Craig Schuster Web / SEO Manager

October 4, 2011October 25, 2011

General Pump Stainless Steel Check Valve YCV38FSS

General Pump Stainless Steel Check Valve YCV38FSS – 3/8″F-NPT

Click here for the General Pump Stainless Steel Check Valve YCV38FSS parts list.

General Pump Stainless Steel Ckeck Valve YCV38FSS

The General Pump Stainless Steel Check Valve YCV38FSS Features:

General Pump Stainless Steel Check Valve
10.5 gpm
Rated pressure: 5800 psi, max. 6500psi
3/8″ inlet

List Price: $57.10
Our Price: $43.94
You save $13.16!
Availability:: available for order
Product Code: YCV38FSS
Price subject to change – Valid 10/4/2011

October 4, 2011October 25, 2011

COMET PRESSURE WASHER PUMP AXD 2020 E – 6501.0010.00

The COMET PUMP AXD 2020 E PART NO. 6501.0010.00, has 1.9 GPM @ 2000 PSI @ 3400 RPM. To see product spec sheet for detailed specifications, repair kits and replacement parts for the COMET PRESSURE WASHER PUMP AXD 2020 E – 6501.0010.00. Click here.

The COMET PRESSURE WASHER PUMP AXD 2020 E – 6501.0010.00 Features:

3400 RPM – 5/8″ Hollow Shaft
3/4″ FGH Inlet – 3/8″ MPT Outlet
Built-in Uniflow Unloader and Chemical Injector
Ceramic Plungers
Built-in Garden Hose Adapter
Industrial Duty Construction for Extended Life
Optional Built-in Thermal Protector & Pressure Relief
Stainless Steel Check Valves
Forged Brass Manifold
Patent Registered Ball Bearing Design
NEMA 56C Electric Motor Flange

Comet Pressure Washer Pump AXD 2020 E 6501.0010.00 exploded view

The COMET PRESSURE WASHER PUMP AXD 2020 E – 6501.0010.00 has the following specifications:

Maximum Volume 1.9 gpm
Max. Discharge Pressure 2000 psi
Maximum Pump Speed 3400 rpm
Inlet Port Thread 3/4 FGH
Discharge Port Thread 3/8 MPT
Shaft Diameter 5/8 Hollow
Weight 12.0 lbs.

List Price: $580.00
Our Price: $293.64
You save $286.36!
Availability:: available for order
Product Code: 6501.0010.00
Comet Pressure Washer Pump
PRICE SUBJECT TO CHANGE – VALID AS OF 10/4/2011

October 3, 2011October 25, 2011

AR Annovi Reverberi Pressure Washer Pump – RMW2G24

The AR Annovi Reverberi Pressure Washer Pump – RMW2G24 is the Vertical Shaft Replacement Pump!
Inlet & Outlet come out in the FRONT of the engine (spark plug end). Most pressure washer pumps are only designed to last for approximately 50 hours of use. This Annovi Reverberi Pump RMW2G24 is designed to last for 300 + hours of use.

IT’S IMPORTANT TO NOTE:
Depending on your Pressure Washer model, you may need to get three new mounting bolts to mount the Annovi Reverberi Pump RMW2G24 to the engine. In this case, your local hardware store will carry these bolts. There are too many different Pressure Washer models and bolt size combinations so we cannot provide new bolts for the replacement pump.
Below are the most common bolt sizes needed to mount your new replacement Annovi Reverberi Pressure Washer Pump – RMW2G24 to the engine:
– 5/16″ 18 x 2 1/2″ (Qty. 2)
– 5/16″ 18 x 3 1/2″ (Qty. 1)

The Annovi Reverberi Pressure Washer Pump – RMW2G24 Features:

7/8″ hollow shaft
operates at 3400 RPM
max PSI of 2400
Manifold is made from precision die cast aluminum with a special anti-corrosion finish.

The Annovi Reverberi Pressure Washer Pump – RMW2G24 has the following specifications:

Max Flow (in GPM): 2.0
Max Flow (in L/Min): 7.6
Max Pressure (in PSI): 2400
Max Bar: 166
Power EBHP: 3.2
Bore Dia: 12mm
Stroke: 8.3mm
Crankshaft ID Stamp: 5
Pump Speed (in RPM): 3400
Shaft Diameter: 7/8″ hollow

List Price: $243.26
Our Price: $156.74
You save $86.52!

Availability:: available for order
Product Code: RMW2G24
Annovi Reverberi Pressure Washer Pump

October 3, 2011October 25, 2011

Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH

This Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH has the following Frame: Powder coated steel frame, handle and tank · Heavy-duty tires for easy mobility · Front foot brace · Rugged steel body

The Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH Burners: Stainless-steel combustion chamber · Direct spark ignition

These Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH Motors have: Heavy-duty, high quality cast aluminum electric motor

The Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH has the following Components: Safety switch prevents overheating · Thermostatically controlled · Suitable for air ducting · Easy to operate controls · High capacity fuel tank · Electronic flame control · Automatic ignition · Water resistant control box · Automatic fuel shut-off · High thermal efficiency · Control panel with thermostat plug, reset push button and safety air pressure switch · High pressure fuel pump · Vacuum sensor helps prevent heater lock out · Heated fuel filter for more reliable starts in subzero temperatures

The Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH will Function on: Kerosene or No. 1 and No. 2 fuel oil.

The Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH is for use on construction sites and applications where the heat will be ducted into a building.

The MH-0125-0MIH Specifications subject to change without notice. Use in accordance with any and all state or local codes, regulations, and/or ordinances.

Please see heater “Owner’s Manual” included with each MH-0125-0MIH for a complete list of important safety information.

Important Notes about the MH-0125-0MIH:
· Not for use in residential living areas or inadequately ventilated areas.
· Proper ventilation required during operation.
· Must be plugged into an approved standard electrical outlet for operation.

View Product Information Sheet for Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH

The MH-0125-0MIH has the following technical specifications:

Heat Output 125,000 BTU
Temperature Rise 130°F
Max. Output Temperature 240°F
Heated Air Output 1,180 CFM
Power Consumption 460 watts
AC Power 115 Volts/60Hz/1Ø/7.0 Amp
Fan Static Pressure 0.7-inch WC
Fuel Consumption 0.9 gal./hr.
Fuel Tank Capacity 13.5 gallons
Max. Operating Hours 15 hours
Duct Size (LxDiameter) 25 ft.x12in.
Net Weight 154 lbs.
Shipping Weight 162 lbs.
Length 54.8 in.
Width 27.6 in.
Height 32.7 in.

List Price: $2,670.00
Our Price: $2,269.50
You save $400.50!
Availability:: available for order
Product Code: MH-0125-0MIH
Mi-T-M Portable Heater

September 30, 2011October 25, 2011

Mi-T-M Portable Heater Propane Directional – MH-0175-0MDH

The MH-0175-0MDH Outer Casing/Design: Rugged design · Durable powder coated outer casing and side lifting handles · Lifting handles for easy loading and unloading · The unit is naturally balance to lift easily with handles · Two 10-inch solid rubber tires for mobility and easy placement

This MH-0175-0MDH has the following Components: Independent fan and burner controls for simple operation · Thermostat control with 20-foot cord allows for a consistent, comfortable environment and use in remote locations · 15-foot hose and regulator assembly · Air flow safety devices · Totally enclosed frame · Fully enclosed electronics · Electronic ignition · Operates as both a fresh air circulator or a heater at the touch of a switch · Super quiet, super efficient · Easy to set-up · Numerous duct options available · Direct spark ignition

The Mi-T-M Portable Heater Propane Directional – MH-0175-0MDH is intended for use in tent and party applications or construction sites.

Specifications on the Mi-T-M Portable Heater Propane Directional – MH-0175-0MDH subject to change without notice. Use in accordance with any and all state or local codes, regulations, and/or ordinances.

Please see heater “Owner’s Manual” included with each heater for a complete list of important safety information.

Important Notes:
· Not for use in residential living areas or inadequately ventilated areas.
· Proper ventilation required during operation.
· Extremely hot during operation. Keep children, animals and all combustible objects away from heater.

View Product Information Sheet for Mi-T-M Portable Heater Propane Directional – MH-0175-0MDH

The Mi-T-M Portable Heater Propane Directional MH-0175-0MDH has the following specifications:

Heat Output 175,000 BTU
Type Propane
Heated Air Output 1,200 CFM
Fuel Consumption 8.75 lbs./hr.
Inlet Gas Pressure 11-inch WC
Temperature Rise (above ambient) 140°F
Suggested Tank Size 100 lbs.
Electrical Requirements 115 Volts/60Hz/1Ø
Amps (Starting/Cont.) 8.4 / 3.6 Amps
Net Weight 164 lbs.
Shipping Weight 193 lbs.
Length 30.62 in.
Width 18.25 in.
Height 31.12 in.

List Price: $2,465.00
Our Price: $2,095.25
You save $369.75
Availability:: available for order
Product Code: MH-0175-0MDH
Mi-T-M Portable Heater

September 30, 2011October 26, 2011

CAT Pump 8058 Direct Drive Gearbox

CAT Pump 8058 Direct Drive Gearbox Helical -1-1/8″ Shaft, Gearbox Pump: 51G118, 58G118 Used on Models 51 and 58 Pump.

The CAT Pump 8058 Direct Drive Gearbox Features:

Polished solid ceramic plungers last long and resist abrasion.
Triplex plunger design providing low pulsation and quiet operation.
Internally lubricated and cooled packings for extended life.
No pulley selection or adjustment for quick, easy gas engine mounting.
Totally sealed housing providing independent
gearbox lubrication for maximum service life. Hardened steel helical design gears for smooth, quiet operation.
Multiple engine shaft and flange options for flexibility.

The CAT Pump 8058 Direct Drive Gearbox has the following specifications:

Gear Ratio ………………………… 2.0384 to 1 (2.0384 to 1)
Mounting Face…………………… 6-1/2″ (165 mm)
Engine Shaft Diameter……………………………………….. 1″ (25.4 mm)……………………………………….. 1-1/8″ ( 28.5 mm)
Engine Shaft Length…………… 3-1/4″ (82.6 mm)
Gearbox Capacity………………. 10 oz. (0.30 L)
Weight 8051, 8058, 8061, 8065, 8068…. 4.2 lbs. (1.90 kg) 8071, 8078 ………………………… 7.5 lbs. (3.40 kg)
Dimensions……………………….. 6.42 x 4.53 x8.19″ (163x115x208 mm)
Flow…………………………………. 5.0 GPM (19 L/M)
Pressure Range ………………… 100 to 2500 PSI (7 to 175 BAR)
Inlet Pressure Range………….. Flooded to 60 PSI (Flooded to 4 BAR)
Maximum Pump RPM…………. 1570 RPM (1570 RPM)
Maximum Engine RPM……….. 3200 RPM (3200 RPM)
Bore…………………………………. 0.708″ (18 mm)
Horsepower-Electric …………… 8.6 HP (8.6 HP)
Stroke ………………………………. 0.669″ (17 mm)
Pump Crankcase Capacity….. 25 oz. (0.75 L)
Weight ……………………………… 30.7 lbs. (13.9 kg)
Dimensions with .B…………….. 13.58 x 10.75 x 8.19″ (345 x 273 x 208 mm)
See Models 53, 58, 55, 51 data sheet for pump information.

CAT Pump 8085 Direct Drive Gearbox - Exploded Parts View

List Price: $685.00
Our Price: $685.00
Sale Price: $600.00
You save $85.00!

Availability:: available for order
Product Code: 8058

SERVICING THE CAT Pump 8058 Direct Drive Gearbox DIS-ASSEMBLY
1. Completely drain lube from the direct drive gearbox housing.
2. Remove the four HHC screws which fasten the direct drive gearbox to the engine and separate gearbox and pump from engine.
3. Remove the four HHC screws which fasten the direct drive gearbox to the bearing cover flange and separate gearbox housing from pump.
4. Place gearbox housing on work surface with seal facing up.
5. Remove pinion oil seal by inserting screwdriver between pinion gear and inner lip of seal and pry out. Seal will be damaged and must be replaced.
6. Remove large retaining ring in groove below the pinion oil seal using retaining ring pliers and set aside for re-use.
7. Remove the pinion gear and bearing. Turn direct drive gearbox housing over onto engine mount flange surface. Bearing is pressed into position so it is necessary to press pinion and bearing out from rear. Set gearbox housing aside.
8. Remove bearing from pinion gear. Using reverse pliers remove retaining ring from groove on pinion gear and press bearing from pinion. Set aside pinion, bearing and retaining ring.
9. Remove hex machined retaining screw, lockwasher and flat holding washer from center of helical drive gear on pump shaft.
10. Slip helical drive gear from crankshaft.
11. Remove key from keyway in pump crankshaft. At this point the direct drive gearbox has been disassembled. Now begin examination of the gearbox parts for wear and reassembly. While the gearbox is in this state of disassemble, it is advisable to examine your pump for any indication of drive-end wear. If any of the following conditions are present, removal of the bearing cover flange is necessary. Only trained technicians should service drive end.
– Leakage between bearing cover flange and pump crankcase.
-Evidence of water in pump crankcase.
-Evidence of water in gearbox crankcase.
NOTE: If removal of bearing cover flange is necessary, completely drain oil from crankcase of pump.REMOVING BEARING COVER FLANGE
1. Remove the HSH screws, lockwashers and washers from bearing cover flange.
2. Tap flange with soft mallet to separate from pump crankcase.
3. Examine pump bearing and replace if worn.
4. Examine oil seal in bearing cover flange and replace if worn.
5. Examine gasket on outside of bearing cover flange and replace if cut or cracked.
6. Examine o-ring on inside outer groove of bearing cover flange and replace if cut or worn. If further pump servicing is needed, refer to your pump service manual, and Tech Bulletin 035 on “Servicing Crankcase Section”.REPLACING BEARING COVER FLANGE
1. Line up the four holes and mount gasket on outside of bearing cover flange. Note: Models 56, 59, 60 and 70 have dual bearings and eight screws.
2. Press new seal into bearing cover flange after exercising caution not to cut seal on keyway edge.
3. Line up the inside mounting holes on bearing cover flange with the holes on the pump. Keep the two outer “flanged” mounting holes to the top rear and lower front.
4. Apply Loctite-242 to the threaded area of screws before replacing. Torque per chart.REASSEMBLY of the CAT Pump 8058 Direct Drive Gearbox
1. Insert key into pump crankshaft keyway until flush with end of shaft.
2. Examine helical drive gear teeth for wear and replace if necessary. Line up keyway on gear with pump shaft keyway and key and slide onto shaft.
3. Install flat holding washer, lockwasher and retaining screw onto shaft and torque per chart.
4. Examine gearbox oil gauge and oil drain plug for any evidence of leaking and replace o-ring and gasket if necessary.
5. Examine pinion bearing for wear and replace if necessary.
6. Examine pinion gear teeth for wear and replace if necessary.
7. Press bearing over pinion gear until seated on shoulder. (Models with dual bearings; press first bearing on until seated; then second bearing until seated up to first bearing.)
8. Install retaining ring on pinion gear and snap into groove.
9. Insert pinion and gear assembly into gearbox housing and press into position until seated on shoulder. Groove for large retaining ring must be visible.
10. Insert large retaining ring into pinion bearing housing and snap into groove.
11. Lubricate I.D. and O.D. of new pinion oil seal. Place oil seal at mouth of pinion bearing housing with garter spring facing down. Carefully press seal into position until seated on retaining ring. Keep seal square in position to avoid inner lip hanging up on pinion gear edge.
12. Rotate pinion gear so keyway is up. Mount assembled gearbox housing onto pump shaft with helical drive gear. NOTE: Carefully match gear teeth and line up mounting holes. Place engine mounting flange in forward position.
13. Install the screws to fasten gearbox to bearing cover flange. Torque per chart.MOUNTING the CAT Pump 8058 Direct Drive Gearbox ONTO ENGINE
1. Rotate crankshaft of engine until keyway is at top.
2. Insert key into keyway and generously apply Loctite 76764 antiseize lubricant to engine shaft.
3. Line up keyway of pinion gear and engine shaft and carefully slip gearbox onto engine shaft until flush with engine face. Install four hex machined screws. Torque per chart. NOTE: Due to varying engine shaft lengths it may be necessary to install a small spacer on each of the four (4) hex machined screws between gearbox flange and engine face.
4. Before starting operation, fill gearbox housing to oil gauge dot with 80-90 weight gear lube and fill crankcase of pump to oil gauge dot with CAT PUMPS Special Premium Grade Non-detergent Oil.FIELD CONVERSION FROM STANDARD PUMP
To convert from a standard pump to a direct drive gearbox pump, remove the existing bearing cover, gasket and four combination head screws. Replace with new direct drive gearbox bearing cover flange, gasket, four lockwashers and new hex socket flat head screws. The bearing for the 51, 56, 58, 59 and 60 pumps is a tapered roller bearing with outer race. Remove the standard bearing cover from the pump. Remove outer race from bearing cover by gently pounding on work surface to unseat. Then use a bearing puller tool to pull race from bearing cover. Next press outer race into gearbox bearing cover flange. Be certain race is completely seated in flange before mounting onto pump.

September 29, 2011October 25, 2011

CAT Pump 1057 – Pressure Washer Pump

Nickel Aluminum Bronze Model CAT Pump 1057

This CAT Pump 1057 Features:

Triplex plunger design provides smoother liquid flow.
V-Packings are completely lubricated and cooled by the liquid being pumped.
Special ported inlet manifold permits an external flush liquid providing cooling for hi-temp liquids and lubrication for low lubricity liquids.
Lubricated Lo-Pressure Seals provide double protection against external leakage.
Oil bath crankcase assures optimum lubrication.
Close tolerance concentricity of the ceramic plunger offers perfect alignment and maximizes seal life.
Precision design 304 and 316 stainless steel valves and seats are hardened and polished for ultimate seating and extended valve life.
Brass, Stainless Steel, Duplex SS or Nickel Aluminum Bronze manifolds for strength and corrosion resistance.
Special concentric, high-density, polished, solid ceramic plungers
provide a true wear surface and extended seal life.
Specially formulated, CAT PUMP exclusive, V-Packings offers unmatched performance and seal life.
Die cast aluminum crankcase provides high strength, minimum weight and precision tolerance control.
Chrome-moly crankshaft gives unmatched strength and surface hardness.
Oversized crankshaft bearings with greater loading capacity mean longer bearing life.
Wet-end easily serviced without entering crankcase.
Valve assemblies are accessible without disturbing piping.
Interchangeable inlet and discharge valve assemblies.
Preset seals require no packing adjustment.

CAT Pump 1057 Pressure Washer Pump Parts Breakdown PDF click here.

To get the service manual for this CAT Pump 1057 pressure washer pump click here.

This CAT Pump 1057 has the following Specifications:

Bore…………………………………………………………….0.945” (24 mm)
Stroke………………………………………………………….1.180” (30 mm)
Crankcase Capacity……………………………………….42 oz. (1.26 l)
Inlet Ports (2)…………………………………………..3/4” NPTF (3/4” NPTF)
Flushing Ports (2) (1051C)…………………………1/8” NPTF (1/8” NPTF)
Discharge Ports (2)…………………………………..1/2” NPTF (1/2” NPTF)
Pulley Mounting……………………………………… Either Side (Either Side)
Shaft Diameter………………………………………………1.181” (30 mm)
Weight…………………………………………………………44 lbs. (20 kg)
Dimensions………………………………16.28 x 12.99 x 6.44” (414 x 330 x 164 mm)
Flow………………………………………………………….. 10 gpm (38 l/m)
Pressure Range………………………………. 100 to 2200 psi (7 to 155 bar)
RPM……………………………………………………….. 958 RPM (958 RPM)
Inlet Pressure Range…………………………….. –5 to 60 psi (–0.35 to 4 bar)
Maximum Liquid Temperature ………………………..160°F (70°C)
Above 130°F call CAT PUMPS for inlet conditions and elastomer recommendations.

Our Price: $4,862.00
Call 1-877-824-7763 for a better price
Availability:: available for order
Product Code: 1057
CAT Pressure Washer Pump

September 28, 2011October 20, 2011

Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10

The Frame of the Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10 has Rugged steel body · Extension cord wrap · Powder coated hood and fuel tank · Powder coated steel handles for easy lifting · 13-inch pneumatic tires · Spare parts storage system (located on back of unit) · Fuel drain plug

The Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10 has a Burner Head with : Clamped hoses · Secured photo cell · 1-piece cast aluminum · Secured fully insulated ignition connection

The Motor of the Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10 is: Heavy-duty, high quality cast aluminum enclosed electric motor

Components for the Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10 are: Built-in temperature control thermostat with control dial · High performance fan · Power switch · Secured internal components · Integral overheat and flame-out safety · Fuel gauge · Oversized fuel cap · High limit temperature shut-off · Sure start ignition for cold temperature starts · Dual connector ignitor · Error indicator read-out

The Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10 was Factory tested for multiple fuels: Kerosene, JP8/Jet A fuel, No. 1 or No. 2 fuel oil and No. 1 or No. 2 diesel fuel

For use in workshops, garages, construction sites and farms with proper ventilation.

The Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10 has the following technical specifications:

Heat Output 400,000 BTU
Hot-Air Flow 1,400 CFM
AC Power 120 Volt/60Hz/2.8 Amp
Motor Size 1/2 HP
Air Pump Pressure 125 PSI
Fuel Tank Capacity 24.0 gallons
Fuel Consumption 3.05 gal./hr.
Max. Operating Hours 8.0 hours
Heating Area 10,000 sq ft.
Multi-Fuel Capable Yes
Net Weight 143 lbs.
Shipping Weight 152 lbs.
Length 58 in.
Width 30 in.
Height 25 in.

List Price: $2,215.00
Our Price: $1,882.75
You save $332.25!

Availability:: available for order
Product Code: MH-0400-0M10
Mi-T-M Portable Heater

September 28, 2011October 20, 2011

AR Annovi Reverberi Pump RRV4G36D-F24 – Pressure Washer Pump

These new Annovi Reverberi Pressure Washer Pumps – RRV4G36D-F24 feature a new rod design, large side cover sight glass, ceramic plungers, high quality high pressure seals, new, low-pressure seal with scraper (patented), two piece plunger guides, forged brass high efficiency head design and new styling. Flows to 5.5 GPM, Pressure to 3600 PSI, RPM 1450, 1750 & 3400. The pumps come in three drive types: 24mm solid, 1” and 1-1/8” hollow shaft. Drivers: electric, gasoline, hydraulic or diesel.

The Annovi Reverberi RRV4G36D-F24 – Pressure Washer Pump Features:

Manifold: High strength forged brass for long term use.
Bolts: Eight 6mm.
Plungers: NEW Ceramic Plungers, thicker wall to help prevent thermal shock.
Valves: Stainless Steel, valve seat o-ring is side mounted.
Seals: High quality high pressure seals. NEW low-pressure seal with a built in scraper.
Piston Guides: Two piece piston guides.
Drive End: NEW connecting rod with 12% more load surface.
Large side cover sight glass, oversized bearing. Rear cover oil drain.
Crankshaft: Forged, precision ground.

The Annovi Reverberi RRV4G36D-F24 – Pressure Washer Pump has the following technical specifications:

Max GPM……………… 4.0
Max LMP………………………… 15.1
Max PSI…………………. 3600
Max Bar…………………………. 248
Power EBHP…………… 9.9
Bore Dia. mm……………………. 15
Stroke mm………………. 9.2
Weight Lbs……………………….. 18
Max Temp………………. 140°
Oil Capacity……………………… 13.35oz
Inlet Thread …………… 1/2”F
Discharge Thread………………. 3/8”F

List Price: $576.80
Our Price: $362.08
You save $214.72!

Availability:: available for order
Product Code: RRV4G36D-F24
AR Pressure Washer Pump

September 27, 2011October 20, 2011

SUNTEC FUEL PUMP – A2VD-7119

SUNTEC FUEL PUMP – A2VD-7119, Rotation and Nozzle Location as Viewed from Shaft End: LH-RH, 3450 RPM Speed, Nozzle Capacity at Rated PSI (GPH): 3, Rated Pressure: 100.

This SUNTEC FUEL PUMP – A2VD-7119 Features:

Contamination resistant control valve
No leak easy flow bleed valve
High contact ratio precision matched gears for long life
Double-lip shaft seal
Original diaphragm/cone valve
Involute tooth-form gears for quiet operation
Two-stage units for high lift application
Factory set at 100 PSI Pressure adjustable from 100 to 200 PSI @ 3450 RPM, 100 to 200 PSI @ 1725 RPM
Lift or gravity feed applications with 10 PSI maximum inlet/return pressure
Suitable for No. 1 and No. 2 fuel oil or kerosene
May be mounted in any position, except upside down
L86-145 through L86-148 are for installations requiring up to 6″ HG vacuum single pipe and 12″ HG vacuum two pipe
L86-149 and L86-150 are rated to 17″ HG vacuum two pipe

The SUNTEC FUEL PUMP – A2VD-7119 has the following specifications:

Stages Single
Strainer & Nozzle Rating @ 100 PSI 3 GPH
Nozzle Port Location RH
RPM 3450
Rot. LH
Shipping Weight 3.50
Shipping Width 4.30
Shipping Length 4.40
Shipping Height 5.30

List Price: $108.46
Our Price: $100.00
You save $8.46!
Availability:: available for order
Product Code: A2VD-7119