SJV2.5G27D-F7 AR Annovi Reverberi Pressure Washer Pump

Spotlight on the SJV2.5G27D-F7 AR Annovi Reverberi Pressure Washer Pump.

Technical Specifications of this SJV2.5G27D-F7 Pressure Washer Pump:

SJV2.5G27D-F7 AR Annovi Reverberi Pressure Washer Pump

Features of this SJV2.5G27D-F7 Pressure Washer Pump:

• – Forged Brass: Strength and no porosity – long life. Higher hydrostatic pressures – safety.
• – Unloader: Built in to optimize performance while reducing setup time. Integral trap pressure, fixed or adjustable chemical injector.
• – Bolts: Three bolts, 10mm, grade 8.8.
• – Ultra Form Cages: Durable, strong, and long life. Unique inlet valve configuration: the valve cage incorporates the high pressure packing head ring.
• – Poppets, Seat and Spring: 303 and 400 series stainless steel.
• – Valve Caps: Machined brass for greater strength.
• – High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load. Continuously lubricating for extended life, self lubricating packing/Plunger guide support ring.
• – Low-Pressure Seals: “U” cup double lip Buna-N for a good positive seat.
• – Support and Guides: Machined brass, 1-piece construction to assure proper plunger alignment, maximize packing and seal life.
• – Plungers: Coated ceramic stainless steel, strong and durable. The pump includes a plunger shoe to distribute the additional plunger load.
• Bearings: Angular contact ball bearing stabilizes the crankshaft and one thrust needle bearing absorbs the plunger load and assures long radial plate life. All of the thrust plates are made of heat treated hardened steel for extended life.
• Crankcase: Precision die-cast, large cooling fins and anodized for maximum heat dissipation. Sight glass, fill and drain plugs.
• Rear Cover: Precision die-cast, O-ring sealed. The housing retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer.
• Crankshaft/Wobble Plate: Precision die-cast to assure proper stroke, duration and alignment.
• Oil Seals and O-rings: All are constructed of Buna-N rubber. The oil seals have stainless steel garder springs to assure constant tension on the sealing surface.
• Oil Capacity: 4.5 oz.
• Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
• Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
• Wet End Repair: Very simple no special tools required.
• Mounting Flanges: Gasoline SAE J609a flange. Refer to breakdown.
• Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.

The AR SJV2.5G27D-F7 pump is designed for medium duty loads. It spins at 3400 RPM in a direct drive system coupled with a gasoline engine, the matching flange provides convenient connections to most 3/4” shaft 3.5 – 6.5 HP engines. Optional vertical and horizontal setups. Precision die-cast crankcase with large cooling fins for maximum heat dissipation. Seals and V-Packings designed to continuously lubricate for extended life.  This SJV2.5G27D-F7 pump has a Built-in unloader to optimize performance while reducing setup time. Integral trap pressure with fixed or adjustable chemical injector.

SJV2.5G27D-F7

Recommended Accessories / Additional Info:

• NOT INCLUDED with your SJV2.5G27D-F7 pump that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!
• The PUMP GUARD will ‘dump’ any water above 145 degrees F. before it reaches your pump (saving you the trouble of rebuilding your pump)
• PRESSURE REGULATOR / UNLOADER – if we list one to the right of the SJV2.5G27D-F7 pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.
• The INLET WATER FILTER will catch most small debris before it enters your pump
• The EZ-START VALVE will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer
• The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your SJV2.5G27D-F7 pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your pump!
• PUMP OIL, you can never have enough on hand! Many pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.

SHIPPING: Item Ships in 1 to 7 Days

Availability:: In Stock
Product Code: ARWP-RTR-SJV2.5G27D-F7
price subject to change  on the SJV2.5G27D-F7