Spotlight on the GIANT Pressure Washer PUMP P313.
Description: LANDA – GIANT Pressure Washer PUMP P313 RIGHT-HAND SHAFT – 8.702-356.0
The GIANT Pressure Washer PUMP P313 Features:
- Volume ………………………………………………… Up to 3.8 GPM ………(14.4 LPM)
- Discharge Pressure P313 (Continuous) ……… Up to 3200 PSI ……… (220 bar)
- Discharge Pressure P313 (Intermittent) ……… Up to 3500 PSI ……………(240 bar)
- Discharge Pressure P314 (Continuous) ……… Up to 3500 PSI ……… (240 bar)
- Discharge Pressure P314 (Intermittent) ……… Up to 4000 PSI ……… (275 bar)
- Inlet Pressure ………………………………………………………………………. Positive Inlet Pressure Required
- Stroke ………………………………………………….. 0.55”……………………14.1mm
- RPM…………………………………………………………………………………..Up to 3450 RPM
- Plunger Diameter …………………………………… 0.47”……………………12mm
- Temperature of Pumped Fluids ………………… Up to 160 oF ………….(71 oC)
- Inlet Ports …………………………………………………………………………… (2) 1/2″ BSP
- Discharge Ports …………………………………………………………………… (2) 3/8″ BSP
- Shaft Rotation ……………………………………….. Top of pulley towards manifold
- Crankshaft Diameter ……………………………………………………………..24mm
- Key Width …………………………………………………………………………..8mm
- Shaft Mounting ……………………………………………………………………. Either side2
- Weight …………………………………………………. 16 lbs. …………………. (7.26 kg)
- Crankcase Oil Capacity ………………………….. 14.2 fl.oz. …………….. (0.42 liters)
- Extended Crankcase Oil Capacity …………….. 17 fl. oz. ………………. (0.5 liters)
GIANT Pressure Washer PUMP P313
The repair Manual for the Giant Pressure Washer Pump P313 can be found by clicking here.
GIANT Pressure Washer PUMP P313
INSTALLATION INSTRUCTIONS FOR THE GIANT Pressure Washer PUMP P313
Installation of the Giant Industries, Inc., pump is not a complicated procedure, but there are some basic steps common to all pumps. The following information is to be considered as a general outline for installation. If you have unique requirements, please contact Giant Industries, Inc. or your local distributor for assistance.
1. The P313 pump should be installed flat on a base to a maximum of a 15 degree angle of inclination to ensure optimum lubrication.
2. The inlet to the P313 pump should be sized for the flow rate of the pump with no unnecessary restrictions that can cause cavitation. Teflon tape should be used to seal all joints. If pumps are to be operated at temperatures in excess of 1600 F, it is important to insure a positive head to the pump to prevent cavitation.
3. The discharge plumbing from the pump should be properly sized to the flow rate to prevent line pressure loss to the work area. It is essential to provide a safety bypass valve between the pump and the work area to protect the pump from pressure spikes in the event of a blockage or the use of a shut-off gun.
4. Use of a dampener is necessary to minimize pulsation at drive elements, plumbing, connections, and other system areas. The use of a dampener with Giant Industries, Inc. pumps is optional, although recommended by Giant Industries, Inc. to further reduce system pulsation. Dampeners can also reduce the severity of pressure spikes that occur in systems using a shut-off gun. A dampener must be positioned downstream from the unloader.
5. When viewed from the side of the P313 pump, crankshaft rotation is clockwise on pumps with left handed shafts and counterclockwise on pumps with right handed shafts. Reverse rotation may be safely achieved by following a few guidelines available upon request from Giant Industries, Inc. Required horsepower for system operation can be obtained from the charts on pages 3-7 and 10.
6. Before beginning operation of your pumping system, remember: Check that the crankcase and seal areas have been properly lubricated per recommended schedules. Do not run the P313 pump dry for extended periods of time. Cavitation will result in severe damage. Always remember to check that all plumbing valves are open and that pumped media can flow freely to the inlet of the P313 pump.
List Price: $1,008.31
Our Price: $924.01 
You save $84.30!
Availability:: available for order
Product Code: LAN-8.702-356.0
PRICE SUBJECT TO CHANGE. PRICE VALID ON THE GIANT PRESSURE WASHER PUMP P313 – 1/09/2012
