Spotlight on the AR Annovi Reverberi Pressure Washer Pump RMV2G25D.
RMV2G25D AR (Annovi Reverberi) Pump 2 GPM @ 2500 PSI
This RMV2G25D plunger pump will pump up to 2 GPM at 2500 PSI. It spins at 3400 RPM in a direct drive system coupled with a gasoline engine. The matching flange provides convenient connection to most 3/4” shaft 1.1 – 5.5 HP engines. The hollow shafted RMV2G25D pump includes a built-in pressure control valve, and chemical injection system.
AR Annovi Reverberi Pressure Washer Pump RMV2G25D
The AR Annovi Reverberi Pressure Washer Pump RMV2G25D Features:
Manifold: High strength forged brass for long term use.
Bolts: Three 6mm cadmium plated steel.
Plungers: Hardened stainless steel.
Valves: Stainless steel poppet, seat and cage, stainless steel spring.
Seals: Buna-N dual seals.
Bearings: Premium oversized ball and needle bearings.
Crankshaft: Precision die-cast, with cooling fins for maximum heat dissipation. The housing retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer.
AR Annovi Reverberi Pressure Washer Pump RMV2G25D
The AR Annovi Reverberi Pressure Washer Pump RMV2G25D has the following Technical Specifications:
Max GPM……………… 2
Max LMP………………………… 7.6
Max PSI…………………. 2500
Max Bar…………………………. 172
Power EBHP…………… 3.4
Bore Dia. mm……………………. 12
Stroke mm………………. 8.3
Weight Lbs……………………….. 7.5
Max Temp………………. 140°
Oil Capacity……………………… 2.2oz
Inlet Thread …………… 3/4”
GH Discharge Thread………………. 22mm
Annovi Reverberi Pressure Washer Pump
List Price: $307.66 Our Price: $196.39 CLICK RMV2G25D TO ORDER You save $111.27! Availability:: available for order Product Code: RMV2G25D PRICE SUBJECT TO CHANGE. PRICE VALID ON THE AR Annovi Reverberi Pressure Washer Pump RMV2G25D – 1/19/2012
Oil Capacity = 4.5 oz, Maximum Fluid Temperature = 140° F, Inlet Thread = 1/2”M, Discharge Thread = 3/8”M
SPECIAL NOTE: Use only AR64545 (click link to view/purchase oit) for the XJ/SJ/BK Series pumps only: Do NOT change oil. Use oil only to add if low. This oil is a specially formulated synthetic with special additives for the demands of the XJ, SJ and BK pump series. No other oil is factory approved for these pumps, and could result in pump failure.
This AR XJW24G24D-F27 pump is designed for medium duty loads. It spins at 3400 RPM in a direct drive system coupled with a gasoline engine, the matching flange provides convenient connections to most 3/4” shaft 3.5 – 6.5 HP engines. Optional vertical and horizontal setups. Precision die-cast crankcase with large cooling fins for maximum heat dissipation. Seals and V-Packings designed to continuously lubricate for extended life. The XJW24G24D-F27 has a Built-in unloader to optimize performance while reducing setup time. Integral trap pressure with fixed or adjustable chemical injector.
AR Annovi Reverberi Pressure Washer Pump XJW24G24D-F27
The AR Annovi Reverberi Pressure Washer Pump XJW24G24D-F27 has the following specifications:
Max GPM………………2.4
Max LMP…………………………9
Max PSI………………….2400
Max Bar………………………….166
Power EBHP……………3.9
Bore Dia. mm…………………….15
Stroke mm……………….5.8
Weight Lbs………………………..11
Max Temp……………….140°
Oil Capacity………………………4.5oz
Inlet Thread ……………1/2”M
Discharge Thread……………….3/8”M
XJW24G24D-F27 Pump Exploded View
The AR Annovi Reverberi Pressure Washer Pump XJW24G24D-F27 Features:
Manifold:
– Forged Brass: Strength and no porosity – long life. Higher hydrostatic pressures – safety.
– Unloader: Built in to optimize performance while reducing setup time. Integral trap pressure, fixed or adjustable chemical injector.
– Bolts: Three bolts, 10mm, grade 8.8.
Valves:
– Ultra Form Cages: Durable, strong, and long life. Unique inlet valve configuration: the valve cage incorporates the high pressure packing head ring.
– Poppets, Seat and Spring: 303 and 400 series stainless steel.
– Valve Caps: Machined brass for greater strength.
Packing and Plungers:
– High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load. Continuously lubricating for extended life, self lubricating packing/Plunger guide support ring.
– Low-Pressure Seals: “U” cup double lip Buna-N for a good positive seat.
– Support and Guides: Machined brass, 1-piece construction to assure proper plunger alignment, maximize packing and seal life.
– Plungers: Coated ceramic stainless steel, strong and durable. The pump includes a plunger shoe to distribute the additional plunger load.
Bearings: Angular contact ball bearing stabilizes the crankshaft and one thrust needle bearing absorbs the plunger load and assures long radial plate life. All of the thrust plates are made of heat treated hardened steel for extended life.
Crankcase: Precision die-cast, large cooling fins and anodized for maximum heat dissipation. Sight glass, fill and drain plugs.
Rear Cover: Precision die-cast, O-ring sealed. The housing retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer.
Crankshaft/Wobble Plate: Precision die-cast to assure proper stroke, duration and alignment.
Oil Seals and O-rings: All are constructed of Buna-N rubber. The oil seals have stainless steel garder springs to assure constant tension on the sealing surface.
Oil Capacity: 4.5 oz.
Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
Wet End Repair: Very simple no special tools required.
Mounting Flanges: Gasoline SAE J609a flange. Refer to breakdown.
Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.
List Price: $484.10 Our Price: $305.01 You save $179.09! Availability:: available for order Product Code: XJW24G24D-F27 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE XJW24G24D-F27 – 1/18/2012
Spotlight on MV540 UNLOADER 8GPM 2600PSI. To purchase this unloader click here.
The MV540 UNLOADER Features:
Maximum Pressure: 2500 PSI
Maximum flow: 8 GPM
Maximum temperature: 250 F
Inlet: 3/8″ MPT
Outlet: 3/8″ MPT
Bypass: 3/8″ FPT
Weight: 20 oz
MV540 UNLOADER
Is this UNLOADER not the right unloader for you? Check out all our unloaders here.
List Price: $48.70 Our Price: $37.47 You save $11.23! Availability:: available for order Product Code: BAPL-1650 PRICE SUBJECT TO CHANGE. PRICE VALID ON THIS UNLOADER – 1/17/2011
ORDERING INFORMATION for the CAT Pump 6013:
A pre-charge different from factory (indicate desired pre-charge on purchase order)
Note: A handling charge will apply.
CAT Pump 6013 Prrrrr-O-Lator Pulsation Dampener
This CAT Pump 6013 Prrrrr-O-Lator Pulsation Dampener Features:
Nitrogen precharged to eliminate moisture and bladder deterioration.
Broader bladder design provides greater pulsation reduction for smoother performance and longer system component life.
316 Stainless Steel housing for critical applications.
Sealed valve for positive pressure lock.
Pre-charged Prrrrr-O-Lators are defined as hazardous articles. Uncharged CAT Pump 6013 Prrrrr-O-Lators requires no special handling and can be shipped via standard shipping methods.
All domestic shipments of hazardous articles must follow Department of Transportation CFR 49, parts 100 to 185 regulations (DOT).
International shipments of hazardous articles must follow either International Air Transport Association regulation (IATA) or International Maritime Dangerous Goods Codes (IMDG).
CAT Pump 6013 Prrrrr-O-Lator Pulsation Dampener
This CAT Pump 6013 Prrrrr-O-Lator Pulsation Dampener has the following specifications:
MODEL 6013 – Rechargeable
Maximum Flow……………………………………………….40 gpm (151 lpm)
Maximum Working Pressure………………………..2000 psi (140 bar)
Precharge…………………………………………………………..450 psi (30 bar)
Temperature Range………………………………..+5° to 300°F (–15 to 149°C)
Volume……………………………………………………………45 cu. in. (0.74 l)
Safety Factor……………………………………………………………4/1 (4/1)
Bladder Construction…………………………………………..FPM (FPM)
Port Size…………………………………………………………..1” NPTM (1” NPTM)
Diameter………………………………………………………………..4.44” (113 mm)
Length……………………………………………………………………7.79” (198 mm)
Weight………………………………………………………………6.28 lbs. (2.8 kg)
List Price: $2,151.00 Our Price: $2,151.00 Call 1-877-824-7763 {for a better price} HazMat Fee $20.00 Availability:: Available for Order Product Code: 6013 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE CAT PUMP 6013 PRRRRR-O-LATOR PULSATION DAMPENER 1/16/2012
Tamper resistant operator adjustable valve which allows limit setting on both maximum and minimum pressure
Ideal for steam combination applications
Straight flow-through design minimizes pressure loss through valve
Working components of the ST-261-I UNLOADER constructed of high grade stainless steel, teflon, and Viton seals for maximum heat/chemical resistance
Internal bypass valve can be easily accessed and repaired without removing unloader from unit
True to Suttner design tradition, valve is cartridge type and installed in minutes
Pressure adjustment knob on the ST-261-I UNLOADER can be removed if desired
ST-261-I UNLOADER
The ST-261-I UNLOADER has the following specifications:
Downstream injection at 10:1 ratio
Low pressure limit setting eliminates need of additional metering devices
Relies on pressure loss through a restrictive orifice, which is built-in on the ST-261. Restriction AFTER the orifice must be minimized in order for injection to occur. Therefore, this system must incorporate a large orifice spray nozzle which reduces such restriction. The usage of a nozzle with a minimum orifice size of 30.0 is recommended. A smaller nozzle could be used, but the added restriction may result in ineffective suction rates or no suction at all. In addition, remember that elbows, fittings, and even hose add to the restriction within the system and may affect or eliminate the suction capabilities
Pressure Range: Up to 3650 PSI
Flow Range: 3.35 GPM to 5.0 GPM
Temperature: 176 F
Inlet: 3/8″ FPT
Outlet: 3/8″ FPT
Bypass: 1/4″ FPT
Gauge Port: 1/4″ FPT
Weight: 22.5 oz
List Price: $72.52 Our Price: $55.80 You save $16.72! Availability:: available for order Product Code: BAPL-1397 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE ST-261-I UNLOADER – 1/13/2012
The PA VB3KTT UNLOADER is a Compact pressure trapping unloader.
The PA VB3KTT UNLOADER Features:
Forged brass body with stainless wetted parts
Hexagonal check for improved reliability
Locking ring limits maximum pressure setting
PA VB3KTT UNLOADER
The PA VB3KTT UNLOADER has the following technical specifications:
6.5 GPM maximum
3650 PSI maximum
195 F. maximum
1/4″ MPT inlet
3/8″ MPT outlet
3/8″ FPT bypass
List Price: $42.60 Our Price: $32.78 You save $9.82! Availability:: available for order Product Code: BAPL-6017 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE PA VB3KTT UNLOADER – 1/1/2012
The repair Manual for the Giant Pressure Washer Pump P313 can be found by clicking here.
GIANT Pressure Washer PUMP P313
INSTALLATION INSTRUCTIONS FOR THE GIANT Pressure Washer PUMP P313
Installation of the Giant Industries, Inc., pump is not a complicated procedure, but there are some basic steps common to all pumps. The following information is to be considered as a general outline for installation. If you have unique requirements, please contact Giant Industries, Inc. or your local distributor for assistance.
1. The P313 pump should be installed flat on a base to a maximum of a 15 degree angle of inclination to ensure optimum lubrication.
2. The inlet to the P313 pump should be sized for the flow rate of the pump with no unnecessary restrictions that can cause cavitation. Teflon tape should be used to seal all joints. If pumps are to be operated at temperatures in excess of 1600 F, it is important to insure a positive head to the pump to prevent cavitation.
3. The discharge plumbing from the pump should be properly sized to the flow rate to prevent line pressure loss to the work area. It is essential to provide a safety bypass valve between the pump and the work area to protect the pump from pressure spikes in the event of a blockage or the use of a shut-off gun.
4. Use of a dampener is necessary to minimize pulsation at drive elements, plumbing, connections, and other system areas. The use of a dampener with Giant Industries, Inc. pumps is optional, although recommended by Giant Industries, Inc. to further reduce system pulsation. Dampeners can also reduce the severity of pressure spikes that occur in systems using a shut-off gun. A dampener must be positioned downstream from the unloader.
5. When viewed from the side of the P313 pump, crankshaft rotation is clockwise on pumps with left handed shafts and counterclockwise on pumps with right handed shafts. Reverse rotation may be safely achieved by following a few guidelines available upon request from Giant Industries, Inc. Required horsepower for system operation can be obtained from the charts on pages 3-7 and 10.
6. Before beginning operation of your pumping system, remember: Check that the crankcase and seal areas have been properly lubricated per recommended schedules. Do not run the P313 pump dry for extended periods of time. Cavitation will result in severe damage. Always remember to check that all plumbing valves are open and that pumped media can flow freely to the inlet of the P313 pump.
List Price: $1,008.31 Our Price: $924.01 You save $84.30! Availability:: available for order Product Code: LAN-8.702-356.0 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE GIANT PRESSURE WASHER PUMP P313 – 1/09/2012
CAT Pump Prrrrr-O-Lator 6011, Rechargeable Pulsation Dampener has the following specifications:
Maximum Flow ………………………………………..25 GPM* (95 L/M)
Maximum Working Pressure………………….7200 PSI*** (500 BAR)
Precharge ………………………………………………2000 PSI (140 BAR)
Bladder Construction………………………………………NBR (NBR)
Maximum Operating Temperature ………………180°F*** (82°C)
Volume……………………………………………………15 cu. in. (0.25 L)
Safety Factor …………………………………………………..4/1 (4/1)
Port Size……………………………………………….1/2″ NPTF (1/2″ NPTF)
Diameter ………………………………………………………..4.5″ (115 mm)
Length………………………………………………………….5.59″ (142 mm)
Weight ………………………………………………………6.4 lbs. (2.9 kg)
*Authorized system performance. Contact CAT PUMPS for continuous duty performance.
**2500 PSI maximum working pressure at 180°F temperature.
***6000 PSI maximum working pressure at 180°F temperature.
NOTE: To order a different prechage than stated, add .800 to model number and specify desired precharge.
Material Codes (Not Part of Part Number): NBR=Medium Nitrile (Buna-N)
Pulsation DampenersNOTE: Prrrrr-O-Lators with pre-charge are considered hazardous commodities and require special labeling, documentation and additional transportation surcharges. When ordering pre-chargeable models, add .800 to part number and specify no pre-charge to ship via standard methods.
FOR The CAT PUMP 6011 Product Data Sheet CLICK HERE.
List Price: $1,866.00 Our Price: $1,866.00 HazMat Fee $20.00 Call 1-877-824-7763 {For a better Price} Availability:: Available for Order Product Code: 6011 PRICE SUBJECT TO CHANGE. PRICE VALID ON THE CAT PUMP 6011 – 1/06/2012
Spotlight on GENERAL PRESSURE WASHER PUMP,TS1021L SERIES 47
The TS1021L is the preferred pump frame in the pressure cleaning industry
• Forged brass manifold with an exclusive lifetime warranty
• Large-capacity, die-cast, anodized aluminum oil-bath crankcase
• Over-sized connecting rods for maximum life
• Heavy-duty tapered roller bearing.
• Solid ceramic plungers with continuously lubricated packings
• Unitized stainless steel inlet and discharge valves
• Available in left-handed “L” version
GENERAL PRESSURE WASHER PUMP,TS1021L SERIES 47
The GENERAL PRESSURE WASHER PUMP,TS1021L SERIES 47 Features:
General 47 Series Triplex Plunger Pump (left Handed)
Solid Shaft for Belt or Gear Drive
Max. Volume: 5.6 GPM
Max. Discharge Pressure: 1,700 PSI
Max. Pump Speed: 1450 RPM
Shaft Diameter: 24mm Solid
Max. Horsepower Requirements: 9.0 GHP
Max. Fluid Temp.: 165 degrees F.
Inlet Ports (2): 1/2″ BSP
Discharge Ports (2): 3/8″ BSP
Drive Side: Left
Forged brass head & valve covers
Solid ceramic plungers
Weight: 32.0 lb.
TS1021L Pressure Washer Pump
List Price: $1,206.90 Our Price: $631.52 You save $575.38! Availability:: available for order Product Code: TS1021L PRICE SUBJECT TO CHANGE. PRICE VALID ON THE GENERAL PRESSURE WASHER PUMP TS1021L – 1/5/2012
