AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump
XJV-E22G24D-F7 AR (Annovi Reverberi) Pump 2.2 GPM @ 2400 PSI
This AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump is designed for medium duty loads. The AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump spins at 3400 RPM in a direct drive system coupled with a gasoline engine, the matching flange provides convenient connections to most 3/4” shaft 3.5 – 6.5 HP engines. The AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump has optional vertical and horizontal setups. Precision die-cast crankcase with large cooling fins for maximum heat dissipation. Seals and V-Packings designed to continuously lubricate for extended life. Built-in unloader to optimize performance while reducing setup time. Integral trap pressure with fixed or adjustable chemical injector.
This AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump Features:
- Manifold:
- – Forged Brass: Strength and no porosity – long life. Higher hydrostatic pressures – safety.
- – Unloader: Built in to optimize performance while reducing setup time. Integral trap pressure, fixed or adjustable chemical injector.
- – Bolts: Three bolts, 10mm, grade 8.8.
- Valves:
- – Ultra Form Cages: Durable, strong, and long life. Unique inlet valve configuration: the valve cage incorporates the high pressure packing head ring.
- – Poppets, Seat and Spring: 303 and 400 series stainless steel.
- – Valve Caps: Machined brass for greater strength.
- Packing and Plungers:
- – High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load. Continuously lubricating for extended life, self lubricating packing/Plunger guide support ring.
- – Low-Pressure Seals: “U” cup double lip Buna-N for a good positive seat.
- – Support and Guides: Machined brass, 1-piece construction to assure proper plunger alignment, maximize packing and seal life.
- – Plungers: Coated ceramic stainless steel, strong and durable. The pump includes a plunger shoe to distribute the additional plunger load.
- Bearings: Angular contact ball bearing stabilizes the crankshaft and one thrust needle bearing absorbs the plunger load and assures long radial plate life. All of the thrust plates are made of heat treated hardened steel for extended life.
- Crankcase: Precision die-cast, large cooling fins and anodized for maximum heat dissipation. Sight glass, fill and drain plugs.
- Rear Cover: Precision die-cast, O-ring sealed. The housing retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer.
- Crankshaft/Wobble Plate: Precision die-cast to assure proper stroke, duration and alignment.
- Oil Seals and O-rings: All are constructed of Buna-N rubber. The oil seals have stainless steel garder springs to assure constant tension on the sealing surface.
- Oil Capacity: 4.5 oz.
- Dyno Proven: All AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump are dyno tested to assure the theoretical design meets the actual design.
- Valve Design: Each AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump series has a valve design that optimizes its highest efficiency.
- Wet End Repair: Very simple no special tools required.
- Mounting Flanges: Gasoline SAE J609a flange. Refer to breakdown.
- Design: Using advanced fluid handling design programs. Overall AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump efficiency is increased.
The AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump has the following Specifications:
- Max GPM………………2.2
- Max LMP…………………………8.3
- Max PSI………………….2400
- Max Bar………………………….166
- Power EBHP……………3.5
- Bore Dia. mm…………………….15
- Stroke mm……………….5.8
- Weight Lbs………………………..11
- Max Temp……………….140°
- Oil Capacity………………………4.5oz
- Inlet Thread ……………1/2”M
- Discharge Thread……………….3/8”M
AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump
Click here for the AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump Parts Break Down.
Items NOT INCLUDED with your AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!
The PUMP GUARD will ‘dump’ any water above 145 degrees F. before it reaches your AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump (saving you the trouble of rebuilding your AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump).
PRESSURE REGULATOR / UNLOADER – if we list one to the right of the pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.
The INLET WATER FILTER will catch most small debris before it enters your AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump.
The EZ-START VALVE will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer
The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your pump!
PUMP OIL, you can never have enough on hand! Many pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.
Our Price: $251.63
You save $123.37!
Availability:: available for order
Product Code: XJV-E22G24D-F7
Annovi Reverberi Pressure Washer Pump
PRICE SUBJECT TO CHANGE. PRICE VALID on this AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump 11/03/2011
