LANDA – CAT PUMP 1LX100 (1.0/500, 1725 RPM) – 8.702-383.0
The LANDA – CAT PUMP 1LX100 (1.0/500, 1725 RPM) – 8.702-383.0 Features
- Low amp draw for compatibility with portable machines.
- Smooth, quiet operation for sound sensitive areas.
- Special Hi-Pressure and Lo-Pressure Seals offer exceptional life.
- RTP heat resistant liquid-end and Regulator.
- Mechanically actuated plungers offer greater efficiency.
- Optional direct-coupled motors for compact, easy assembly or convenient belt-drive mounting.
- Ready for initial start-up with oil in the crankcase.
LANDA - CAT PUMP 1LX100 (1.0/500, 1725 RPM) - 8.702-383.0
CAT PUMP 1LX100 parts breakdown Click here —> 
This LANDA – CAT PUMP 1LX100 (1.0/500, 1725 RPM) – 8.702-383.0 has the following technical specifications:
- Flow ………………………………………………….1.0 GPM (3.8 L/M)
- Stroke……………………………………………………..0.29″ (7.4 mm)
- Max. Discharge Pressure ……………………..500 PSI (35 BAR)
- Inlet Pressure Range ……………..Flooded to +20 PSI (Flooded to +1.4 BAR)
- RPM ………………………………………………1725 RPM (1725 RPM)
- Bore………………………………………………………..0.47″ (12 mm)
- Crankcase Capacity ……………………………..2.23 oz. (66 ml)
- Max. Liquid Temperature …………………………160°F (71°C)
- Inlet Fitting (1)…………………………………..3/8″ NPTF (3/8″ NPTF)
- By-Pass Ports (1)………………………………1/4″ NPTF (1/4″ NPTF)
- Discharge Ports (1)……………………………1/4″ NPTF (1/4″ NPTF)
- Discharge Fitting (1LXXC100 Only)……..3/8″ NPTF (3/8″ NPTF)
- Weight………………………………………………..2.65 lbs. (1.2 kg)
- Dimensions………………………………..4.4 x 3.2 x 8.4″ (112 x 81 x 212 mm)
LANDA - CAT PUMP 1LX100 (1.0/500, 1725 RPM) - 8.702-383.0
List Price: $565.84
Our Price: $424.06 
You save $141.78!
Availability:: available for order
Product Code: LAN-8.702-383.0 (CAT PUMP 1LX100)
PRICE SUBJECT TO CHANGE. PRICE VALID 10/25/2011
INSTALLATION ON THIS CAT PUMP 1LX100:
Each CAT PUMP 1LX100 comes with oil in the crankcase ready for start-up. CAT PUMPS special premium grade, multi-viscosity crankcase oil should be used. It is recommended to install this pump in a horizontal position with the oil filler cap at the top. It is permissible to rotate the oil filler cap to the right or left, however, some oil spitting may occur. A rubber plug is inserted into the oil filler cap for shipping. This should be removed before operation. Do not operate pump with plug in cap. Flexible hose should be installed at the unloader ports. Connect a hose equal to or one size larger than the inlet port at the bottom of the pump body. Connect a high pressure hose to the regulator discharge port at the side of the regulator. Connect a by-pass hose to the bottom port of the regulator or unloader and run to drain or back to a “T” in the inlet line. CAUTION: Do not over tighten the RTP pump or regulator body.
OPERATION of the CAT PUMP 1LX100:
Once the inlet water supply is turned on and the pump is started, adjust the regulator at the top with an allen wrench or turn adjusting cap on the unloader to set system pressure. Do this in small increments until the desired system operating pressure is reached. The CAT PUMP 1LX100 are axial plunger pumps. Special direct-drive motors are secured to the pump with a V-Clamp Mounting. The optional Drive Mount Assembly is required for the belt drive 1LXB100 model. The motor on the CAT PUMP 1LX100 rotates the offset cam and guide plate which is connected to the three plungers. Each plunger moves forward at a different stage of the cam rotation, providing a smooth, forward, liquid flow through the pump. On the back stroke, the liquid enters the inlet chamber and flows through each inlet valve. As the forward stroke begins, the inlet valve closes. On the forward stroke, the liquid goes through the seat and forces the discharge valve open to allow the liquid out the regulator discharge port.
