Craig Schuster Web / SEO Manager

September 23, 2011October 20, 2011

Mi-T-M Portable Heater Kerosene Radiant – MH-0125-1M1R

Mi-T-M kerosene radiant portable heaters maximize radiant output for natural and soothing warmth. These portable heaters will keep you comfortable even with lower air temperatures, whether it is used indoors or outdoors.

This portable heater features a fully enclosed motor, ultra-quiet fuel pump, easily accessible power switch, electronic controls, error indicator light, accessory electrical outlet, overheat and flame-out safety feature, contractor-grade fuel cap, powder-coated fuel tank with fuel gauge, and more.

Mi-T-M Portable Heater Kerosene Radiant – MH-0125-1M1R

Frame: Compact design · Two tires for easy mobility · Easy-lift handle for portability at home or on the job site · Heat safety grille

Motor: Fully enclosed motor for longer life

Heat Output: Adjustable heat height · Clean, quiet, instant radiant heat

Components: Ultra quiet fuel pump · Power switch · Electronic controls · Error indicator light · Integral overheat and flame-out safety · Contractor-grade fuel cap

Factory tested for multiple fuels: Kerosene, JP8/Jet A fuel, No. 1 or No. 2 fuel oil and No. 1 or No. 2 diesel fuel

For use in any outdoor application.

Specifications subject to change without notice. Use in accordance with any and all state or local codes, regulations, and/or ordinances.

Please see heater “Owner’s Manual” included with each heater for a complete list of important safety information.

Important Notes:
· Not for use in residential living areas or inadequately ventilated areas.
· Proper ventilation required during operation.

The Mi-T-M Portable Heater Kerosene Radiant – MH-0125-1M1R Has the following Specifications:

Heat Output 95-125,000 BTU
Heat Type Radiant
AC Power 120 Volt/60Hz/3.15 to 5.0 Amps
Fuel Tank Capacity 11 gallons
Fuel Consumption Low-0.71 gal./hr. / High-0.9 gal./hr.
Max. Operating Hours Low-15.5 hrs. / High-12.2 hrs.
Heating Area 3,125 sq. ft.
Net Weight 80 lbs.
Shipping Weight 94 lbs.
Length 24.6 in.
Width 27.8 in.
Height 38.6 in.

View Product Information Brochure for Mi-T-M Portable Heater Kerosene Radiant – MH-0125-1M1R

List Price: $1,580.00
Our Price: $1,343.00
You save $237.00!
Availability:: available for order
Product Code: MH-0125-1M1R
Mi-T-M Portable Heater

September 23, 2011October 20, 2011

Annovi Reverberi Pressure Washer Pump RKA4G40HN

Annovi Reverberi Pressure Washer Pump RKA4G40HN4 GPM @ 4000 PSI.

Plunger Pumps are designed for a wide variety of high pressure washing applications. They are constructed of die-cast bodies and feature a forged brass head. Internal components include special thick solid ceramic plungers for long life and durability. Precision cast cooling fins are anodized for maximum heat dissipation. Oversized tapered roller bearings and the precision supports assure proper shaft alignment and maximum life. Valve cages of special designed Ultra-Form provide positive seating and extended life. One-piece connecting rods are either a special alloy aluminum or bronze oversized for strength and load disbursement. These pumps are designed for gearbox , belt drive, or coupling drive systems, electric motor 182-184 frame driven systems, or gasoline engine driven systems.

The Annovi Reverberi Pressure Washer Pump RKA4G40HN Features are:

Forged Brass: Strength and no porosity long life. higher hydrostatic pressures – safety, performance.
Inlet and Discharge Ports: Heavy bosses for added strength.
Offset Discharge Ports: High efficiency, smooth flow.
Bolts: Eight bolts, 8mm, grade 8.8.
Valve Caps: Stainless steel on pumps rated at 3200 PSI and higher, better hydrostatic loads. Machined brass on pumps <3200 PSI.
Ultra Form Cages: Durable, strength, and long life.
Poppets, Seat and Spring: 303 and 400 series stainless steel.
High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
Low Pressure Seals: “U” cup double lip Buna-N for a good positive seat.
Support and Guides: Machined brass, 1-piece construction to assure proper plunger alignment and to maximize packing and seal life.
Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
Bearings: Oversized tapered roller bearing for maximum life and load disbursement.
Bearing Support: Precision die-cast and machined to assure concentricity and alignment.
Crankcase: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
Rear Cover: Precision die-cast, O-ring sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen).
Plunger Rods: Stainless steel construction for strength (no plating to scrape off), back-up and Oring plunger sealing system.
Rod Pins: Precision ground and hardened steel, oversized for load disbursement.
Connecting Rods: One-piece special alloy aluminum or bronze for higher pressure, oversized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
Crankshaft: Forged, precision ground and hardened for extremely long life and durability.
Oil Seals and O-rings: Triple lip oil seals, long life and much less leak prone. All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
Oil Drains: Quantity of two (2). One in the rear cover and one in the bottom of the crankcase.
Oil Capacity: 15.5 oz.
Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
Valve Design: Each pump series has a valve design that optimizes its highest efficiency.

This Annovi Reverberi Pressure Washer Pump RKA4G40HN has the following specifications:

Max GPM……………… 4
Max LMP………………………… 15.1
Max PSI…………………. 4000
Max Bar…………………………. 275
Power EBHP…………… 11
Bore Dia. mm……………………. 18
Stroke mm………………. 12
Weight Lbs……………………….. 19
Max Temp………………. 140°
Oil Capacity……………………… 15oz
Inlet Thread …………… 1/2”F
Discharge Thread………………. 3/8”F

List Price: $854.02
Our Price: $532.74
You save $321.28!

Availability:: available for order
Product Code: RKA4G40HN
Annovi Reverberi Pressure Washer Pump
PSI: 4000
GPM: 4

Items NOT INCLUDED with your pump that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!

The PUMP GUARD will ‘dump’ any water above 145 degrees F. before it reaches your pump (saving you the trouble of rebuilding your pump)

PRESSURE REGULATOR / UNLOADER – if we list one to the right of the pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.

The INLET WATER FILTER will catch most small debris before it enters your pump

The EZ-START VALVE will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer.

The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your pump!

PUMP OIL, you can never have enough on hand! Many pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.

September 22, 2011October 20, 2011

Sorry for the re-blogging of old Posts.

At about 3:10 PM EST today 9/22/2011 our hosting companies web server where our database resides has an error and republished all of our blogs. We are sorry for the inconvenience and our hosting company is looking into this so it does not happen again. If you have any issues with any of our social media please feel free to e-mail me directly at craig@etscompany.com

Thank you ETS Company.

September 22, 2011October 20, 2011

COMET Pressure Washer Pump FW 5530 S – 6400.1400.00

COMET Pressure Washer Pump FW 5530 S – 6400.1400.00, 5.3 GPM @ 3000 PSI @ 1450 RPM, See product spec sheet for detailed specifications, repair kits and replacement parts. Click here.

The COMET Pressure Washer Pump FW 5530 S – 6400.1400.00 Features:

1/2 FPT Inlet, 3/8 FPT Discharge
Anodized, Die-Cast Aluminum Crankcase
Solid Ceramic Plungers
Stainless Steel Check Valves & Piston Guides
Oversized Bronze Connecting Rods
Buna-Textile V-Packings
Reversible Crankcase for Right or Left Hand Mounting
24mm Solid, Keyed Shaft

The COMET Pressure Washer Pump FW 5530 S – 6400.1400.00 has the following specifications:

Maximum Volume 5.5 gpm
Max. Discharge Pressure 3000 psi
Maximum Pump Speed 1450 rpm
Inlet Port Thread 1/2 FPT
Discharge Port Thread 3/8 FPT
Shaft Diameter 24mm Solid
Piston 20mm
Weight 19.4 lbs.

List Price: $1,085.00
Our Price: $542.34

You save $542.66!
Availability:: available for order
Product Code: 6400.1400.00
Comet Pressure Washer Pump \

Click links below for following resources:
Comet Pump Main Catalog
Comet Pump Breakdowns
Comet Pump Repair Manual

September 22, 2011October 20, 2011

Mi-T-M Portable Heater Propane Directional – MH-0085-0MDH

The MH-0085-0MDH Outer Casing/Design: Rugged design · Durable powder coated outer casing and side lifting handles · Lifting handles for easy loading and unloading · The unit is naturally balance to lift easily with handles · Two 10-inch solid rubber tires for mobility and easy placement

Components for the MH-0085-0MDH: Independent fan and burner controls for simple operation · Thermostat control with 20-foot cord allows for a consistent, comfortable environment and use in remote locations · 15-foot hose and regulator assembly · Air flow safety devices · Totally enclosed frame · Fully enclosed electronics · Electronic ignition · Operates as both a fresh air circulator or a heater at the touch of a switch · Super quiet, super efficient · Easy to set-up · Numerous duct options available · Direct spark ignition

The Mi-T-M Portable Heater Propane Directional – MH-0085-0MDH can be used in tent and party applications or construction sites.

Specifications subject to change without notice. Use in accordance with any and all state or local codes, regulations, and/or ordinances.

Please see heater “Owner’s Manual” included with each heater for a complete list of important safety information.

Important Notes:
· Not for use in residential living areas or inadequately ventilated areas.
· Proper ventilation required during operation.
· Extremely hot during operation. Keep children, animals and all combustible objects away from heater.

View Product Information Sheet for Mi-T-M Portable Heater Propane Directional – MH-0085-0MDH

MH-0085-0MDH Mi-T-M Portable Heater Propane Dirrectional

The Mi-T-M Portable Heater Propane Directional – MH-0085-0MDH has the following specifications:

Heat Output 85,000 BTU
Type Propane
Heated Air Output 750 CFM
Fuel Consumption 4.25 lbs./hr.
Inlet Gas Pressure 11-inch WC
Temperature Rise (above ambient) 140°F
Suggested Tank Size 100 lbs.
Electrical Requirements 115 Volts/60Hz/1Ø
Amps (Starting/Cont.) 8.2 / 2.3 Amps
Net Weight 122 lbs.
Shipping Weight 135 lbs.
Length 30 in.
Width 16 in.
Height 22 in.

List Price: $1,790.00
Our Price: $1,521.50
You save $268.50!
Availability:: available for order
Product Code: MH-0085-0MDH
Mi-T-M Portable Heater

September 21, 2011October 20, 2011

Mi-T-M Portable Heater Propane Forced Air – MH-0375-LM10

The MH-0375-LM10 Frame: Heavy-duty steel construction · Easy-lift handle for portability at home or on the job site

This MH-0375-LM10 Components: One touch ignition and heat control for easy operation · 10-foot hose and regulator · High performance fan · Automatic shut-off if power is interrupted or flame is extinguished · Enclosed gas controls · Electronic ignition · Propane inlet connector – connects heater to propane tank via a supply hose

Heat Output of the MH-0375-LM10 are: Adjustable thermostat

The MH-0375-LM10 is best used in workshops, garages, construction sites and farms with proper ventilation.

Specifications subject to change without notice. Use in accordance with any and all state or local codes, regulations, and/or ordinances.

Please see heater “Owner’s Manual” included with each heater for a complete list of important safety information.

Important Notes:
· Not for use in residential living areas or inadequately ventilated areas.
· Proper ventilation required during operation.
· Must be plugged into an approved standard electrical outlet for operation.

The Technical Specifications for the Mi-T-M Portable Heater Propane Forced Air MH-0375-LM10 are:

Heat Output 375,000 BTU
Hot-Air Flow 1,500 CFM
AC Power 120 Volt/60Hz/1.45 Amp
Motor Size 1/5 HP
Fuel Propane
Fuel Consumption 17.3 lbs./hr.
Required Cylinder Size (2) 100 lbs.
Max. Operating Hours 11.5 hours per required cylinder size
Heating Area 9,000 sq. ft.
Net Weight 41 lbs.
Shipping Weight 49 lbs.
Length 34 in.
Width 12.6 in.
Height 18.5 in.

List Price: $830.00
Our Price: $705.50
You save $124.50!
Availability:: available for order
Product Code: MH-0375-LM10

September 20, 2011October 20, 2011

Mi-T-M Portable Heater Propane Forced Air – MH-0150-NM10

Frame: Heavy-duty steel construction · Easy-lift handle for portability at home or on the job site · Adjustable height angle for heat where you need it

Components: One touch ignition and heat control for easy operation · High performance fan · Automatic shut-off if power is interrupted or flame is extinguished · Enclosed gas controls · Electronic ignition · Propane inlet connector – connects heater to propane tank via a supply hose

Heat Output: Adjustable thermostat

For use in workshops, garages, construction sites and farms with proper ventilation.

Specifications subject to change without notice. Use in accordance with any and all state or local codes, regulations, and/or ordinances.

Please see heater “Owner’s Manual” included with each heater for a complete list of important safety information.

The MH-0150-NM10 Mi-T-M Portable Heater Propane Forced Air has the following technical specifications:

Heat Output 150,000 BTU
Hot-Air Flow 435 CFM
AC Power 120 Volt/60Hz/Less than 1.0 Amp
Motor Size 1/9 HP
Fuel Natural Gas
Fuel Consumption 150 cu. ft./hr.
Heating Area 3,800 sq. ft.
Net Weight 24 lbs.
Shipping Weight 35 lbs.
Length 25.1 in.
Width 9 in.
Height 15.5 in.

List Price: $550.00
Our Price: $476.50
You save $73.50!
Availability:: available for order
Product Code: MH-0150-NM10

September 19, 2011October 20, 2011

COMET Pressure Washer Pump FW 4030 S – 6400.1106.00

COMET Pressure Washer Pump FW 4030 S – 6400.1106.00, 4.0 GPM @ 3000 PSI @ 1450 RPM, See product spec sheet for detailed specifications, repair kits and replacement parts.

The COMET Pressure Washer Pump FW 4030 S – 6400.1106.00 Features:

1/2 FPT Inlet, 3/8 FPT Discharge
Anodized, Die-Cast Aluminum Crankcase
Solid Ceramic Plungers
Stainless Steel Check Valves & Piston Guides
Oversized Bronze Connecting Rods
Buna-Textile V-Packings
Reversible Crankcase for Right or Left Hand Mounting
24mm Solid, Keyed Shaft

This COMET Pressure Washer Pump FW 4030 S – 6400.1106.00 has the following technical specifications:

Maximum Volume 4.0 gpm
Max. Discharge Pressure 3000 psi
Maximum Pump Speed 1450 rpm
Inlet Port Thread 1/2 FPT
Discharge Port Thread 3/8 FPT
Shaft Diameter 24mm Solid
Piston 18mm
Weight 19.4 lbs.

List Price: $1,025.00
Our Price: $512.79

You save $512.21!
Availability:: Usually Ships in 24 Hours
Product Code: 6400.1106.00

Click links below for following resources:
Comet Pump Main Catalog
Comet Pump Breakdowns
Comet Pump Repair Manual

September 19, 2011October 20, 2011

CAT Pressure Washer Pump 530

CAT Pressure Washer Pump 530 7PFR Ceramic Plunger, 5.0/2500, 1100 RPM, D-End, BBCP/S-Valves.

Need parts for this CAT Pressure Washer Pump 530?

Click here for the datasheet for CAT Pressure Washer Pump 530.

Click here for servicing instructions for this CAT Pressure Washer Pump 530.

The CAT Pressure Washer Pump 530 Features:

Triplex plunger provides smoother liquid flow.
Hi-Pressure Seals or V-Packings are completely lubricated and cooled by the liquid being pumped.
Inlet and discharge valve assemblies interchange for easier maintenance.
Lubricated Lo-Pressure Seals provide double protection against external leakage.
Oil bath crankcase assures optimum lubrication.
Close tolerance concentricity of the ceramic plunger maximizes seal life.
Precision design 304 stainless steel valves and seats are hardened and polished for ultimate seating and extended valve life.
Forged brass manifold is strong and corrosion resistant.
Special concentric, high-density, polished, solid ceramic plungers provide a true wear surface and extended seal life.
Specially formulated, CAT PUMP exclusive, Hi-Pressure Seals or
V-Packings offer unmatched performance and seal life.
Die cast aluminum crankcase provides high strength, minimum weight and precision tolerance control.
Chrome-moly crankshaft gives unmatched strength and surface hardness.
Oversized crankshaft bearings with greater capacity mean longer bearing life.
Wet end is easily serviced without entering crankcase, requiring less time and effort.
Valve assemblies are accessible without disturbing piping, for quick service.
Preset packings mean no packing gland adjustment is necessary, reducing maintenance costs.

This CAT Pressure Washer Pump 530 has the following technical specifications:

Flow…………………………………………………..5.0 GPM (19 L/M)
Pressure Range………………………..100 to 2500 PSI (7 to 175 BAR)
RPM ……………………………………………….1100 RPM (1100 RPM)
Bore……………………………………………………..0.708″ (18 mm)
Stroke…………………………………………………..0.945″ (24 mm)
Inlet Pressure Range………………Flooded to 60 PSI (Flooded to 4 BAR)
Crankcase Capacity ………………………………..25 oz. (0.75 L)
Maximum Liquid Temperature …………………..160°F (71°C)
For temperatures above 130°F call CAT PUMPS for inlet conditions and elastomer recommendations.
Inlet Ports (2) ……………………………………1/2″ NPTF (1/2″ NPTF)
Discharge Ports (2)……………………………3/8″ NPTF (3/8″ NPTF)
Shaft Diameter ……………………………………….0.945″ (24 mm)
Weight………………………………………………..25.5 lbs. (11.5 kg)
Dimensions…………………………..13.6 x 9.61 x 6.41″ (346 x 244 x 163 mm)

List Price: $1,853.02
Our Price: $1,425.90
You save $427.12!
Availability:: Usually Ships in 24 Hours
Product Code: BAPL-2616

September 16, 2011October 20, 2011

Annovi Reverberi Pressure Washer Pump XMV2.5G26D-F25

Annovi Reverberi Pressure Washer Pump XMV2.5G26D-F25 2.5 GPM @ 2600 PSI
Plunger Pumps are designed for a wide variety of high pressure washing applications. They are constructed with die-cast bodies and feature a brass head. Internal components include special thick solid ceramic plungers for long life and durability. Precision cast cooling fins are anodized for maximum heat dissipation. Oversized needle bearings on the drive side, and ball on the non-drive side together with the precision supports assure positive alignment and centering in relation to the crankcase. Valve cages of special designed Ultra-Form provide positive seating and extended life. Ball bearings on both sides of solid shaft drive pumps. One-piece connecting rods are special alloy aluminum, oversized for strength and load disbursement. These pumps are designed for gearbox , belt drive, or coupling drive systems driven by eletric motor or gasoline driven systems, gasoline engine driven systems.

Annovi Reverberi Pressure Washer Pump XMV2.5G26D-F25 Features:

Forged Brass: Strength and no porosity equals long life. Higher hydrostatic pressures, safety and performance.
Inlet and Discharge Ports: Heavy bosses for added strength.
Offset Discharge Ports: High efficiency, smooth flow.
Bolts: Eight bolts, 6mm, grade 12.9.
Ultra Form Cages: Durability, strength and long life.
Poppets, Seat and Spring: 303 and 400 series stainless steel.
Valve Caps: Machined brass – greater strength.
Packing and Plungers:
High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
Low Pressure Seals: “U” cup double lip Buna-N, good positive seal.
Support Guides: Machined brass, two-piece construction to assure proper plunger alignment and to maximize packing and seal life.
Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
Bearings: Oversized for maximum life and load disbursement, needle bearing on the drive side and ball on the non-drive side. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
Crankcase: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
Rear Cover: precision die-cast, O-ring sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen).
Plunger Rods: Stainless steel construction for strength (no plating to scrape off). O-ring plunger sealing system.
Rod Pins: Precision ground and hardened steel, oversized for load disbursement.
Connecting Rods: One-piece special alloy aluminum based, oversized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
Crankshaft: Forged, precision ground and hardened for extremely long life and durability.
Oil Seals and O-rings: All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
Oil Capacity: 14.5 oz., refer to parts breakdown.
Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
Hot Water: High temperature kits are available to 180º F. Refer to breakdown
Wet End Repair: Very simple no special tools are required.
Mounting Bolt Pattern: Same on the top and bottom of the crankcase for simple drive side change.
Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.

Annovi Reverberi Pressure Washer Pump XMV2.5G26D-F25 has the following specifications:

Max GPM………………2.5
Max LMP…………………………9.5
Max PSI………………….2600
Max Bar………………………….179
Power EBHP……………5
Bore Dia. mm…………………….15
Stroke mm……………….6.2
Weight Lbs………………………..15
Max Temp……………….140°
Oil Capacity………………………14.6oz
Inlet Thread ……………1/2”F
Discharge Thread……………….3/8”F

Items NOT INCLUDED with your Annovi Reverberi Pressure Washer Pump XMV2.5G26D-F25that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!The PUMP GUARD will ‘dump’ any water above 145 degrees F. before it reaches your pump (saving you the trouble of rebuilding your pump)PRESSURE REGULATOR / UNLOADER – if we list one to the right of the pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.

The INLET WATER FILTER will catch most small debris before it enters your pump

List Price: $588.80
Our Price: $369.47

You save $219.33!

Availability:: Usually Ships in 24 Hours
Product Code: XMV2.5G26D-F25