The KF36A pump has been designed to pump fresh and filtered (360 micron max.) water at room temperature. Special versions are available for pumping water up to 185F and for reverse osmosis units.
The water temperature is critical for the pump life: the higher the water temperature, the more likely it is to create cavitation, resulting in premature seal and valve failures. For such conditions, use HT series pumps.
List Price: $8,400.00 Our Price: $6,463.80 Click the link to order this KF36A Pressure Washer Pump You save $1,936.20! Availability:: available for order Product Code: KF36A Price subject to change. Price valid on this KF36A Pressure Washer Pump 6/7/2012
Spotlight on the AR Annovi Reverberi Pressure Washer Pump XT9.14N
AR Annovi Reverberi Pressure Washer Pump XT9.14N
The AR Annovi Reverberi Pressure Washer Pump XT9.14N has the following Technical Specifications:
Max GPM……………… 2.37
Max LMP………………………… 9.0
Max PSI…………………. 2000
Max Bar…………………………. 140
Power EBHP…………… 3.3
Bore Dia. mm……………………. 18
Stroke mm………………. 8.4
Weight Lbs……………………….. 11
Max Temp………………. 140°
Oil Capacity……………………… 10oz
Inlet Thread …………… 1/2”F
Discharge Thread………………. 3/8”F
XT9.14N AR (Annovi Reverberi) Pump 2.37 GPM @ 2000 PSI.
XT9.14N Plunger Pumps are designed for a wide variety of moderate pressure washing applications. They are constructed with die-cast bodies and feature a brass head. Internal components include special thick solid ceramic plungers for long life and durability. Precision cast cooling fins are anodized for maximum heat dissipation. Oversized needle bearing on the drive sides and ball bearings on the non-drive side assure proper shaft alignment and maximum life. Valve cages of special designed Ultra-Form impervious to water absorption provide positive seating and extended life. One-piece connecting rods are either a special alloy aluminum or bronze at higher pressures, oversized for strength and load disbursement.
AR Annovi Reverberi Pressure Washer Pump XT9.14N
The AR Annovi Reverberi Pressure Washer Pump XT9.14N Features:
Manifold:
– Forged Brass: Strength and no porosity equals long life. Higher hydrostatic pressures, safety, performance.
– Inlet and Discharge Ports: Heavy bosses for added strength.
– Offset Discharge Ports: High efficiency, smooth flow.
– Bolts: Six Bolts, 6mm, grade 12.9.
Valves:
– Ultra Form Cages: Durability, strength and long life.
– Poppets, Seat and Spring: 303 and 400 series stainless steel.
– Valve Caps: Machined brass – greater strength.
Packing and Plungers:
– High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
– Low Pressure Seals: “U” cup double lip Buna-N. Good positive seal.
– Support Guides: Machined brass one-piece construction to assure proper plunger alignment and to maximize packing and seal life.
– Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
Bearings: Oversized for maximum life and load disbursement, two ball bearings on the solid shaft series and a needle bearing on the drive side and ball on the non-drive side for the hollow shaft series. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
Crankcase: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
Rear Cover: Precision die-cast, precision punched gasket sealed and bayonet style sightglass for positive sealing and locking (no threads to loosen).
Plunger Rods: Stainless steel construction for strength (no plating to scrape off). O-ring plunger sealing system.
Rod Pins: Precision ground and hardened steel,
oversized for load disbursement.
Connection Rods: One piece special alloy aluminum based and bronze, oversized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
Crankshaft: Forged one-piece, precision ground and hardened for extremely long life and durability.
Oil Seals and O-rings: All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
Oil Capacity: Flat cover 8 oz. and extended cover 10 oz.
Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
Hot Water: High temperature kits are available to 180º F. Refer to breakdown.
Wet End Repair: Very simple no special tools are required.
Mounting Bolt Pattern: Same on the top and bottom of the crankcase for simple drive side change.
Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.
List Price: $571.65 Our Price: $358.91 Click the link to order this Pressure washer pump XT9.14N You save $212.74! Availability:: available for order Product Code: XT9.14N
Price subject to change. Price valid on thie XT9.14N pressure washer pump 6/6/2012
Spotlight on the AR Annovi Reverberi Pressure Washer Pump XWL-SS42.15N.
AR Annovi Reverberi Pressure Washer Pump XWL-SS42.15N
XWL-SS42.15N AR (Annovi Reverberi) Pump 11 GPM @ 2200 PSI.
In high frequency and long time operation, high accurate manufacturing technique is the only answer to the durable reputation Annovi Reverberi XWL-SS42.15N pumps. The S.S. Series uses include various applications such as reverse osmosis water desalination, seal gland flushing and waste water odor control. S.S. Series XWL-SS42.15N feature a SAE 316 stainless steel manifold this is totally corrosion-resistance. Special pumps features include our highly concentric bearing positioning on both sides of the crankcase, anticorrosion coated aluminum die cast crankcase, continuously lubricated Viton seals, triple lip loaded oils seals and our ultra thick ceramic plungers that will not crack.
The Annovi Reverberi Pressure Washer Pump XWL-SS42.15N has the following specifications:
Max GPM………………11
Max LMP…………………………42
Max PSI………………….2200
Max Bar………………………….150
Power EBHP……………15
Bore Dia. mm…………………….28
Stroke mm……………….17.2
Weight Lbs………………………..36
Max Temp……………….140°
Oil Capacity………………………32oz
Inlet Thread ……………3/4”F
Discharge Thread……………….3/8”F
XWL-SS42.15N-3 break down
The Pressure Washer Pump XWL-SS42.15N Features:
Manifold:
– 316L – Stainless Steel Block Style: Strength and no porposity = long life.
– Inlet and Discharge Ports: 1/2” inlet and 3/8” discharge.
– Offset Discharge Ports: High efficiency, smooth flow
– Bolts: 8 Bolts, 10mm, stainless steel.
Valves:
– Ultra Form Cages: Durable, strength, and long life.
– Poppets, Seat and Spring: 316 series stainless steel.
– Valve Caps: Machined 316L series stainless steel.
Packing and Plungers:
– High Pressure Packing: “Special profile” style (W-1) Viton (cotton duct weave base) strong and tightens under load.
– Low Pressure Seals: “W-2” style Viton, good positive seal.
– Support and Guides: Machined stainless steel, 1-piece construction with intermediate and guide rings to assure proper plunger alignment, maximize packing and seal life.
– Plungers: Special aluminum oxide blend, solid ceramic long life, strong and durable. Ultra thick with a locating step and SST retaining bolts.
Bearings: Premium oversized taper for maximum life and load dispersement.
Bearings Supports: Precision die-cast and machined to assure concentricity and alignment.
Crankcase: Precision die-cast, large cooling fins and covered with a special anti-corrosion finish.
Rear Cover: Precision die-cast, O-Ring sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen). This is an “AR” orginal. Oil drain plug.
Plunger Rods: Stainless steel construction for strength, back-up and O-ring plunger sealing system.
Special acorn style retaining nuts and SST slingers.
Rod Pins: Precision ground and hardened steel, oversized for load dispersement.
Connection Rods: 2-piece special alloy bronze for higher pressures, oversized for maximum strength, load dispersement, and life. Heavy pin area construction.
Crankshaft: Forged, precision ground and hardened for extremely long life and durability. Available in 24mm solid shaft for gearbox drives. Shaft key set screws are standard on high-speed version for long shaft life.
Oil Seals and O-Rings: Triple lip oil seals, long life and much less leak prone. All are constructed of Buna-N rubber. The O-Rings have stainless steel garder springs for assure constant tension on the sealing surface.
Oil Drains: Quantity of 2. One in the rear cover and one in the bottom of the crankcase.
Oil Capacity: 32 oz.
Oil Sight Glasses: Rear cover and non-drive side bearing housing.
Dyno Proven: All pumps are dyno tested to assure the theroretical design meets the actual design.
Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
Hot Water: High temperature kits are available to 180°F.
Wet End Repair: Very simple no special tools are required.
Mounting Flanges: Multiple flanges are available.
Buna-N: Elastomers available.
Is this not the right pressure washer pump? Click the link to see all our XW Stainless Steel Series pressure washer pumps.
List Price: $5,356.49 Our Price: $3,304.46 Click the link to order this XWL-SS42.15N Pressure Washer Pump You save $2,052.03! Availability:: available for order Product Code: XWL-SS42.15N Price subject to change. Price valid on this XWL-SS42.15N – 6/4/2012
The CAT Pump 323 has Superior Design
•Triplex Uniflow design provides continuous forward liquid flow for smooth operation.
• Wetted cups and floating pistons are lubricated and cooled by pumped liquid for long cup life.
•Mechanically actuated inlet valves give strong lift and easy prime.
•Precision design 304 stainless steel valves and seats are hardened and polished for ultimate seating and extended valve life.
•Oil bath crankcase assures optimum lubrication.
•100% wetted seal design allows pumped liquid to cool and lubricate for longer life.
This CAT Pump 323 uses Quality Materials
•Cylinder and sleeve wear surfaces are hard chrome plated 304 stainless steel for maximum durability and abrasion resistance.
•Chrome plated, brass manifolds for strength and corrosion resistance.
•Special high strength TNM connecting rods offer superior bearing quality strength.
•Chrome-moly crankshaft gives unmatched strength and surface hardness.
•Over sized crankshaft bearings with greater loading capacity mean longer bearing life.
The CAT Pump 323 has Easy Maintenance
•Stepped stainless steel piston rod with chrome-plated, stainless steel sleeve allows easy replacement from front of pump.
•All wet-end wear parts are easily serviced without entering crankcase, requiring less time and effort.
•Wear parts are available in convenient kits.
Crankcase Capacity …………………………………………..21 oz. (0.6 L)
Pulley Mounting ………………………………………….Either side (Either side)
Shaft Diameter………………………………………………….0.787″ (20 mm)
Is this not the right CAT Piston Pump? Click the link to see more CAT Piston Pumps from Shopetsonline.
Our Price: $1,515.00 Click the link to order the CAT Pump 323 Call 1-877-824-7763 for a Better Price{WE CAN’T LIST OUR BEST PRICE ONLINE! CALL US TODAY!} Availability:: Available for Order Product Code: 323 Price subject to change. Price valid on the CAT Pump 323 – 5 Frame Piston Pump 6/01/2012
• The CAT Pump 333 has Triplex Uniflow design provides continuous forward liquid flow for smooth operation.
• Wetted cups and floating pistons are lubricated and cooled by pumped liquid for long cup life.
• Mechanically actuated inlet valves give strong lift and easy prime on this CAT Pump 333.
• 304 stainless steel discharge valves for wear resistance.
• Oil bath crankcase assures optimum lubrication.
• 100% wetted seal
Dimensions……………………………………12.56 x 8.8 x 5.33″ (319 x 223 x 135.5mm)
Is the CAT Pump 333 not the right CAT Piston Pressure Washer Pump? Click the link to see all our CAT Pressure Washer Piston Pumps from Shopetsonline.com.
Our Price: $1,465.00 Click to order this CAT Pump 333. Call 1-877-824-7763 for a Better PriceWe can’t list online!!! Availability:: Available for Order Product Code: 333 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE CAT PUMP 333 – 5/23/2012
•The CAT Pump 290 has a Triplex UNIFLOW design provides a smooth, low-pulsation flow with strong suction capabilities.
•Hard chrome-plated 304S cylinders and sleeves provide long life with mild liquids within a range of 5-9 PH.
•Optional 316 Stainless Steel manifolds on the CAT Pump 290 are for added strength and corrosion resistance.
•Optional FPM and PTFE elastomers for liquid compatibility.
Discharge Port (1)…………………………..1/2” NPTF (1/2” NPTF)
Pulley Mounting……………………………..Either side (Either side)
Shaft Diameters…………………………………..0.650” (16.5 mm)
Dimensions (290)……………..10.83 x 8.79 x 5.30” (275 x 223x 134.5 mm)
Is this CAT Pump 290 not the right Piston Pressure Washer Pump for your machine? Click the link to see all our CAT Piston Pressure Washer Pumps.
Our Price: $995.00 Click the link to order the CAT Pump 290. Call 1-877-824-7763 for a Better Price Availability:: Available for Order Product Code: 290 PRICE SUBJECT TO CHANGE. PRICE VALID ON THIS CAT PUMP 290 – 3 FRAME PISTON PUMP 5/21/2012
List Price: $887.35 Our Price: $553.25 Click the link to order the SXMV4G40-PKG Pressure Washer Pump. You save $334.10! Availability:: available for order Product Code: SXMV4G40-PKG Price subject to change. Price valid on the sxmv4g40-PKG – 5/18/2012
List Price: $1,068.49 Our Price: $664.77 Click the link to order this RKV4G37-PKG You save $403.72! Availability:: available for order Product Code: RKV4G37-PKG Price subject to change. Price valid on this RKV4G37-PKG on 5/16/2012
List Price: $1,081.58 Our Price: $672.82 Click the link to order the RKV4G40-PKG. You save $408.76! Availability:: available for order Product Code: RKV4G40-PKG Price subject to change. Price valid on the AR Annovi Reverberi Pressure Washer Pump RKV4G40-PKG – 5/14/2012
Spotlight on the AR Annovi Reverberi Pressure Washer Pump RMV2.5G24D-(Alm).
AR Annovi Reverberi Pressure Washer Pump RMV2.5G24D-(Alm)
This RMV2.5G24D-(Alm) plunger pump will pump up to 2.5 GPM at 2400 PSI. It spins at 3400 RPM in a direct drive system coupled with a gasoline engine. The matching flange provides convenient connection to most 3/4” shaft 1.1 – 5.5 HP engines. The hollow shafted RMV2.5G24D-(Alm) pump includes a built-in pressure control valve, and chemical injection system.
The AR Annovi Reverberi Pressure Washer Pump RMV2.5G24D-(Alm) Features:
Manifold: High strength forged brass for long term use.
Bolts: Three 6mm cadmium plated steel.
Plungers: Hardened stainless steel.
Valves: Stainless steel poppet, seat and cage, stainless steel spring.
Seals: Buna-N dual seals.
Bearings: Premium oversized ball and needle bearings.
Crankshaft: Precision die-cast, with cooling fins for maximum heat dissipation. The housing retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer.
The AR Annovi Reverberi Pressure Washer Pump RMV2.5G24D-(Alm) has the following specifications:
List Price: $189.40 Our Price: $123.59 Click the link to order this RMV2.5G24D-(Alm) Pressure Washer Pump. You save $65.81!
Availability:: available for order Product Code: RMV2.5G24D-(ALM) Price subject to change. Price valid on this RMV2.5G24D-(Alm) – 5/10/2012
