Tag: annovi reverberi pumps

• Max Flow (in GPM): 3.0
• Max Flow (in L/Min): 11.4
• Max Pressure (in PSI): 3500
• Max Bar: 240
• Power EBHP: 7.0
• Bore Dia: 15mm
• Stroke: 13.2mm
• Crankshaft ID Stamp: 3
• Pump Speed (in RPM): 1750
• Shaft Diameter: 1-1/8″ hollow

The SXMA3G35E-F17 AR Annovi Reverberi Pressure Washer Pump has the following Features:

• Manifold:
• – Forged Brass: Strength and no porosity equals long life. Higher hydrostatic pressures, safety and performance.
• – Inlet and Discharge Ports: Heavy bosses for added strength.
• – Offset Discharge Ports: High efficiency, smooth flow.
• – Bolts: Eight bolts, 6mm, grade 12.9.
• SXMA3G35E-F17 Valves:
• – Ultra Form Cages: Durability, strength and long life.
• – Poppets, Seat and Spring: 303 and 400 series stainless steel.
• – Valve Caps of the SXMA3G35E-F17: Machined brass – greater strength.
• Packing and Plungers:
• – High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
• – Low Pressure Seals: “U” cup double lip Buna-N, good positive seal.
• – Support Guides: Machined brass, two-piece construction to assure proper plunger alignment and to maximize packing and seal life.
• – Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
• Bearings: Over sized for maximum life and load disbursement, needle bearing on the drive side and ball on the non-drive side. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
• Crankcase on the SXMA3G35E-F17: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
• Rear Cover: precision die-cast, O-ring sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen).
• Plunger Rods of the SXMA3G35E-F17: Stainless steel construction for strength (no plating to scrape off). O-ring plunger sealing system.
• Rod Pins: Precision ground and hardened steel, over sized for load disbursement.
• Connecting Rods: One-piece special alloy aluminum based, over sized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
• Crankshaft: Forged, precision ground and hardened for extremely long life and durability.
• Oil Seals and O-rings: All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
• Oil Capacity: 14.5 oz., refer to parts breakdown.
• Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
• Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
• Hot Water: High temperature kits are available to 180º F. Refer to breakdown
• Wet End Repair: Very simple no special tools are required.
• Mounting Bolt Pattern: Same on the top and bottom of the crankcase for simple drive side change.
• Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.

List Price: $768.30
Our Price: $479.97 Click to order the SXMA3G35E-F17 AR Annovi Reverberi Pressure Washer Pump
You save $288.33!
Availability:: available for order
Product Code: SXMA3G35E-F17
Price Subject to change on the SXMA3G35E-F17 Pressure washer pump from Annovi Reverberi.

• Vertical Mount with Gas Flange 3-7 HP
• Max. Volume: 2.5 GPM
• Max. Discharge Pressure: 2,800 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 7/8” Hollow
• Built In unloader and chemical injector
• Built In easy start valve
• Maximum Horsepower Requirements: 6.5 GHP
• Inlet Port: 3/4″ FGH (garden hose)
• Outlet Port: 22mm (Twist Connect)
• Brass manifold
• Stainless steel plungers
• Pump comes with oil
• See optional items below
• Note: Engine shafts longer that 2” will require spacers or washers
• Weight: 7.7lb.

Is this RMW2.5G28-EZ not the right pressure washer pump?  Click the link to see all our RM Style Pressure Washer Pumps from Annovi Reverberi.

Click the link to order this RMW2.5G28-EZ

Availability:: available for order
Product Code: RMW2.5G28-EZ
Price subject to change.  Price valid on this RMW2.5G28-EZ AR Annovi Reverberi Pressure Washer Pump, Use code 5off for 5% off all orders over $50.00

• Max GPM………………2.5
• Max LMP…………………………9.5
• Max PSI………………….2500
• Max Bar………………………….170
• Power EBHP……………4.5
• Bore Dia. mm…………………….15
• Stroke mm……………….5.8
• Weight Lbs………………………..11
• Max Temp……………….140°
• Oil Capacity………………………4.5oz
• Inlet Thread ……………1/2”M
• Discharge Thread……………….22mm

This SJV2.5G25D-F7 AR Annovi Reverberi Pressure Washer Pump Features:

• Manifold of the SJV2.5G25D-F7:
• Forged Brass: Strength and no porosity – long life. Higher hydrostatic pressures – safety.
• Unloader: Built in to optimize performance while reducing setup time. Integral trap pressure, fixed or adjustable chemical injector.
• Bolts: Three bolts, 10mm, grade 8.8.
• Valves:
• Ultra Form Cages: Durable, strong, and long life. Unique inlet valve configuration: the valve cage incorporates the high pressure packing head ring.
• Poppets, Seat and Spring: 303 and 400 series stainless steel.
• Valve Caps of the SJV2.5G25D-F7: Machined brass for greater strength.
• Packing and Plungers:
• High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load. Continuously lubricating for extended life, self lubricating packing/Plunger guide support ring.
• Low-Pressure Seals: “U” cup double lip Buna-N for a good positive seat.
• Support and Guides: Machined brass, 1-piece construction to assure proper plunger alignment, maximize packing and seal life.
• Plungers: Coated ceramic stainless steel, strong and durable. The pump includes a plunger shoe to distribute the additional plunger load.
• Bearings: Angular contact ball bearing stabilizes the crankshaft and one thrust needle bearing absorbs the plunger load and assures long radial plate life. All of the thrust plates are made of heat treated hardened steel for extended life.
• Crankcase: Precision die-cast, large cooling fins and anodized for maximum heat dissipation. Sight glass, fill and drain plugs.
• Rear Cover: Precision die-cast, O-ring sealed. The housing on the SJV2.5G25D-F7 retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer.
• Crankshaft/Wobble Plate: Precision die-cast to assure proper stroke, duration and alignment.
• Oil Seals and O-rings: All are constructed of Buna-N rubber. The oil seals have stainless steel garder springs to assure constant tension on the sealing surface.
• Oil Capacity: 4.5 oz.
• Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
• Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
• Wet End Repair: Very simple no special tools required.
• Mounting Flanges: Gasoline SAE J609a flange. Refer to breakdown.
• Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.

List Price: $430.00
Our Price: $288.53 Click to purchase the SJV2.5G25D-F7 pressure washer pump HERE!
You save $141.47!
Availability:: available for order
Product Code: SJV2.5G25D-F7**
Price subject to change.  Price valid on the SJV2.5G25D-F7 pressure washer pump 9/24/2012

• Max GPM………………7
• Max LMP…………………………26.5
• Max PSI………………….5000
• Max Bar………………………….345
• Power EBHP……………24
• Bore Dia. mm…………………….18
• Stroke mm……………….21
• Weight Lbs………………………..35
• Max Temp……………….140°
• Oil Capacity………………………32oz
• Inlet Thread ……………1/2”F
• Discharge Thread……………….3/8”F

Items NOT INCLUDED with your SXWA7G50 AR Annovi Reverberi Pressure Washer Pump that you may need:

The PUMP GUARD will ‘dump’ any water above 145 degrees F. before it reaches your pump (saving you the trouble of rebuilding your pump)

PRESSURE REGULATOR / UNLOADER – if we list one to the right of the pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.

The INLET WATER FILTER will catch most small debris before it enters your pump

The EZ-START VALVE will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer

The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your pump!

PUMP OIL, you can never have enough on hand! Many pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.

List Price: $1,574.48
Our Price: $976.25

You save $598.23!
Availability:: available for order
Product Code: SXWA7G50
Price Subject to change.  Price valid on the SXWA7G50 AR Annovi Reverberi Pressure Washer Pump 9/10/2012

• Maximum volume: 2.9 GPM
• Maximum discharge pressure: 2,500 PSI
• Maximum pump speed: 1,450 RPM
• Shaft diameter: 24 mm solid
• Maximum horsepower requirements: 5.0 BHP
• Maximum fluid temperature: 185ºF.
• Inlet ports (2): 1/2″ FPT
• Discharge ports (2): 3/8″ FPT
• Drive side: Standard right
• Weight: 14.0 lb.

List Price: $1,364.46
Our Price: $778.80 Click the link to order the XHW11.17N Pressure Washer Pump from Annovi Reverberi
You save $585.66!

Availability:: available for order
Product Code: XHW11.17N
Price subject to change.  Price valid on the XHW11.17N – 6/27/2012

• Max GPM……………… 5.8
• Max LMP………………………… 22
• Max PSI…………………. 7250
• Max Bar…………………………. 500
• Power EBHP…………… 27
• Bore Dia. mm……………………. 18
• Stroke mm………………. 21
• Weight Lbs……………………….. 29
• Max Temp………………. 140°
• Oil Capacity……………………… 32oz
• Inlet Thread …………… 1/2”F
• Discharge Thread………………. 3/8”F

Is the SHP22.50HN not the right SHP Pressure washer pump for you?  Click the link to see all our SHP Pressure washer pumps from Annovi Reverberi.

List Price: $2,910.90
Our Price: $1,798.95 Click to order the SHP22.50HS Pressure washer pump
You save $1,111.95!
Availability:: available for order
Product Code: SHP22.50HN
Price subject to change.  Price valid on the SHP22.50HN – 6/20/2012

• Max GPM……………… 2.37
• Max LMP………………………… 9.0
• Max PSI…………………. 2000
• Max Bar…………………………. 140
• Power EBHP…………… 3.3
• Bore Dia. mm……………………. 18
• Stroke mm………………. 8.4
• Weight Lbs……………………….. 11
• Max Temp………………. 140°
• Oil Capacity……………………… 10oz
• Inlet Thread …………… 1/2”F
• Discharge Thread………………. 3/8”F

XT9.14N AR (Annovi Reverberi) Pump 2.37 GPM @ 2000 PSI.

XT9.14N Plunger Pumps are designed for a wide variety of moderate pressure washing applications. They are constructed with die-cast bodies and feature a brass head. Internal components include special thick solid ceramic plungers for long life and durability. Precision cast cooling fins are anodized for maximum heat dissipation. Oversized needle bearing on the drive sides and ball bearings on the non-drive side assure proper shaft alignment and maximum life. Valve cages of special designed Ultra-Form impervious to water absorption provide positive seating and extended life. One-piece connecting rods are either a special alloy aluminum or bronze at higher pressures, oversized for strength and load disbursement.

The AR Annovi Reverberi Pressure Washer Pump XT9.14N Features:

• Manifold:
• – Forged Brass: Strength and no porosity equals long life. Higher hydrostatic pressures, safety, performance.
• – Inlet and Discharge Ports: Heavy bosses for added strength.
• – Offset Discharge Ports: High efficiency, smooth flow.
• – Bolts: Six Bolts, 6mm, grade 12.9.
• Valves:
• – Ultra Form Cages: Durability, strength and long life.
• – Poppets, Seat and Spring: 303 and 400 series stainless steel.
• – Valve Caps: Machined brass – greater strength.
• Packing and Plungers:
• – High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
• – Low Pressure Seals: “U” cup double lip Buna-N. Good positive seal.
• – Support Guides: Machined brass one-piece construction to assure proper plunger alignment and to maximize packing and seal life.
• – Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
• Bearings: Oversized for maximum life and load disbursement, two ball bearings on the solid shaft series and a needle bearing on the drive side and ball on the non-drive side for the hollow shaft series. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
• Crankcase: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
• Rear Cover: Precision die-cast, precision punched gasket sealed and bayonet style sightglass for positive sealing and locking (no threads to loosen).
• Plunger Rods: Stainless steel construction for strength (no plating to scrape off). O-ring plunger sealing system.
• Rod Pins: Precision ground and hardened steel,
• oversized for load disbursement.
• Connection Rods: One piece special alloy aluminum based and bronze, oversized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
• Crankshaft: Forged one-piece, precision ground and hardened for extremely long life and durability.
• Oil Seals and O-rings: All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
• Oil Capacity: Flat cover 8 oz. and extended cover 10 oz.
• Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
• Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
• Hot Water: High temperature kits are available to 180º F. Refer to breakdown.
• Wet End Repair: Very simple no special tools are required.
• Mounting Bolt Pattern: Same on the top and bottom of the crankcase for simple drive side change.
• Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.

Is the AR Annovi Reverberi Pressure Washer Pump XT9.14N not the right pressure washer pump for you?  Click the link to see more Pressure washer pumps from Annovi Reverberi.

List Price: $571.65
Our Price: $358.91 Click the link to order this Pressure washer pump XT9.14N
You save $212.74!

Availability:: available for order
Product Code: XT9.14N

Price subject to change.  Price valid on thie XT9.14N pressure washer pump 6/6/2012

• Max GPM………………11
• Max LMP…………………………42
• Max PSI………………….2200
• Max Bar………………………….150
• Power EBHP……………15
• Bore Dia. mm…………………….28
• Stroke mm……………….17.2
• Weight Lbs………………………..36
• Max Temp……………….140°
• Oil Capacity………………………32oz
• Inlet Thread ……………3/4”F
• Discharge Thread……………….3/8”F

The Pressure Washer Pump XWL-SS42.15N Features:

• Manifold:
• – 316L – Stainless Steel Block Style: Strength and no porposity = long life.
• – Inlet and Discharge Ports: 1/2” inlet and 3/8” discharge.
• – Offset Discharge Ports: High efficiency, smooth flow
• – Bolts: 8 Bolts, 10mm, stainless steel.
• Valves:
• – Ultra Form Cages: Durable, strength, and long life.
• – Poppets, Seat and Spring: 316 series stainless steel.
• – Valve Caps: Machined 316L series stainless steel.
• Packing and Plungers:
• – High Pressure Packing: “Special profile” style (W-1) Viton (cotton duct weave base) strong and tightens under load.
• – Low Pressure Seals: “W-2” style Viton, good positive seal.
• – Support and Guides: Machined stainless steel, 1-piece construction with intermediate and guide rings to assure proper plunger alignment, maximize packing and seal life.
• – Plungers: Special aluminum oxide blend, solid ceramic long life, strong and durable. Ultra thick with a locating step and SST retaining bolts.
• Bearings: Premium oversized taper for maximum life and load dispersement.
• Bearings Supports: Precision die-cast and machined to assure concentricity and alignment.
• Crankcase: Precision die-cast, large cooling fins and covered with a special anti-corrosion finish.
• Rear Cover: Precision die-cast, O-Ring sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen). This is an “AR” orginal. Oil drain plug.
• Plunger Rods: Stainless steel construction for strength, back-up and O-ring plunger sealing system.
• Special acorn style retaining nuts and SST slingers.
• Rod Pins: Precision ground and hardened steel, oversized for load dispersement.
• Connection Rods: 2-piece special alloy bronze for higher pressures, oversized for maximum strength, load dispersement, and life. Heavy pin area construction.
• Crankshaft: Forged, precision ground and hardened for extremely long life and durability. Available in 24mm solid shaft for gearbox drives. Shaft key set screws are standard on high-speed version for long shaft life.
• Oil Seals and O-Rings: Triple lip oil seals, long life and much less leak prone. All are constructed of Buna-N rubber. The O-Rings have stainless steel garder springs for assure constant tension on the sealing surface.
• Oil Drains: Quantity of 2. One in the rear cover and one in the bottom of the crankcase.
• Oil Capacity: 32 oz.
• Oil Sight Glasses: Rear cover and non-drive side bearing housing.
• Dyno Proven: All pumps are dyno tested to assure the theroretical design meets the actual design.
• Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
• Hot Water: High temperature kits are available to 180°F.
• Wet End Repair: Very simple no special tools are required.
• Mounting Flanges: Multiple flanges are available.
• Buna-N: Elastomers available.

Is this not the right pressure washer pump?  Click the link to see all our XW Stainless Steel Series pressure washer pumps.

List Price: $5,356.49
Our Price: $3,304.46 Click the link to order this XWL-SS42.15N Pressure Washer Pump
You save $2,052.03!
Availability:: available for order
Product Code: XWL-SS42.15N
Price subject to change.  Price valid on this XWL-SS42.15N – 6/4/2012