Spotlight on the AR Annovi Reverberi Pressure Washer Pump RMV2G25D.
RMV2G25D AR (Annovi Reverberi) Pump 2 GPM @ 2500 PSI
This RMV2G25D plunger pump will pump up to 2 GPM at 2500 PSI. It spins at 3400 RPM in a direct drive system coupled with a gasoline engine. The matching flange provides convenient connection to most 3/4” shaft 1.1 – 5.5 HP engines. The hollow shafted RMV2G25D pump includes a built-in pressure control valve, and chemical injection system.
AR Annovi Reverberi Pressure Washer Pump RMV2G25D
The AR Annovi Reverberi Pressure Washer Pump RMV2G25D Features:
Manifold: High strength forged brass for long term use.
Bolts: Three 6mm cadmium plated steel.
Plungers: Hardened stainless steel.
Valves: Stainless steel poppet, seat and cage, stainless steel spring.
Seals: Buna-N dual seals.
Bearings: Premium oversized ball and needle bearings.
Crankshaft: Precision die-cast, with cooling fins for maximum heat dissipation. The housing retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer.
AR Annovi Reverberi Pressure Washer Pump RMV2G25D
The AR Annovi Reverberi Pressure Washer Pump RMV2G25D has the following Technical Specifications:
Max GPM……………… 2
Max LMP………………………… 7.6
Max PSI…………………. 2500
Max Bar…………………………. 172
Power EBHP…………… 3.4
Bore Dia. mm……………………. 12
Stroke mm………………. 8.3
Weight Lbs……………………….. 7.5
Max Temp………………. 140°
Oil Capacity……………………… 2.2oz
Inlet Thread …………… 3/4”
GH Discharge Thread………………. 22mm
Annovi Reverberi Pressure Washer Pump
List Price: $307.66 Our Price: $196.39 CLICK RMV2G25D TO ORDER You save $111.27! Availability:: available for order Product Code: RMV2G25D PRICE SUBJECT TO CHANGE. PRICE VALID ON THE AR Annovi Reverberi Pressure Washer Pump RMV2G25D – 1/19/2012
Oil Capacity = 4.5 oz, Maximum Fluid Temperature = 140° F, Inlet Thread = 1/2”M, Discharge Thread = 3/8”M
SPECIAL NOTE: Use only AR64545 (click link to view/purchase oit) for the XJ/SJ/BK Series pumps only: Do NOT change oil. Use oil only to add if low. This oil is a specially formulated synthetic with special additives for the demands of the XJ, SJ and BK pump series. No other oil is factory approved for these pumps, and could result in pump failure.
This AR XJW24G24D-F27 pump is designed for medium duty loads. It spins at 3400 RPM in a direct drive system coupled with a gasoline engine, the matching flange provides convenient connections to most 3/4” shaft 3.5 – 6.5 HP engines. Optional vertical and horizontal setups. Precision die-cast crankcase with large cooling fins for maximum heat dissipation. Seals and V-Packings designed to continuously lubricate for extended life. The XJW24G24D-F27 has a Built-in unloader to optimize performance while reducing setup time. Integral trap pressure with fixed or adjustable chemical injector.
AR Annovi Reverberi Pressure Washer Pump XJW24G24D-F27
The AR Annovi Reverberi Pressure Washer Pump XJW24G24D-F27 has the following specifications:
Max GPM………………2.4
Max LMP…………………………9
Max PSI………………….2400
Max Bar………………………….166
Power EBHP……………3.9
Bore Dia. mm…………………….15
Stroke mm……………….5.8
Weight Lbs………………………..11
Max Temp……………….140°
Oil Capacity………………………4.5oz
Inlet Thread ……………1/2”M
Discharge Thread……………….3/8”M
XJW24G24D-F27 Pump Exploded View
The AR Annovi Reverberi Pressure Washer Pump XJW24G24D-F27 Features:
Manifold:
– Forged Brass: Strength and no porosity – long life. Higher hydrostatic pressures – safety.
– Unloader: Built in to optimize performance while reducing setup time. Integral trap pressure, fixed or adjustable chemical injector.
– Bolts: Three bolts, 10mm, grade 8.8.
Valves:
– Ultra Form Cages: Durable, strong, and long life. Unique inlet valve configuration: the valve cage incorporates the high pressure packing head ring.
– Poppets, Seat and Spring: 303 and 400 series stainless steel.
– Valve Caps: Machined brass for greater strength.
Packing and Plungers:
– High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load. Continuously lubricating for extended life, self lubricating packing/Plunger guide support ring.
– Low-Pressure Seals: “U” cup double lip Buna-N for a good positive seat.
– Support and Guides: Machined brass, 1-piece construction to assure proper plunger alignment, maximize packing and seal life.
– Plungers: Coated ceramic stainless steel, strong and durable. The pump includes a plunger shoe to distribute the additional plunger load.
Bearings: Angular contact ball bearing stabilizes the crankshaft and one thrust needle bearing absorbs the plunger load and assures long radial plate life. All of the thrust plates are made of heat treated hardened steel for extended life.
Crankcase: Precision die-cast, large cooling fins and anodized for maximum heat dissipation. Sight glass, fill and drain plugs.
Rear Cover: Precision die-cast, O-ring sealed. The housing retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer.
Crankshaft/Wobble Plate: Precision die-cast to assure proper stroke, duration and alignment.
Oil Seals and O-rings: All are constructed of Buna-N rubber. The oil seals have stainless steel garder springs to assure constant tension on the sealing surface.
Oil Capacity: 4.5 oz.
Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
Wet End Repair: Very simple no special tools required.
Mounting Flanges: Gasoline SAE J609a flange. Refer to breakdown.
Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.
List Price: $484.10 Our Price: $305.01 You save $179.09! Availability:: available for order Product Code: XJW24G24D-F27 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE XJW24G24D-F27 – 1/18/2012
The repair Manual for the Giant Pressure Washer Pump P313 can be found by clicking here.
GIANT Pressure Washer PUMP P313
INSTALLATION INSTRUCTIONS FOR THE GIANT Pressure Washer PUMP P313
Installation of the Giant Industries, Inc., pump is not a complicated procedure, but there are some basic steps common to all pumps. The following information is to be considered as a general outline for installation. If you have unique requirements, please contact Giant Industries, Inc. or your local distributor for assistance.
1. The P313 pump should be installed flat on a base to a maximum of a 15 degree angle of inclination to ensure optimum lubrication.
2. The inlet to the P313 pump should be sized for the flow rate of the pump with no unnecessary restrictions that can cause cavitation. Teflon tape should be used to seal all joints. If pumps are to be operated at temperatures in excess of 1600 F, it is important to insure a positive head to the pump to prevent cavitation.
3. The discharge plumbing from the pump should be properly sized to the flow rate to prevent line pressure loss to the work area. It is essential to provide a safety bypass valve between the pump and the work area to protect the pump from pressure spikes in the event of a blockage or the use of a shut-off gun.
4. Use of a dampener is necessary to minimize pulsation at drive elements, plumbing, connections, and other system areas. The use of a dampener with Giant Industries, Inc. pumps is optional, although recommended by Giant Industries, Inc. to further reduce system pulsation. Dampeners can also reduce the severity of pressure spikes that occur in systems using a shut-off gun. A dampener must be positioned downstream from the unloader.
5. When viewed from the side of the P313 pump, crankshaft rotation is clockwise on pumps with left handed shafts and counterclockwise on pumps with right handed shafts. Reverse rotation may be safely achieved by following a few guidelines available upon request from Giant Industries, Inc. Required horsepower for system operation can be obtained from the charts on pages 3-7 and 10.
6. Before beginning operation of your pumping system, remember: Check that the crankcase and seal areas have been properly lubricated per recommended schedules. Do not run the P313 pump dry for extended periods of time. Cavitation will result in severe damage. Always remember to check that all plumbing valves are open and that pumped media can flow freely to the inlet of the P313 pump.
List Price: $1,008.31 Our Price: $924.01 You save $84.30! Availability:: available for order Product Code: LAN-8.702-356.0 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE GIANT PRESSURE WASHER PUMP P313 – 1/09/2012
Spotlight on GENERAL PRESSURE WASHER PUMP,TS1021L SERIES 47
The TS1021L is the preferred pump frame in the pressure cleaning industry
• Forged brass manifold with an exclusive lifetime warranty
• Large-capacity, die-cast, anodized aluminum oil-bath crankcase
• Over-sized connecting rods for maximum life
• Heavy-duty tapered roller bearing.
• Solid ceramic plungers with continuously lubricated packings
• Unitized stainless steel inlet and discharge valves
• Available in left-handed “L” version
GENERAL PRESSURE WASHER PUMP,TS1021L SERIES 47
The GENERAL PRESSURE WASHER PUMP,TS1021L SERIES 47 Features:
General 47 Series Triplex Plunger Pump (left Handed)
Solid Shaft for Belt or Gear Drive
Max. Volume: 5.6 GPM
Max. Discharge Pressure: 1,700 PSI
Max. Pump Speed: 1450 RPM
Shaft Diameter: 24mm Solid
Max. Horsepower Requirements: 9.0 GHP
Max. Fluid Temp.: 165 degrees F.
Inlet Ports (2): 1/2″ BSP
Discharge Ports (2): 3/8″ BSP
Drive Side: Left
Forged brass head & valve covers
Solid ceramic plungers
Weight: 32.0 lb.
TS1021L Pressure Washer Pump
List Price: $1,206.90 Our Price: $631.52 You save $575.38! Availability:: available for order Product Code: TS1021L PRICE SUBJECT TO CHANGE. PRICE VALID ON THE GENERAL PRESSURE WASHER PUMP TS1021L – 1/5/2012
Dimensions……………………………..11.73 x 10.0 x 5.24” (298 x 254 x 133 mm)
Weight of the 310 CAT PUMP: 19.8 lbs.
Flow …………………………………………………………….4.0 gpm (15 l/m)
Pressure Range………………………………100 to 2200 psi (7 to 155 bar)
RPM ……………………………………………………………950 rpm (950 rpm)
Inlet Pressure Range……………………………–5 to 60 psi (–0.35 to 4 bar)
Stroke ……………………………………………………………..0.709” (18 mm)
310 CAT PUMP exploded VIEW
Lubrication: fill crankcase with CAT Pump hydraulic oil per pump specifications. DO NOT RUN PUMP WITHOUT OIL IN CRANKCASE. Change initial oil after a 50 hour break-in period, and every three months or 500 hour intervals thereafter.
List Price: $1,159.06 Our Price: $891.90 Click to order the 310 CAT Pump Availability:: available for order Product Code: BAPL-2798 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE 310 CAT PUMP 1/4/2012
Pulley Mounting…………………………………………….Either Side (Either Side)
Shaft Diameter…………………………………………………… 1.378” (35 mm)
CAT Pump 3535Weight……………………………………………………………..139 lbs. (63 kg)
Dimensions (3535, 3535C)……………….23.87 x 18.11 x 9.72” (606.5 x 460 x 247 mm)
Our Price: $6,712.00 Call 1-877-824-7763 {for a better price} Availability:: Available for Order Product Code: 3535 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE CAT PUMP 3535 – 12/28/2011
The General Pressure Washer Pump TS1021 ,T SERIES 47 Features:
The preferred pump frame in the cleaning industry
The TS1021 has a Forged brass manifold with an exclusive lifetime warranty
Large capacity, die cast, anodized aluminum oil bath crankcase
Over sized connecting rods for maximum life
Heavy duty tapered roller bearing
The TS1021 Pump has solid ceramic plungers with continuously lubricating packings
Unitized stainless steel inlet and discharge valves
The TS1021 is Available in left handed “L” version
General Pressure Washer Pump TS1021
The General Pressure Washer Pump TS1021,T SERIES 47 has the following specifications:
Maximum Volume: 4.5/5.6 GPM
Maximum Discharge Pressure: 3000/1700 PSI
Maximum Inlet Pressure: 125 PSI
Maximum Pump Speed: 1125/1450 RPM
Minimum Horsepower Requirements: 6.5 bhp (9.8 hp for gas engines)
Bore: .787″ (20mm)’
Stroke: .630″ (16mm)
Crankcase Capacity: 40.6 oz. non-detergent SAE 30W oil.
Maximum Fluid Temperature: 165 F.
Inlet Port Thread: 1/2″ FPT
Discharge Port Thread: 3/8″ FPT
Shaft Diameter: .945″ (24mm)
Dimensions of the TS1021: 12.6″ x 8.8″ x6.9″
Weight: 32.0 lb.
Lubrication: Fill the crankcase to the dot on the oil gauge window per specifications with non-detergent SAE 30W oil. Change the oil in the TS1021 after 40 hour break-in period, then every three (3) months or 500 hour intervals thereafter
The following statement is intended to assist our customers in understanding the terms of General Pump’s warranty, the circumstances under which they will honor claims, and the procedure for making such claims.
General Pump/US warrants each pump to be free of defects in material or workmanship for a period of five (5) years from the date of shipment. In addition, General Pump/US warrants all forged brass pump manifolds to be free of defects in material and workmanship and from damage resulting from freezing for the life of the pump. Liability on this warranty is on all non-wear parts and limited to the repair or replacement of any pump returned to General Pump/US which upon inspection is judged to be defective due to workmanship or material failure.
In the course of marketing or servicing the customer or potential customer’s needs, General Pump/US will use its best judgment in its recommendations. However, the ultimate responsibility for product application decisions shall rest with the customer. the sole and only warranty made by General Pump/US is the limited warranty described above. General Pump/US makes no other warranty or warranties of any kind, express or implied, including any implied warranty or merchantability or of any fitness for a particular use or purpose.General Pump/US disclaims and denies any liability for any direct, indirect, special, incidental or consequential damages which may be suffered as a result of sale, delivery, servicing, use, loss of any product, downtime, labor, freight or other charges not expressly included herein. the only liability and the total liability of General Pump/US under this limited warranty or in any claim regarding or involving General Pump/US is expressly limited to the replacement of or purchase price of the product.
The following items are NOT warranted, due to matters beyond General Pump/US control. Normal wear and tear to parts that are considered standard wear parts. Defects caused by the fault or negligence of the buyer or third party. Use of unauthorized repair parts, or; modifications made to the TS1021 by the customer.
List Price: $724.64 Our Price: $557.61 You save $167.03! Availability:: available for order Product Code: BAPL-1989 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE TS1021 GENERAL PRESSURE WASHER PUMP 12/22/2011
Pressure Washer COMET PUMP LWD 2010 S - 6303.0306.00 Features:
List Price: $385.00 Our Price: $237.01 You save $147.99! Availability:: available for order Product Code: 6303.0306.00 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE LWD 2010 S 12/21/2011
Annovi reverberi Pressure Washer Pump RMW2.5G25D 2.5 GPM @ 2500 PSI, Axial Radial pumps that fit many 5 and 5-1/2 hp engines. See link for product details and replacement parts: RMW PARTS LIST
This plunger pump will pump up to 2.5 GPM at 2500 PSI. It spins at 3400 RPM in a direct drive system coupled with a gasoline engine. The matching flange provides convenient connection to most 7/8” shaft 1.1 – 5.5 HP engines. The hollow shafted pump includes a built-in pressure control valve, and chemical injection system.
We do not have any mfg cross reference information available. However, RMW pumps fit most vertical engines (pump under the motor) with a 7/8″ straight keyed shaft.
Annovi reverberi Pressure Washer Pump RMW2.5G25D pumps have a standard 22mm-14 twist connect outlet.
Best to choose RMW pump that has same or close to original pumps GPM & PSI. Significant changes to GPM may cause nozzle & motor problems.
Features of this Annovi reverberi Pressure Washer Pump RMW2.5G25D:
SKU: RMW2.5G25D
Brand: Annovi Reverberi – AR North America
AR RMW25G25D, RMW2.5G25D Vertical Radial-Axial series replacement pump (Mounts under the engine)
Fits most homeowner type vertical pressure washers with Front Mounted Pump (see 2nd image)
NOTE: This Pump DOES NOT fit Karcher units using a hex head bolt to drive the pump.
Built In unloader and chemical injector
Brass manifold
Stainless steel plungers
Pump comes with oil
Manifold: Forged brass for long term use.
Bolts: Three 6mm cadmium plated steel.
Plungers: Hardened stainless steel.
Valves: Stainless steel poppet, seat and cage, stainless steel spring.
Seals: Buna-N dual seals.
Bearings: Premium oversized ball and needle bearings.
Crankshaft: Precision die-cast, with cooling fins for maximum heat dissipation. The housing retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer
Annovi reverberi Pressure Washer Pump RMW2.5G25D
The Technical specifications of the Annovi reverberi Pressure Washer Pump RMW2.5G25D:
Vertical Mount with Gas Flange 3-6 HP
Max. Volume: 2.5 GPM
Max. Discharge Pressure: 2,500 PSI
Max. Pump Speed: 3,400 RPM
Shaft Diameter: 7/8” Hollow
Engine shafts longer than 2” will require spacers or washers
Maximum Horsepower Requirements: 5.8 GHP
Inlet Port: 3/4″ FGH (garden hose)
Outlet Port: 22mm (Twist Connect)
Weight: 7.7 lb
Annovi reverberi Pressure Washer Pump RMW2.5G25D
List Price: $307.66 Our Price: $196.39 You save $111.27! Availability:: available for order Product Code: RMW2.5G25D
PRICE SUBJECT TO CHANGE. PRICE VALID ON THIS RMW2.5G25D 12/20/2011.
