SXMA3G35E-F17 AR Annovi Reverberi Pressure Washer Pump
SXMA3G35E-F17 AR Annovi Reverberi Pressure Washer Pump
SXMA3G35E-F17 AR (Annovi Reverberi) Pump 3 GPM @ 3500 PSI.
SXMA3G35E-F17 Plunger Pumps are designed for high-pressure industrial washing applications. They are constructed of die-cast bodies and feature a forged brass heads with a bayonet style sight glass in the rear and side covers. Internal components include special thick solid ceramic plungers for long life and durability. Precision cast cooling fins are anodized for maximum heat dissipation. Over sized premium SKF tapered roller bearings and the precision die-cast supports on the SXMA3G35E-F17 assure proper shaft alignment and maximum life. Valve cages of Ultra-Form provide positive seating and extended life, especially designed for high pressure applications. Two-piece connecting rods are a special alloy aluminum-based material over sized for maximum strength and load disbursement. Spinning at 1750 RPM, this SXMA3G35E-F17 pump was designed to deliver 3GPM at 3500 PSI.
The SXMA3G35E-F17 AR Annovi Reverberi Pressure Washer Pump has the following specifications:
- Max Flow (in GPM): 3.0
- Max Flow (in L/Min): 11.4
- Max Pressure (in PSI): 3500
- Max Bar: 240
- Power EBHP: 7.0
- Bore Dia: 15mm
- Stroke: 13.2mm
- Crankshaft ID Stamp: 3
- Pump Speed (in RPM): 1750
- Shaft Diameter: 1-1/8″ hollow
The SXMA3G35E-F17 AR Annovi Reverberi Pressure Washer Pump has the following Features:
- Manifold:
- – Forged Brass: Strength and no porosity equals long life. Higher hydrostatic pressures, safety and performance.
- – Inlet and Discharge Ports: Heavy bosses for added strength.
- – Offset Discharge Ports: High efficiency, smooth flow.
- – Bolts: Eight bolts, 6mm, grade 12.9.
- SXMA3G35E-F17 Valves:
- – Ultra Form Cages: Durability, strength and long life.
- – Poppets, Seat and Spring: 303 and 400 series stainless steel.
- – Valve Caps of the SXMA3G35E-F17: Machined brass – greater strength.
- Packing and Plungers:
- – High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
- – Low Pressure Seals: “U” cup double lip Buna-N, good positive seal.
- – Support Guides: Machined brass, two-piece construction to assure proper plunger alignment and to maximize packing and seal life.
- – Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
- Bearings: Over sized for maximum life and load disbursement, needle bearing on the drive side and ball on the non-drive side. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
- Crankcase on the SXMA3G35E-F17: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
- Rear Cover: precision die-cast, O-ring sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen).
- Plunger Rods of the SXMA3G35E-F17: Stainless steel construction for strength (no plating to scrape off). O-ring plunger sealing system.
- Rod Pins: Precision ground and hardened steel, over sized for load disbursement.
- Connecting Rods: One-piece special alloy aluminum based, over sized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
- Crankshaft: Forged, precision ground and hardened for extremely long life and durability.
- Oil Seals and O-rings: All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
- Oil Capacity: 14.5 oz., refer to parts breakdown.
- Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
- Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
- Hot Water: High temperature kits are available to 180º F. Refer to breakdown
- Wet End Repair: Very simple no special tools are required.
- Mounting Bolt Pattern: Same on the top and bottom of the crankcase for simple drive side change.
- Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.
List Price: $768.30
Our Price: $479.97 Click to order the SXMA3G35E-F17 AR Annovi Reverberi Pressure Washer Pump
You save $288.33!
Availability:: available for order
Product Code: SXMA3G35E-F17
Price Subject to change on the SXMA3G35E-F17 Pressure washer pump from Annovi Reverberi.
