Direct-Drive Misting Motor-Pump-Units CAT Pump 1CX05ELS.MIST ( 1CX05ELSPD501 ) and 8182 Motor (1/2HP, 1PH) Pulse Hose
OPERATION:
A pressure regulator is included with each 1CX plunger pump. The regulator is not pre-set at the factory. Set system pressure once the system is started. Start at the lowest pressure reading and adjust the hex adjusting cap in small increments until the desired system pressure is attained. Remember to service the regulator on the same schedule as the pump seals and valves. Refer to 1CX service manual for start-up, servicing of seals and valves, torque requirements and diagnosis/maintenance chart.
INLET:
It is recommended to install a flexible hose at the pump inlet. Assure flooded or up to 60 psi inlet pressure for optimium
performance. Install an inlet filter to remove standard water debris.
DISCHARGE:
All discharge plumbing for the 1CX pump connects to the
regulator outlet port.
PULSE HOSE MOUNTING:
Mount the pulse hose by installing a tee fitting into the regulator outlet port. Install the pulse hose into the top port. Coil hose and tie wrap as shown. Add nipple with a tee to mount pressure gauge. The other end of the pulse hose is plugged to capture the pulse.
Note: Without a pulse hose, the pump may draw as much as 2 additional AMPS above full load AMPS.
BY-PASS: The regulator by-pass is at the bottom. Connect a 1/4” flexible hose and route to inlet of pump, to tank, or to drain.
NOTICE: By-pass to the pump inlet is designed for cold water or ambient temperature operation.
DO NOT EXCEED 6 MINUTES IN BY-PASS operation. Excessive temperatures will cause premature wear or damage to the pump and VOID THE WARRANTY.
CAT Pump 1CX05ELS.MIST ( 1CX05ELSPD501 )
CAT Pump 1CX05ELS.MIST ( 1CX05ELSPD501 ) exploded view
Click here for the 1CX05ELS.MIST ( 1CX05ELSPD501) CAT Pump Parts Breakdown.
The CAT Pump 1CX05ELS.MIST ( 1CX05ELSPD501 ) Features:
- Ultra-compact, direct-drive motor-pump-unit for portability and small spaces.
- Four-postion head mounting for plumbing flexibility.
- Industrial stacked valves provide easy servicing.
- Concentric ceramic plunger and specially formulated seals provide extended seal life.
- Oil bath lubrication assures optimum drive-end lubrication.
- Pressure regulator offers precision pressure setting and over-pressure protection.
- Pulse Hose minimizes pulsation and lowers amp draw.
This CAT Pump 1CX05ELS.MIST ( 1CX05ELSPD501 ) has the following specs:
- Maximum RPM………………………………1725 rpm (1725 rpm)
- Inlet Pressure Range…………..Flooded to 60 psi (Flooded to 4 bar)
- Bore………………………………………………….0.630” (16 mm)
- Crankcase Capacity………………………….2.03 oz. (0.06 l)
- Maximum Liquid Temperature……..up to 140°F (up to 60°C)
- Inlet Port………………………………………3/8” NPTF (3/8” NPTF)
- Discharge Port……………………………..1/4” NPTF (1/4” NPTF)
- By-Pass Port………………………………..1/4” NPTF (1/4” NPTF)
- Shaft Diameter………………………………………1/2” (12.7 mm)
- Weight (Pump Only)…………………………..3.4 lbs. (1.5 kg)
- Dimensions (Pump Only)…….3.62 x 5.12 x 6.85” (92 x 130 x 174 mm)
- PUMP MODEL 1CX05ELS.MIST
- Flow………………………………………………….0.50 gpm (1.89 lpm)
- Pressure Range…………………………100 to 1000 psi (7 to 70 bar)
- Stroke (Single Plunger)…………………………….0.248” (6.3 mm)
List Price: $745.00 
Call 1-877-824-7763 or email for a better price
Availability:: available for order
Product Code: 1CX05ELSPD501
PRICE SUBJECT TO CHANGE. PRICE VALID 10/13/2010
