hour break-in period, and every three months or 500 hour intervals thereafter.
List Price: $1,159.06
Our Price: $891.90 Click to order the 310 CAT Pump
Availability:: available for order
Product Code: BAPL-2798
PRICE SUBJECT TO CHANGE.  PRICE VALID ON THE 310 CAT PUMP 1/4/2012
Posted on

CAT Pressure Washer Pump 3535

Spotlight on the CAT Pressure Washer Pump 3535.

Description:
CAT Pressure Washer Pump  3535 – 35PFR Ceramic Plunger, DS, 36/1200, 800 RPM, BBCP/S-Valves.

The CAT Pressure Washer Pump 3535 Features:

  • The CAT Pump 3535 Triplex design delivers high efficiency and low pulsation.
  • Durable dual V-Packings are lubricated and cooled by pumped liquid.
  • Pre-set Lo-Pressure Seals provide secondary protection against external leaks and require no packing adjustments.
  • Special high-density, polished, concentric plungers provide a true wear surface and extended seal life.
  • Specially formulated Seals and V-Packings offer unmatched performance and extended life of the CAT Pump 3535.
  • Interchangeable inlet and discharge valves for easy servicing.
  • Wet-end easily serviced without entering crankcase.
CAT Pressure Washer Pump 3535
CAT Pressure Washer Pump 3535
CAT Pressure Washer Pump 3535 Datasheet Parts Breakdown pdf Service Manual Service manual pdf
CAT Pressure Washer Pump 3535 - exploded view
CAT Pressure Washer Pump 3535 - exploded view

The CAT Pressure Washer Pump 3535 has the following specifications:

  • Flow…………………………………………………………………36 gpm (136l/m)
  • Pressure Range……………………………………..100 to 1200 psi (7 to 85 bar)
  • Inlet Pressure Range…………………………….Flooded to 70 psi (Flooded to 4.9 bar)
  • RPM………………………………………………………………..800 rpm (800 rpm)
  • Bore…………………………………………………………………..1.575” (40 mm)
  • Stroke………………………………………………………………..1.890” (48 mm)
  • Crankcase Capacity of the CAT Pump 3535…………………………………………..4.2 Qts. (4 l)
  • Maximum Liquid Temperature ………………………………160°F (70°C)
  • Above 130°F call CAT PUMPS for inlet conditions and elastomer recommendations.
  • Inlet Ports (2)……………………………………………..1-1/2” NPTF (1-1/2 NPTF)
  • Discharge Ports (2)……………………………………………1” NPTF (1” NPTF)
  • Pulley Mounting…………………………………………….Either Side (Either Side)
  • Shaft Diameter…………………………………………………… 1.378” (35 mm)
  • CAT Pump 3535Weight……………………………………………………………..139 lbs. (63 kg)
  • Dimensions (3535, 3535C)……………….23.87 x 18.11 x 9.72” (606.5 x 460 x 247 mm)

Our Price: $6,712.00
Call 1-877-824-7763 {for a better price}
Availability:: Available for Order
Product Code: 3535
PRICE SUBJECT TO CHANGE.  PRICE VALID ON THE CAT PUMP 3535 – 12/28/2011

 

Posted on

General Pressure Washer Pump TSF2019

Spotlight on the General Pressure Washer Pump TSF2019.

General Pressure Washer Pump TSF2019,SER.66,24MM, 7.6 GPM @ 3600 PSI @ 1750 RPM, See product spec sheet for detailed specifications, repair kits and replacement parts. Click here.

General Pressure Washer Pump TSF2019
General Pressure Washer Pump TSF2019

The General Pressure Washer Pump TSF2019 Features:

  • Oversized roller bearings
  • Fully anodized crankcase
  • Innovative new seal design extends seal life on the TSF2019
  • New plunger design improves “thermal shock” resistance
  • New valve cap design improves hydrostatic performance
General Pressure Washer Pump TSF2019
General Pressure Washer Pump TSF2019

The General Pressure Washer Pump TSF2019 has the following specifications:

  • 7.6 GPM maximum
  • 3600 PSI maximum
  • 1450 RPM maximum
  • 165 F maximum temperature
  • 24mm shaft diameter
  • Inlet Port: 3/4″ FPT
  • Discharge Port: 3/8″ FPT
  • Crankcase Capacity: 31 oz
  • Weight: 40 lbs

List Price: $1,175.56
Our Price: $904.59
You save $270.97!
Availability:: available for order
Product Code: BAPL-6220

PRICE SUBJECT TO CHANGE.  PRICE VALID ON THE TSF2019 12/27/2011.

 

Posted on

General Pressure Washer Pump TS1021

Spotlight on the General Pressure Washer Pump TS1021, T SERIES 47.

Need parts for this pump? Click here for the datasheet.

The General Pressure Washer Pump TS1021 ,T SERIES 47 Features:

  • The preferred pump frame in the cleaning industry
  • The TS1021 has a Forged brass manifold with an exclusive lifetime warranty
  • Large capacity, die cast, anodized aluminum oil bath crankcase
  • Over sized connecting rods for maximum life
  • Heavy duty tapered roller bearing
  • The TS1021 Pump has solid ceramic plungers with continuously lubricating packings
  • Unitized stainless steel inlet and discharge valves
  • The TS1021 is Available in left handed “L” version
General Pressure Washer Pump TS1021
General Pressure Washer Pump TS1021

The General Pressure Washer Pump TS1021,T SERIES 47 has the following specifications:

  • Maximum Volume: 4.5/5.6 GPM
  • Maximum Discharge Pressure: 3000/1700 PSI
  • Maximum Inlet Pressure: 125 PSI
  • Maximum Pump Speed: 1125/1450 RPM
  • Minimum Horsepower Requirements: 6.5 bhp (9.8 hp for gas engines)
  • Bore: .787″ (20mm)’
  • Stroke: .630″ (16mm)
  • Crankcase Capacity: 40.6 oz. non-detergent SAE 30W oil.
  • Maximum Fluid Temperature: 165 F.
  • Inlet Port Thread: 1/2″ FPT
  • Discharge Port Thread: 3/8″ FPT
  • Shaft Diameter: .945″ (24mm)
  • Dimensions of the TS1021: 12.6″ x 8.8″ x6.9″
  • Weight: 32.0 lb.
  • Lubrication: Fill the crankcase to the dot on the oil gauge window per specifications with non-detergent SAE 30W oil. Change the oil in the TS1021 after 40 hour break-in period, then every three (3) months or 500 hour intervals thereafter
  • The following statement is intended to assist our customers in understanding the terms of General Pump’s warranty, the circumstances under which they will honor claims, and the procedure for making such claims.
  • General Pump/US warrants each pump to be free of defects in material or workmanship for a period of five (5) years from the date of shipment. In addition, General Pump/US warrants all forged brass pump manifolds to be free of defects in material and workmanship and from damage resulting from freezing for the life of the pump. Liability on this warranty is on all non-wear parts and limited to the repair or replacement of any pump returned to General Pump/US which upon inspection is judged to be defective due to workmanship or material failure.
  • In the course of marketing or servicing the customer or potential customer’s needs, General Pump/US will use its best judgment in its recommendations. However, the ultimate responsibility for product application decisions shall rest with the customer. the sole and only warranty made by General Pump/US is the limited warranty described above. General Pump/US makes no other warranty or warranties of any kind, express or implied, including any implied warranty or merchantability or of any fitness for a particular use or purpose.General Pump/US disclaims and denies any liability for any direct, indirect, special, incidental or consequential damages which may be suffered as a result of sale, delivery, servicing, use, loss of any product, downtime, labor, freight or other charges not expressly included herein. the only liability and the total liability of General Pump/US under this limited warranty or in any claim regarding or involving General Pump/US is expressly limited to the replacement of or purchase price of the product.
  • The following items are NOT warranted, due to matters beyond General Pump/US control. Normal wear and tear to parts that are considered standard wear parts. Defects caused by the fault or negligence of the buyer or third party. Use of unauthorized repair parts, or; modifications made to the TS1021 by the customer.

List Price: $724.64
Our Price: $557.61
You save $167.03!
Availability:: available for order
Product Code: BAPL-1989
PRICE SUBJECT TO CHANGE.  PRICE VALID ON THE TS1021 GENERAL PRESSURE WASHER PUMP 12/22/2011

Posted on

COMET PUMP LWD 2010 S – 6303.0306.00

Spotlight on the Pressure Washer COMET PUMP LWD 2010 S – 6303.0306.00.

COMET PUMP LWD 2010 S PART NO. 6303.0306.00, 2.0 GPM @ 1000 PSI @ 3400 RPM, See product spec sheet for detailed specifications, repair kits and replacement parts.
Click here.
Repair Manual Click here

Pressure Washer COMET PUMP LWD 2010 S – 6303.0306.00 Features:

  • 1/2″ FPT Inlet, 3/8″ FPT Discharge
  • Anodized, Die-Cast Aluminum Crankcase
  • Solid Ceramic Plungers
  • Stainless Steel Check Valves & Piston Guides
  • Buna-Textile V-Packings
  • Reversible Crankcase for Right or Left Hand Mounting
  • 24mm Solid, Keyed Shaft
Pressure Washer COMET PUMP LWD 2010 S - 6303.0306.00
Pressure Washer COMET PUMP LWD 2010 S - 6303.0306.00

Pressure Washer COMET PUMP LWD 2010 S – 6303.0306.00 Technical Specifications:

  • GPM 2.2
  • PSI 1000
  • RPM 3400
  • SHAFT 24mm Solid
  • PISTON 15mm
  • WT. 10.4
Pressure Washer COMET PUMP LWD 2010 S - 6303.0306.00 Features:
Pressure Washer COMET PUMP LWD 2010 S - 6303.0306.00 Features:

 

List Price: $385.00
Our Price: $237.01 
You save $147.99!

Availability:: available for order
Product Code: 6303.0306.00
PRICE SUBJECT TO CHANGE.  PRICE VALID ON THE LWD 2010 S 12/21/2011

Posted on

Annovi reverberi Pressure Washer Pump RMW2.5G25D

Annovi reverberi Pressure Washer Pump RMW2.5G25D 2.5 GPM @ 2500 PSI, Axial Radial pumps that fit many 5 and 5-1/2 hp engines. See link for product details and replacement parts: RMW PARTS LIST

Will this Annovi reverberi Pressure Washer Pump RMW2.5G25D line up correctly with your machine?
Click here to view dimensions (in mm).

This plunger pump will pump up to 2.5 GPM at 2500 PSI. It spins at 3400 RPM in a direct drive system coupled with a gasoline engine. The matching flange provides convenient connection to most 7/8” shaft 1.1 – 5.5 HP engines. The hollow shafted pump includes a built-in pressure control valve, and chemical injection system.

We do not have any mfg cross reference information available. However, RMW pumps fit most vertical engines (pump under the motor) with a 7/8″ straight keyed shaft.

Annovi reverberi Pressure Washer Pump RMW2.5G25D pumps have a standard 22mm-14 twist connect outlet.

Best to choose RMW pump that has same or close to original pumps GPM & PSI. Significant changes to GPM may cause nozzle & motor problems.

Features of this Annovi reverberi Pressure Washer Pump RMW2.5G25D:

  • SKU: RMW2.5G25D
  • Brand: Annovi Reverberi – AR North America
  • AR RMW25G25D, RMW2.5G25D Vertical Radial-Axial series replacement pump (Mounts under the engine)
  • Fits most homeowner type vertical pressure washers with Front Mounted Pump (see 2nd image)
  • NOTE: This Pump DOES NOT fit Karcher units using a hex head bolt to drive the pump.
  • Built In unloader and chemical injector
  • Brass manifold
  • Stainless steel plungers
  • Pump comes with oil
  • Manifold: Forged brass for long term use.
  • Bolts: Three 6mm cadmium plated steel.
  • Plungers: Hardened stainless steel.
  • Valves: Stainless steel poppet, seat and cage, stainless steel spring.
  • Seals: Buna-N dual seals.
  • Bearings: Premium oversized ball and needle bearings.
  • Crankshaft: Precision die-cast, with cooling fins for maximum heat dissipation. The housing retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer
Annovi reverberi Pressure Washer Pump RMW2.5G25D
Annovi reverberi Pressure Washer Pump RMW2.5G25D

The Technical specifications of the Annovi reverberi Pressure Washer Pump RMW2.5G25D:

  • Vertical Mount with Gas Flange 3-6 HP
  • Max. Volume: 2.5 GPM
  • Max. Discharge Pressure: 2,500 PSI
  • Max. Pump Speed: 3,400 RPM
  • Shaft Diameter: 7/8” Hollow
  • Engine shafts longer than 2” will require spacers or washers
  • Maximum Horsepower Requirements: 5.8 GHP
  • Inlet Port: 3/4″ FGH (garden hose)
  • Outlet Port: 22mm (Twist Connect)
  • Weight: 7.7 lb
Annovi reverberi Pressure Washer Pump RMW2.5G25D
Annovi reverberi Pressure Washer Pump RMW2.5G25D

List Price: $307.66
Our Price: $196.39
You save $111.27!
Availability:: available for order
Product Code: RMW2.5G25D

PRICE SUBJECT TO CHANGE.  PRICE VALID ON THIS RMW2.5G25D 12/20/2011.

Posted on

CAT Pump 2DX20ES Pressure Washer Plunger Pump

Spotlight on the CAT Pump 2DX20ES Pressure Washer Plunger Pump.

The Features of the CAT Pump 2DX20ES Pressure Washer Plunger Pump are:

  • 2DX20ES Triplex plunger design provides a smooth liquid flow.
  • Specially formulated Hi-Pressure Seals and concentric solid ceramic plungers assure true wear surface and extended seal life.
  • Ultimate compact, direct-drive unit for maximum portability.
  • Integral Regulating Unloader with built-in by-pass standard on all units to assure system pressure control and pump protection.
  • Fixed chemical injector standard on all units,offers cleaning flexibility.
  • Stacked valve design for ease in servicing.
  • Swivel garden hose fitting with filter screen for easy inlet connection.
2DX20ES Datasheet Data Sheet Service Manual Service Manual

Technical Specifications of the CAT Pump 2DX20ES Pressure Washer Plunger Pump are:

  • Flow ……………………………………………………….2.0 GPM (7.6 L/M)
  • Max. Discharge Pressure …………………………2000 PSI (140 BAR)
  • RPM…………………………………………………….3450 RPM (3450 RPM)
  • Stroke ………………………………………………………..0.157″ (4.0 mm)
  • Shaft Diameter………………………………………………..5/8″ (15.8 mm)
  • Inlet Pressure Range…………………..Flooded to 60 PSI (Flooded to 4 Bar)
  • Bore …………………………………………………………..0.630″ (16 mm)
  • Max. Liquid Temperature ………………………………140°F (60°C)
  • Above 130°F call CAT PUMPS for inlet conditions and elastomer recommendations.
  • Crankcase Capacity…………………………………….8.5 oz. (0.25 L)
  • Inlet Ports (1) ……………………………………………3/4″ GH (3/4″ GH)
  • Discharge Port (1) …………………………………3/8″ NPTM (3/8″ NPTM)
  • Chemical Injection Barb………………………….8/32″ UNF (8/32″ UNF)
  • Weight …………………………………………………….10.7 lbs. (4.9 kg)
  • Dimensions ………………………………..7.99 x 7.75 x 6.29″ (203 x 197 x 160 mm)
CAT Pump 2DX20ES Pressure Washer Plunger Pump
CAT Pump 2DX20ES Pressure Washer Plunger Pump

 

CAT Pump 2DX20ES Pressure Washer Plunger Pump (Breakdown)
CAT Pump 2DX20ES Pressure Washer Plunger Pump (Breakdown)

Our Price: $663.00
Call 1-877-824-7763 {Smart Phones Click to Call} for a better price…
Availability:: Available for Order
Product Code: 2DX20ES
PRICE SUBJECT TO CHANGE.  PRICE VALID ON THE CAT PUMP 2DX20ES 12/19/2011

 

Posted on

CAT Pump 5CP2150W Ceramic Pressure Washer Plunger Pump

Spotlight on the CAT Pump 5CP2150W Ceramic Pressure Washer Plunger Pump.

The CAT Pump 5CP2150W Ceramic Pressure Washer Plunger Pump Features:

  • Triplex design offers high efficiency and low pulsation.
  • Durable high pressure seals are lubricated and cooled by pumped liquid.
  • Pre-set Lo-Pressure Seals provide secondary protection against external leaks and require no packing adjustment.
  • Special high density, polished, concentric plungers provide a true wear surface and extended seal life.
  • Optional STHT, FPM and EPDM elastomers for compatibility with many liquids and temperatures up to 200°F.
  • Wet-end easily serviced without entering crankcase.

The CAT Pump 5CP2150W Ceramic Pressure Washer Plunger Pump has the following specifications:

  • Inlet Pressure Range (950 rpm)……………– 5 to 60 psi (– 0.35 to 4 bar)
  • Inlet Pressure Range (1725 rpm)…..Flooded to 60 psi (Flooded to 4 bar)
  • Crankcase Capacity……………………………………………17 oz. (0.51 l)
  • Standard Liquid Temperature…………………………160°F (71°C)
  • Above 130°F call Cat Pumps for inlet conditions and elastomer recommendations.
  • Inlet Ports (2)……………………………………………….1/2” NPTF (1/2” NPTF)
  • Discharge Ports (2)……………………………………..3/8” NPTF (3/8” NPTF)
  • Shaft Diameter………………………………………………….0.787” (20 mm)
  • Dimensions…………………………………10.35 x 10.0 x 5.78” (263 x 254 x 147)
  • MODEL 5CP2120W Belt-Drive
  • Flow………………………………………………………………………………4.0 gpm (15 lpm)
  • Pressure Range ……………………………………………………100-2500 psi (7-175 bar)
  • RPM ……………………………………………………………………………..950 rpm (950 rpm)
  • Bore………………………………………………………………………………….0.787” (20 mm)
  • Stroke……………………………………………………………………………….0.709” (18 mm)
  • Weight………………………………………………………………………..19.14 lbs. (8.7 kg)
  • MODEL 5CP2150W Direct-Drive
  • Flow………………………………………………………………………………5.0 gpm (19 lpm)
  • Pressure Range ……………………………………………………100-2000 psi (7-140 bar)
  • RPM …………………………………………………………………………..1725 rpm (1725 rpm)
  • Bore………………………………………………………………………………….0.787” (20 mm)
  • Stroke……………………………………………………………………………….0.472” (12 mm)
  • Weight………………………………………………………………………..19.14 lbs. (8.7 kg)
CAT Pump 5CP2150W Ceramic Pressure Washer Plunger Pump
CAT Pump 5CP2150W Ceramic Pressure Washer Plunger Pump
5CP2120W Datasheet Data Sheet Service Manual Service Manual

 

CAT Pump 5CP2150W Ceramic Pressure Washer Plunger Pump
CAT Pump 5CP2150W Ceramic Pressure Washer Plunger Pump

List Price: $1,273.00
Our Price: $1,273.00
Availability:: Available for Order
Product Code: 5CP2150W
CAT Pressure Washer Pump
PRICE SUBJECT TO CHANGE.  PRICE VALID ON THE 5CP2150W 12/16/2011.