A Spotlight on the XMA4G20N Pressure Washer Pump from Annovi Reverberi.
XMA4G20N Pressure Washer Pump from Annovi Reverberi
The Technical Specifications of the XMA4G20N Pressure Washer Pump:
- Max GPM………………4
- Max PSI………………….2000
- Power EBHP……………5.5
- Bore Dia. mm…………………….18
- Stroke mm……………….13.2
- Weight Lbs………………………..14
- Max Temp……………….140°
- Oil Capacity………………………14.5oz
- Inlet Thread ……………1/2”F
- Discharge Thread……………….3/8”F
The Features on this XMA4G20N Pressure Washer Pump:
- This XMA4G20N Pressure Washer Pump has Forged Brass: Strength and no porosity equals long life. Higher hydrostatic pressures, safety and performance.
- Inlet and Discharge Ports: Heavy bosses for added strength.
- Offset Discharge Ports: High efficiency, smooth flow.
- The Bolts on the XMA4G20N Pressure Washer Pump: Eight bolts, 6mm, grade 12.9.
- Ultra Form Cages: Durability, strength and long life.
- Poppets, Seat and Spring: 303 and 400 series stainless steel.
- Valve Caps of this XMA4G20N Pressure Washer Pump: Machined brass – greater strength.
- High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
- Low Pressure Seals: “U” cup double lip Buna-N, good positive seal.
- Support Guides: Machined brass, two-piece construction to assure proper plunger alignment and to maximize packing and seal life.
- The Plungers on the XMA4G20N Pressure Washer Pump: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
- Over sized for maximum life and load disbursement, needle bearing on the drive side and ball on the non-drive side. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
- Crankcase: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
- Rear Cover: precision die-cast, O-ring sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen).
- Stainless steel construction for strength (no plating to scrape off). O-ring plunger sealing system.
- Rod Pins: Precision ground and hardened steel, over sized for load disbursement.
- Connecting Rods: One-piece special alloy aluminum based, over sized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
- The XMA4G20N Pressure Washer Pump has a Crankshaft: Forged, precision ground and hardened for extremely long life and durability.
- Oil Seals and O-rings: All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
- Oil Capacity of the XMA4G20N Pressure Washer Pump: 14.5 oz., refer to parts breakdown.
- Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
- Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
- Hot Water: High temperature kits are available on the XMA4G20N Pressure Washer Pump to 180º F. Refer to breakdown
- Wet End Repair: Very simple no special tools are required.
- Mounting Bolt Pattern: Same on the top and bottom of the crankcase for simple drive side change.
- Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.
XMA4G20N AR (Annovi Reverberi) Pump 4 GPM @ 2000 PSI. AR pumps are a combination of exceptional degree of technology and innovation, quality and reliability worthy of a leading brand on the market. The wide range includes many models which vary in terms of pressure, deliver, power and technical characteristics, to satisfy widely different market demands.
Additional Info on the XMA4G20N Pressure Washer Pump:
- Items NOT INCLUDED with your XMA4G20N pump that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!
- The PUMP GUARD of the XMA4G20N will ‘dump’ any water above 145 degrees F. before it reaches your pump (saving you the trouble of rebuilding your pump)
- PRESSURE REGULATOR / UNLOADER – if we list one to the right of the pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.
- The INLET WATER FILTER will catch most small debris before it enters your pump
- The EZ-START VALVE on this XMA4G20N will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer
- The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your pump!
- PUMP OIL, you can never have enough on hand! Many pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.
List Price: $618.72
You save $230.83!
- PSI: 2000
- GPM: 4
Availability:: available for order
Product Code: XMA4G20N
Price on the XMA4G20N subject to change.
