Oct 05 2011

LANDA SLX Series Pressure Washer

SLX – The Only Portable Hot Water Pressure Washer that Delivers 200°F Cleaning at up to 10 GPM!

•Dual-Gun Ready
•Powered by Gasoline
•Diesel; Diesel-Heated
•Belt-Drive Landa Pump with 7-Year Warranty
•3/4″ Schedule 80 Coil

LANDA SLX Series Pressure Washer

LANDA SLX Series Pressure Washer

The LANDA SLX Series Pressure Washer has the following:

•Pre-plumbed with 3-Way Valve to bypass float tank when drawing water directly from an auxiliary tank.
•Extra-large Heating Coil made of cold-rolled, 3/4″ Schedule 80 steel pipe with 5-year warranty; features Stainless Steel Top Wrap; unique lift-out design for easy and quick Coil Access.
•Rugged 2″ x 4″ x 1/8″ thick box steel frame, with compact footprint, shields key components; further protected by weather-resistant Epoxy Powder Coat finish; Power Platform is vibration isolated to minimize frame stress.
•Water-resistant, metal Control Panel has adjustable thermostat, combination hour meter and tachometer, volt meter, burner switch and tri-lingual operating instructions for added safety.
•Industrial-duty tri-plunger Landa Pump designed to run at low RPM for long life, 7-year warranty, with single-rail true-track Pulley Adjustment.
•Adjustable Detergent and Steam Valves provide precise metering of soap and on-demand wet-steam cleaning.
•Illustrated Warning Labels universally understandable for liability protection.
•Gasoline-powered Vanguard and Honda Engines, or watercooled, 16‑27 hp diesel Kohler Engine all come with keyed electric starter for easy start-up and protection against unauthorized use; polyurethane Battery Box with vibration isolators protects and firmly secures battery (battery not included).
•30‑gallon diesel and 16‑gallon gasoline Fuel Tanks (15‑gallon diesel and 10‑gallon gasoline on SLT) provide hours of uninterrupted operation; with elevated fuel lines to  avoid suctioning of settled debris.
•50 ft. of double-wire braid High Pressure Hose rated for up to 6000 PSI and featuring a 24-inch safety hose guard for operator burst protection.
•Efficient 2,000-Watt Generator produces reliable power for burner.
•High-efficiency Burner, with dual rings for “dialing in” air flow, has a Fuel- Water Separator for fuel pump protection.
•Many Safety Features, including a rupture disk, thermal pump protector, flow switch, unloader valve, and safety lock on the trigger gun.
•Corrosion-resistant Float Tank has stainless steel inlet filter and 3/4″ float valve with anti-siphon backflow protection; also allows for introduction of detergents in high pressure mode.
•Insulated, fatigue-free Trigger Gun, with swivel crimp fitting for a tangle-free hose. Stainless steel, dual-lance Variable Pressure Wand features an ergonomic design and easy adjusting of the water pressure while cleaning.

WHY CHOOSE LANDA’s SLX or SLT

When it comes to heavy-duty grease or grime, most high-volume, hot water pressure washers fall short with their 150°F water. Landa’s SLX, and smaller SLT, are the first power washers ever designed to deliver a high-volume flow at 200°F water, hot enough to melt the toughest of oily messes. The SLX delivers enough hot water flow—up to 9.5 GPM—that you can operate two spray guns at the same time!

Other benefits include:

QUALITY: Packed with Landa quality throughout, the SLX and SLT feature a top-of-the-line, belt-drive Landa Pump with 7-year warranty and low RPM for extended life, as well as a giant Schedule 80 heating coil, made of up to 300 ft. of 3/4‑inch steel pipe with 5-year warranty.

DURABILITY: Extraordinarily rugged frame is made of 2-by-4-inch box steel with an all-metal power platform cushioned by 10 vibration isolators to minimize frame stress.

EFFICIENT: The SLX-SLT is heated by a high-efficiency Beckett burner with dual rings for dial-in air flow. The 3/4″ heating coil is amazingly efficient due to its unique “breathing” design so it heats quieter while promoting optimum heat exchange.

FUNCTIONAL: The SLX-SLT has a remarkably compact footprint, is certified to UL-1776 safety standards, is pre-plumbed for drawing water from an auxiliary tank, has six forklift guides for portability and the control panel is ideally positioned for curb access when the unit is mounted on a trailer or truck bed.

SLX  Specifications
Engine Gas Diesel
Model No. GPM PSI Engine CCs(HP) Fuel Tank Tank Pump RPM BTU’s L x W x H SHIP WT.
SLX10-25324E 9.5 2500 Honda 670(24) Gasoline 16 30 1560 887,000 65″ x 36″ x 58″ 2020 lbs.
SLX10-25824E 9.5 2500 Kohler 1028(27) Diesel N/A 40 1470 887,000 65″ x 36″ x 58″ 2160 lbs.
SLT5-30224E 5.2 3000 Vanguard 479(16) Gasoline 10 15 1295 485,000 55″ x 32″ x 51″ 1210 lbs.
SLT6-32324E 5.9 3200 Honda 614(20) Gasoline 10 15 1570 550,000 55″ x 32″ x 51″ 1220 lbs.
SLT8-30324E 7.8 3000 Honda 670(24) Gasoline 10 15 1470 728,000 55″ x 32″ x 51″ 1230 lbs.
SLT5-30824E 4.4 3000 Kohler 686(16) Diesel N/A 26 1295 410,000 62″ x 32″ x 53.5″ 1715 lbs.
SLT6-32824E 5.9 3200 Kohler 1028(27) Diesel N/A 26 1470 588,000 62″ x 32″ x 53.5″ 1785 lbs.
SLT8-30824E 7.8 3000 Kohler 1028(27) Diesel N/A 26 1560 728,000 62″ x 32″ x 53.5″ 1850 lbs.

Note: Landa is constantly improving and updating its products. Consequently, pictures, features, and specifications  may differ slightly from current models. Flow rates and pressure ratings may vary due to variances allowed by manufacturers of their machine components. Landa product performance is certified by the Cleaning Equipment Trade Association (CETA) to be within 5% of listed specifications.

Permanent link to this article: https://etscompany.com/wordpress/2011/10/05/landa-slx-series-pressure-washer/

Oct 05 2011

PGHW Series, Gasoline-Powered/Diesel/Oil Heated Pressure Washer

For more than a decade, the PGHW has been LANDA’s most popular gasoline-powered, hot water pressure washer. The PGHW combines the versatility of a compact size yet the ruggedness and cleaning power of a full-skid pressure washer.
Five PGHW models deliver cleaning power of up to 5000 PSI with a flow rate of up to 5 GPM. The PGHW is packed with power by reliable Honda, Vanguard or Kawasaki electric-start engines, the PGHW models feature top-of-the-line, oil-bath, tri-plunger, belt-drive and a Land pumps with a 7-year warranty. The heating coil is made of 1/2-inch Schedule 80 cold-rolled pipe (Schedule 160 on 5000 PSI model) with a stainless steel outer top wrap. The sturdy steel frame gets all-weather protection from an epoxy powder coat finish. A 2,000 watt generator provides power for the burner as well as a 120V outlet for low-wattage applications.
LANDA PGHW Pressure Washer

LANDA PGHW Pressure Washer

The LANDA PGHW Pressure Washer has the following Specifications:

•Up to 5 GPM, 5,000 PSI
•Honda, Vanguard or Kawasaki Engines
•LANDA Belt-Drive Pump with 7-Year Warranty
•2,000 Watt Generator
•Rugged tri-plunger High-Pressure Landa Pump with forged brass head and 7‑year warranty, is connected to the engine by a belt-drive assembly that features cast-iron bushing Pulleys and two notched “V” cogged belts, which provide a cooler operation and longer life; also single-rail truetrack Pulley Adjustment makes it easy to alter the belt tension.
•Trailer-ready with pre-drilled Trailer Mounting Brackets and pre-plumbed with 3‑Way Valve to bypass float tank when drawing water directly from an auxiliary tank. (5000 PSI model not trailer ready)
•High-efficiency Burner is mounted on the end for ease of servicing and adjustments.
•Power Platform is mounted on vibration isolators to extend the life of the key components.
•2,000 Watt Generator produces reliable power for burner.
•Heavy-duty Fuel-Water Separator has replaceable element for removing water that can damage burner fuel pump.
•Rupture Disk and Thermal Pump Protector protect against excessive heat or pressure.
•Rugged, 11/2-inch square tube Open-Air Frame with Forklift Guides allows easy access and serviceability and is protected by an all-weather resistant Epoxy Powder Coat Finish.
•Super-duty Horizontal Heating Coil, made of cold-rolled, Schedule 80 steel pipe has a 5‑year warranty and is surrounded by an aluminized steel inner wrap and stainless steel top wrap. (5000 PSI model has Schedule 160 coil and all stainless outer wrap)
•Durable polyurethane Battery Box protects battery and is easy to access.
•Color-coded, polyethylene Fuel Tanks for gasoline (5 gal.) and diesel (10 gal.) are translucent for monitoring fuel level. Diesel tank has Low-Fuel Shutoff to protect the burner fuel pump. Both have elevated fuel lines to prevent debris in fuel from causing damage. (gasoline tank is 10 gal. on 5000 PSI model and 1.5 gal. on 13 HP model)
•Industrial-duty Gasoline-Powered Honda, Vanguard or Kawasaki engine with overhead valves; all have keyed Electric Start.
•Insulated, spring-loaded Trigger Gun with inline Detergent Injection and insulated, stainless steel, dual-lance Variable Pressure Wand make it easy to switch between wash and rinse modes. (5000 PSI model has straight thru wand)
•Helpful Tri-Lingual Labels with operating instructions in English, Spanish and French for owner and operator protection.
•Many Safety Features, including redundant devices such as a rupture disk, thermal pump protector and high-temperature shut down to guard against any build up of excessive pressures or heat.
•Conveniently placed Control Panel can be relocated to front of machine and features Burner On/Off Switch, Low-Fuel Light for fuel pump protection, Adjustable Thermostat to control temperature, and Hour/Tach Meter to indicate engine speed and total operating time.
•Adjustable Detergent Valve for precise high-pressure metering of soap. Optional Steam Valve provides ondemand wet-steam cleaning. (steam valve standard on 5000 PSI model)
•Rust-free Float Tank with stainless steel inlet filter provides backflow protection and inlet Detergent Injection for applying soap while washing in high pressure mode.
•50 ft. of 3/8″, double-wire braid Landa Tuff-Skin Hose featuring a 24-inch Hose Guard for burst protection.
•Four Quick-Couple Nozzles are made of hardened stainless steel and are mounted for ready access.

WHY CHOOSE LANDA’s PGHW

For more than a decade, the PGHW has been Landa’s most popular gasoline powered, hot water pressure washer. It combines the versatility of a compact size yet the ruggedness and cleaning power of a full-skid pressure washer. The five PGHW models deliver cleaning power of up to 5000 PSI with a flow rate of up to 5 GPM. The PGHW is packed with:

QUALITY: Powered by reliable Honda, Vanguard or Kawasaki electric-start engines, the PGHW models feature top-of-the-line, oil-bath, tri-plunger, belt-drive  Landa pumps with 7-year warranty. The heating coil is made of 1/2-inch Schedule 80 cold-rolled pipe (Schedule 160 on 5000 PSI model) with a stainless steel outer top wrap. The sturdy steel frame gets all-weather protection from an epoxy powder coat finish.
VERSATILITY: A 2,000 watt generator provides power for the burner as well as a 120V outlet for low-wattage applications. The PGHW has forklift guides for transporting, brackets for mounting on a trailer, and an optional wheel kit. The large fuel tanks provide hours of continuous cleaning and the float tank, with pre-plumbed 3-way bypass valve, allows high-pressure soap application.

SAFETY: As with all Landa models, the PGHW comes certified to the rigid UL-1776 safety standards, featuring: 24-inch hose guard for burst protection; thermal pump protector; high-temperature shut down to prevent super-high heat build up; and rupture disk to vent any build up of excessive pressure in the heating coil.

PGHW Specifications
Model No. Part No. GPM PSI Engine CCs(HP) Start Pump RPM BTU’s L x W x H SHIP WT.
PGHW4-30324E 1.110-048.0 3.5 3000 Honda 389(13) Electric 1125 372,000 48″ x 32″ x 44″ 725 lbs.
PGHW5-30224E 1.110-046.0 4.8 3000 Vanguard 479(16) Electric 1375 470,000 48″ x 32″ x 44″ 700 lbs.
PGHW5-35324E 1.110-045.0 4.7 3500 Honda 614(20) Electric 1360 385,000 48″ x 32″ x 44″ 750 lbs.
PGHW4-40324E 1.110-047.0 4.0 4000 Honda 614(20) Electric 1425 372,000 48″ x 32″ x 44″ 735 lbs.
PGHW5-50524E 1.110-512.0 5.0 5000 Kawasaki 745(27) Electric 1585 470,000 48″ x 39″ x 42″ 1285 lbs.

Note: LANDA is  constantly improving and updating their products. Consequently, pictures, features, and specifications  may differ slightly from current models. Flow rates and pressure ratings may vary due to variances allowed by manufacturers of LANDA’s machine components. LANDA attempts  to keep their machine performance within ±5% of listed specifications.

OPTIONS:
Part No. Description
8.916-588.0 Stainless Steel Bottom Wrap (factory installed)
8.916-585.0 Steam Valve Kit
8.904-525.0 Wheel Kit (not for 5000 PSI model)
8.915-496.0 360° Pivot Hose Reel Kit (100 ft capacity)
8.903-522.0 Non-Pivot Hose Reel Mounting Kit
8.711-858.0 175 ft Cox Hose Reel
9.804-067.0 100 ft E-Zee Hose Reel

Permanent link to this article: https://etscompany.com/wordpress/2011/10/05/pghw-series-gasoline-powereddieseloil-heated-pressure-washer/

Oct 04 2011

General Pump Stainless Steel Check Valve YCV38FSS

General Pump Stainless Steel Check Valve YCV38FSS  – 3/8″F-NPT

Click here for the General Pump Stainless Steel Check Valve YCV38FSS parts list.

General Pump Stainless Steel Ckeck Valve YCV38FSS

General Pump Stainless Steel Ckeck Valve YCV38FSS

The General Pump Stainless Steel Check Valve YCV38FSS Features:

  • General Pump Stainless Steel Check Valve
  • 10.5 gpm
  • Rated pressure: 5800 psi, max. 6500psi
  • 3/8″ inlet

List Price: $57.10
Our Price: $43.94 
You save $13.16!
Availability:: available for order
Product Code: YCV38FSS
Price subject to change – Valid 10/4/2011

Permanent link to this article: https://etscompany.com/wordpress/2011/10/04/general-pump-stainless-steel-check-valve-ycv38fss/

Oct 04 2011

COMET PRESSURE WASHER PUMP AXD 2020 E – 6501.0010.00

The COMET PUMP AXD 2020 E PART NO. 6501.0010.00,  has 1.9 GPM @ 2000 PSI @ 3400 RPM.  To see product spec sheet for detailed specifications, repair kits and replacement parts for the COMET PRESSURE WASHER PUMP AXD 2020 E – 6501.0010.00. Click here.

The COMET PRESSURE WASHER PUMP AXD 2020 E – 6501.0010.00 Features:

  • 3400 RPM – 5/8″ Hollow Shaft
  • 3/4″ FGH Inlet – 3/8″ MPT Outlet
  • Built-in Uniflow Unloader and Chemical Injector
  • Ceramic Plungers
  • Built-in Garden Hose Adapter
  • Industrial Duty Construction for Extended Life
  • Optional Built-in Thermal Protector & Pressure Relief
  • Stainless Steel Check Valves
  • Forged Brass Manifold
  • Patent Registered Ball Bearing Design
  • NEMA 56C Electric Motor Flange
Comet Pressure Washer Pump AXD 2020 E 6501.0010.00

Comet Pressure Washer Pump AXD 2020 E 6501.0010.00

Comet Pressure Washer Pump AXD 2020 E 6501.0010.00 exploded view

Comet Pressure Washer Pump AXD 2020 E 6501.0010.00 exploded view

The COMET PRESSURE WASHER PUMP AXD 2020 E – 6501.0010.00 has the following specifications:

  • Maximum Volume 1.9 gpm
  • Max. Discharge Pressure 2000 psi
  • Maximum Pump Speed 3400 rpm
  • Inlet Port Thread 3/4 FGH
  • Discharge Port Thread 3/8 MPT
  • Shaft Diameter 5/8 Hollow
  • Weight 12.0 lbs.

List Price: $580.00
Our Price: $293.64 
You save $286.36!
Availability:: available for order
Product Code: 6501.0010.00
Comet Pressure Washer Pump
PRICE SUBJECT TO CHANGE – VALID AS OF 10/4/2011

Permanent link to this article: https://etscompany.com/wordpress/2011/10/04/comet-pressure-washer-pump-axd-2020-e-6501-0010-00/

Oct 03 2011

AR Annovi Reverberi Pressure Washer Pump – RMW2G24

The AR Annovi Reverberi Pressure Washer Pump – RMW2G24 is the  Vertical Shaft Replacement Pump!
Inlet & Outlet come out in the FRONT of the engine (spark plug end).  Most pressure washer pumps are only designed to last for approximately 50 hours of use. This Annovi Reverberi Pump RMW2G24 is designed to last for 300 + hours of use.

IT’S IMPORTANT TO NOTE:
Depending on your Pressure Washer model, you may need to get three new mounting bolts to mount the Annovi Reverberi Pump RMW2G24 to the engine. In this case, your local hardware store will carry these bolts. There are too many different Pressure Washer models and bolt size combinations so we cannot provide new bolts for the replacement pump.
Below are the most common bolt sizes needed to mount your new replacement Annovi Reverberi Pressure Washer Pump – RMW2G24 to the engine:
– 5/16″ 18 x 2 1/2″ (Qty. 2)
– 5/16″ 18 x 3 1/2″ (Qty. 1)

The Annovi Reverberi Pressure Washer Pump – RMW2G24 Features:

  • 7/8″ hollow shaft
  • operates at 3400 RPM
  • max PSI of 2400
  • Manifold is made from precision die cast aluminum with a special anti-corrosion finish.
Annovi Reverberi Pressure Washer Pump - RMW2G24

Annovi Reverberi Pressure Washer Pump - RMW2G24

The Annovi Reverberi Pressure Washer Pump – RMW2G24 has the following specifications:

  • Max Flow (in GPM): 2.0
  • Max Flow (in L/Min): 7.6
  • Max Pressure (in PSI): 2400
  • Max Bar: 166
  • Power EBHP: 3.2
  • Bore Dia: 12mm
  • Stroke: 8.3mm
  • Crankshaft ID Stamp: 5
  • Pump Speed (in RPM): 3400
  • Shaft Diameter: 7/8″ hollow

List Price: $243.26
Our Price: $156.74
You save $86.52!

Availability:: available for order
Product Code: RMW2G24
Annovi Reverberi Pressure Washer Pump

Permanent link to this article: https://etscompany.com/wordpress/2011/10/03/ar-annovi-reverberi-pressure-washer-pump-rmw2g24/

Oct 03 2011

Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH

Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH

This Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH has the following Frame: Powder coated steel frame, handle and tank · Heavy-duty tires for easy mobility · Front foot brace · Rugged steel body

The Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH Burners: Stainless-steel combustion chamber · Direct spark ignition

These Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH Motors have: Heavy-duty, high quality cast aluminum electric motor

The Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH has the following Components: Safety switch prevents overheating · Thermostatically controlled · Suitable for air ducting · Easy to operate controls · High capacity fuel tank · Electronic flame control · Automatic ignition · Water resistant control box · Automatic fuel shut-off · High thermal efficiency · Control panel with thermostat plug, reset push button and safety air pressure switch · High pressure fuel pump · Vacuum sensor helps prevent heater lock out · Heated fuel filter for more reliable starts in subzero temperatures

The Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH will Function on: Kerosene or No. 1 and No. 2 fuel oil.

The Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH is for use on construction sites and applications where the heat will be ducted into a building.

The MH-0125-0MIH Specifications subject to change without notice. Use in accordance with any and all state or local codes, regulations, and/or ordinances.

Please see heater “Owner’s Manual” included with each MH-0125-0MIH for a complete list of important safety information.

Important Notes about the MH-0125-0MIH:
· Not for use in residential living areas or inadequately ventilated areas.
· Proper ventilation required during operation.
· Must be plugged into an approved standard electrical outlet for operation.

View Product Information Sheet for Mi-T-M Portable Heater Kerosene Indirect Ductable – MH-0125-0MIH

Mi-T-M Portable Heater Kerosene Indirect Ductable MH-0125-0MIH

Mi-T-M Portable Heater Kerosene Indirect Ductable MH-0125-0MIH

The MH-0125-0MIH has the following technical specifications:

  • Heat Output 125,000 BTU
  • Temperature Rise 130°F
  • Max. Output Temperature 240°F
  • Heated Air Output 1,180 CFM
  • Power Consumption 460 watts
  • AC Power 115 Volts/60Hz/1Ø/7.0 Amp
  • Fan Static Pressure 0.7-inch WC
  • Fuel Consumption 0.9 gal./hr.
  • Fuel Tank Capacity 13.5 gallons
  • Max. Operating Hours 15 hours
  • Duct Size (LxDiameter) 25 ft.x12in.
  • Net Weight 154 lbs.
  • Shipping Weight 162 lbs.
  • Length 54.8 in.
  • Width 27.6 in.
  • Height 32.7 in.

List Price: $2,670.00
Our Price: $2,269.50 
You save $400.50!
Availability:: available for order
Product Code: MH-0125-0MIH
Mi-T-M Portable Heater

Permanent link to this article: https://etscompany.com/wordpress/2011/10/03/mi-t-m-portable-heater-kerosene-indirect-ductable-mh-0125-0mih/

Sep 30 2011

Mi-T-M Portable Heater Propane Directional – MH-0175-0MDH

Mi-T-M Portable Heater Propane Directional – MH-0175-0MDH

The MH-0175-0MDH Outer Casing/Design: Rugged design · Durable powder coated outer casing and side lifting handles · Lifting handles for easy loading and unloading · The unit is naturally balance to lift easily with handles · Two 10-inch solid rubber tires for mobility and easy placement

This MH-0175-0MDH has the following Components: Independent fan and burner controls for simple operation · Thermostat control with 20-foot cord allows for a consistent, comfortable environment and use in remote locations · 15-foot hose and regulator assembly · Air flow safety devices · Totally enclosed frame · Fully enclosed electronics · Electronic ignition · Operates as both a fresh air circulator or a heater at the touch of a switch · Super quiet, super efficient · Easy to set-up · Numerous duct options available · Direct spark ignition

The Mi-T-M Portable Heater Propane Directional – MH-0175-0MDH is intended for use in tent and party applications or construction sites.

Specifications on the Mi-T-M Portable Heater Propane Directional – MH-0175-0MDH subject to change without notice. Use in accordance with any and all state or local codes, regulations, and/or ordinances.

Please see heater “Owner’s Manual” included with each heater for a complete list of important safety information.

Important Notes:
· Not for use in residential living areas or inadequately ventilated areas.
· Proper ventilation required during operation.
· Extremely hot during operation. Keep children, animals and all combustible objects away from heater.

View Product Information Sheet for Mi-T-M Portable Heater Propane Directional – MH-0175-0MDH

Mi-T-M Portable Heater Propane Directional MH-0175-0MDH

Mi-T-M Portable Heater Propane Directional MH-0175-0MDH

The Mi-T-M Portable Heater Propane Directional MH-0175-0MDH has the following specifications:

  • Heat Output 175,000 BTU
  • Type Propane
  • Heated Air Output 1,200 CFM
  • Fuel Consumption 8.75 lbs./hr.
  • Inlet Gas Pressure 11-inch WC
  • Temperature Rise (above ambient) 140°F
  • Suggested Tank Size 100 lbs.
  • Electrical Requirements 115 Volts/60Hz/1Ø
  • Amps (Starting/Cont.) 8.4 / 3.6 Amps
  • Net Weight 164 lbs.
  • Shipping Weight 193 lbs.
  • Length 30.62 in.
  • Width 18.25 in.
  • Height 31.12 in.

List Price: $2,465.00
Our Price: $2,095.25 
You save $369.75
Availability:: available for order
Product Code: MH-0175-0MDH
Mi-T-M Portable Heater

Permanent link to this article: https://etscompany.com/wordpress/2011/09/30/mi-t-m-portable-heater-propane-directional-mh-0175-0mdh/

Sep 30 2011

CAT Pump 8058 Direct Drive Gearbox

CAT Pump 8058 Direct Drive Gearbox Helical -1-1/8″ Shaft, Gearbox Pump: 51G118, 58G118 Used on Models 51 and 58 Pump.

The CAT Pump 8058 Direct Drive Gearbox Features:

  • Polished solid ceramic plungers last long and resist abrasion.
  • Triplex plunger design providing low pulsation and quiet operation.
  • Internally lubricated and cooled packings for extended life.
  • No pulley selection or adjustment for quick, easy gas engine mounting.
  • Totally sealed housing providing independent
  • gearbox lubrication for maximum service life. Hardened steel helical design gears for smooth, quiet operation.
  • Multiple engine shaft and flange options for flexibility.
CAT Pump 8058 Direct Drive Gearbox

CAT Pump 8058 Direct Drive Gearbox

The CAT Pump 8058 Direct Drive Gearbox has the following specifications:

  • Gear Ratio ………………………… 2.0384 to 1 (2.0384 to 1)
  • Mounting Face…………………… 6-1/2″ (165 mm)
  • Engine Shaft Diameter……………………………………….. 1″ (25.4 mm)……………………………………….. 1-1/8″ ( 28.5 mm)
  • Engine Shaft Length…………… 3-1/4″ (82.6 mm)
  • Gearbox Capacity………………. 10 oz. (0.30 L)
  • Weight 8051, 8058, 8061, 8065, 8068…. 4.2 lbs. (1.90 kg) 8071, 8078 ………………………… 7.5 lbs. (3.40 kg)
  • Dimensions……………………….. 6.42 x 4.53 x8.19″ (163x115x208 mm)
  • Flow…………………………………. 5.0 GPM (19 L/M)
  • Pressure Range ………………… 100 to 2500 PSI (7 to 175 BAR)
  • Inlet Pressure Range………….. Flooded to 60 PSI (Flooded to 4 BAR)
  • Maximum Pump RPM…………. 1570 RPM (1570 RPM)
  • Maximum Engine RPM……….. 3200 RPM (3200 RPM)
  • Bore…………………………………. 0.708″ (18 mm)
  • Horsepower-Electric …………… 8.6 HP (8.6 HP)
  • Stroke ………………………………. 0.669″ (17 mm)
  • Pump Crankcase Capacity….. 25 oz. (0.75 L)
  • Weight ……………………………… 30.7 lbs. (13.9 kg)
  • Dimensions with .B…………….. 13.58 x 10.75 x 8.19″ (345 x 273 x 208 mm)
  • See Models 53, 58, 55, 51 data sheet for pump information.
CAT Pump 8085 Direct Drive Gearbox - Exploded Parts View

CAT Pump 8085 Direct Drive Gearbox - Exploded Parts View

List Price: $685.00
Our Price: $685.00
Sale Price: $600.00 Direct Drive Gearbox
You save $85.00!
Direct Drive Gearbox
Availability:: available for order
Product Code: 8058

SERVICING THE CAT Pump 8058 Direct Drive Gearbox DIS-ASSEMBLY
1. Completely drain lube from the direct drive gearbox housing.
2. Remove the four HHC screws which fasten the direct drive gearbox to the engine and separate gearbox and pump from engine.
3. Remove the four HHC screws which fasten the direct drive gearbox to the bearing cover flange and separate gearbox housing from pump.
4. Place gearbox housing on work surface with seal facing up.
5. Remove pinion oil seal by inserting screwdriver between pinion gear and inner lip of seal and pry out. Seal will be damaged and must be replaced.
6. Remove large retaining ring in groove below the pinion oil seal using retaining ring pliers and set aside for re-use.
7. Remove the pinion gear and bearing. Turn direct drive gearbox housing over onto engine mount flange surface. Bearing is pressed into position so it is necessary to press pinion and bearing out from rear. Set gearbox housing aside.
8. Remove bearing from pinion gear. Using reverse pliers remove retaining ring from groove on pinion gear and press bearing from pinion. Set aside pinion, bearing and retaining ring.
9. Remove hex machined retaining screw, lockwasher and flat holding washer from center of helical drive gear on pump shaft.
10. Slip helical drive gear from crankshaft.
11. Remove key from keyway in pump crankshaft. At this point the direct drive gearbox has been disassembled. Now begin examination of the gearbox parts for wear and reassembly. While the gearbox is in this state of disassemble, it is advisable to examine your pump for any indication of drive-end wear. If any of the following conditions are present, removal of the bearing cover flange is necessary. Only trained technicians should service drive end.
– Leakage between bearing cover flange and pump crankcase.
-Evidence of water in pump crankcase.
-Evidence of water in gearbox crankcase.
NOTE: If removal of bearing cover flange is necessary, completely drain oil from crankcase of pump.REMOVING BEARING COVER FLANGE
1. Remove the HSH screws, lockwashers and washers from bearing cover flange.
2. Tap flange with soft mallet to separate from pump crankcase.
3. Examine pump bearing and replace if worn.
4. Examine oil seal in bearing cover flange and replace if worn.
5. Examine gasket on outside of bearing cover flange and replace if cut or cracked.
6. Examine o-ring on inside outer groove of bearing cover flange and replace if cut or worn. If further pump servicing is needed, refer to your pump service manual, and Tech Bulletin 035 on “Servicing Crankcase Section”.REPLACING BEARING COVER FLANGE
1. Line up the four holes and mount gasket on outside of bearing cover flange. Note: Models 56, 59, 60 and 70 have dual bearings and eight screws.
2. Press new seal into bearing cover flange after exercising caution not to cut seal on keyway edge.
3. Line up the inside mounting holes on bearing cover flange with the holes on the pump. Keep the two outer “flanged” mounting holes to the top rear and lower front.
4. Apply Loctite-242 to the threaded area of screws before replacing. Torque per chart.REASSEMBLY of the CAT Pump 8058 Direct Drive Gearbox
1. Insert key into pump crankshaft keyway until flush with end of shaft.
2. Examine helical drive gear teeth for wear and replace if necessary. Line up keyway on gear with pump shaft keyway and key and slide onto shaft.
3. Install flat holding washer, lockwasher and retaining screw onto shaft and torque per chart.
4. Examine gearbox oil gauge and oil drain plug for any evidence of leaking and replace o-ring and gasket if necessary.
5. Examine pinion bearing for wear and replace if necessary.
6. Examine pinion gear teeth for wear and replace if necessary.
7. Press bearing over pinion gear until seated on shoulder. (Models with dual bearings; press first bearing on until seated; then second bearing until seated up to first bearing.)
8. Install retaining ring on pinion gear and snap into groove.
9. Insert pinion and gear assembly into gearbox housing and press into position until seated on shoulder. Groove for large retaining ring must be visible.
10. Insert large retaining ring into pinion bearing housing and snap into groove.
11. Lubricate I.D. and O.D. of new pinion oil seal. Place oil seal at mouth of pinion bearing housing with garter spring facing down. Carefully press seal into position until seated on retaining ring. Keep seal square in position to avoid inner lip hanging up on pinion gear edge.
12. Rotate pinion gear so keyway is up. Mount assembled gearbox housing onto pump shaft with helical drive gear. NOTE: Carefully match gear teeth and line up mounting holes. Place engine mounting flange in forward position.
13. Install the screws to fasten gearbox to bearing cover flange. Torque per chart.MOUNTING the CAT Pump 8058 Direct Drive Gearbox ONTO ENGINE
1. Rotate crankshaft of engine until keyway is at top.
2. Insert key into keyway and generously apply Loctite 76764 antiseize lubricant to engine shaft.
3. Line up keyway of pinion gear and engine shaft and carefully slip gearbox onto engine shaft until flush with engine face. Install four hex machined screws. Torque per chart. NOTE: Due to varying engine shaft lengths it may be necessary to install a small spacer on each of the four (4) hex machined screws between gearbox flange and engine face.
4. Before starting operation, fill gearbox housing to oil gauge dot with 80-90 weight gear lube and fill crankcase of pump to oil gauge dot with CAT PUMPS Special Premium Grade Non-detergent Oil.FIELD CONVERSION FROM STANDARD PUMP
To convert from a standard pump to a direct drive gearbox pump, remove the existing bearing cover, gasket and four combination head screws. Replace with new direct drive gearbox bearing cover flange, gasket, four lockwashers and new hex socket flat head screws. The bearing for the 51, 56, 58, 59 and 60 pumps is a tapered roller bearing with outer race. Remove the standard bearing cover from the pump. Remove outer race from bearing cover by gently pounding on work surface to unseat. Then use a bearing puller tool to pull race from bearing cover. Next press outer race into gearbox bearing cover flange. Be certain race is completely seated in flange before mounting onto pump.


Permanent link to this article: https://etscompany.com/wordpress/2011/09/30/cat-pump-8058-direct-drive-gearbox/

Sep 29 2011

CAT Pump 1057 – Pressure Washer Pump

Nickel Aluminum Bronze Model CAT Pump 1057

This CAT Pump 1057 Features:

  • Triplex plunger design provides smoother liquid flow.
  • V-Packings are completely lubricated and cooled by the liquid being pumped.
  • Special ported inlet manifold permits an external flush liquid providing cooling for hi-temp liquids and lubrication for low lubricity liquids.
  • Lubricated Lo-Pressure Seals provide double protection against external leakage.
  • Oil bath crankcase assures optimum lubrication.
  • Close tolerance concentricity of the ceramic plunger offers perfect alignment and maximizes seal life.
  • Precision design 304 and 316 stainless steel valves and seats are hardened and polished for ultimate seating and extended valve life.
  • Brass, Stainless Steel, Duplex SS or Nickel Aluminum Bronze manifolds for strength and corrosion resistance.
  • Special concentric, high-density, polished, solid ceramic plungers
  • provide a true wear surface and extended seal life.
  • Specially formulated, CAT PUMP exclusive, V-Packings offers unmatched performance and seal life.
  • Die cast aluminum crankcase provides high strength, minimum weight and precision tolerance control.
  • Chrome-moly crankshaft gives unmatched strength and surface hardness.
  • Oversized crankshaft bearings with greater loading capacity mean longer bearing life.
  • Wet-end easily serviced without entering crankcase.
  • Valve assemblies are accessible without disturbing piping.
  • Interchangeable inlet and discharge valve assemblies.
  • Preset seals require no packing adjustment.

CAT Pump 1057 Pressure Washer Pump Parts Breakdown PDF click here.

To get the service manual for this CAT Pump 1057 pressure washer pump click here.

CAT Pump 1057 - Pressure Washer Pump

CAT Pump 1057 - Pressure Washer Pump

This CAT Pump 1057 has the following Specifications:

  • Bore…………………………………………………………….0.945” (24 mm)
  • Stroke………………………………………………………….1.180” (30 mm)
  • Crankcase Capacity……………………………………….42 oz. (1.26 l)
  • Inlet Ports (2)…………………………………………..3/4” NPTF (3/4” NPTF)
  • Flushing Ports (2) (1051C)…………………………1/8” NPTF (1/8” NPTF)
  • Discharge Ports (2)…………………………………..1/2” NPTF (1/2” NPTF)
  • Pulley Mounting……………………………………… Either Side (Either Side)
  • Shaft Diameter………………………………………………1.181” (30 mm)
  • Weight…………………………………………………………44 lbs. (20 kg)
  • Dimensions………………………………16.28 x 12.99 x 6.44” (414 x 330 x 164 mm)
  • Flow………………………………………………………….. 10 gpm (38 l/m)
  • Pressure Range………………………………. 100 to 2200 psi (7 to 155 bar)
  • RPM……………………………………………………….. 958 RPM (958 RPM)
  • Inlet Pressure Range…………………………….. –5 to 60 psi (–0.35 to 4 bar)
  • Maximum Liquid Temperature ………………………..160°F (70°C)
  • Above 130°F call CAT PUMPS for inlet conditions and elastomer recommendations.
CAT Pump 1057 Exploded Pump Breakdown

CAT Pump 1057 Exploded Pump Breakdown

Our Price: $4,862.00
Call 1-877-824-7763 for a better price
Availability:: available for order
Product Code: 1057
CAT Pressure Washer Pump

Permanent link to this article: https://etscompany.com/wordpress/2011/09/29/cat-pump-1057-pressure-washer-pump/

Sep 28 2011

Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10

Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10

The Frame of the Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10 has  Rugged steel body · Extension cord wrap · Powder coated hood and fuel tank · Powder coated steel handles for easy lifting · 13-inch pneumatic tires · Spare parts storage system (located on back of unit) · Fuel drain plug

The Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10 has a Burner Head with : Clamped hoses · Secured photo cell · 1-piece cast aluminum · Secured fully insulated ignition connection

The Motor of the Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10 is: Heavy-duty, high quality cast aluminum enclosed electric motor

Components for the Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10 are: Built-in temperature control thermostat with control dial · High performance fan · Power switch · Secured internal components · Integral overheat and flame-out safety · Fuel gauge · Oversized fuel cap · High limit temperature shut-off · Sure start ignition for cold temperature starts · Dual connector ignitor · Error indicator read-out

The Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10 was Factory tested for multiple fuels: Kerosene, JP8/Jet A fuel, No. 1 or No. 2 fuel oil and No. 1 or No. 2 diesel fuel

For use in workshops, garages, construction sites and farms with proper ventilation.

Mi-T-M Portable Heater Kerosene Forced Air - MH-0400-0M10

Mi-T-M Portable Heater Kerosene Forced Air - MH-0400-0M10

 The Mi-T-M Portable Heater Kerosene Forced Air – MH-0400-0M10 has the following technical specifications:

  • Heat Output 400,000 BTU
  • Hot-Air Flow 1,400 CFM
  • AC Power 120 Volt/60Hz/2.8 Amp
  • Motor Size 1/2 HP
  • Air Pump Pressure 125 PSI
  • Fuel Tank Capacity 24.0 gallons
  • Fuel Consumption 3.05 gal./hr.
  • Max. Operating Hours 8.0 hours
  • Heating Area 10,000 sq ft.
  • Multi-Fuel Capable Yes
  • Net Weight 143 lbs.
  • Shipping Weight 152 lbs.
  • Length 58 in.
  • Width 30 in.
  • Height 25 in.

List Price: $2,215.00
Our Price: $1,882.75 
You save $332.25!

Availability:: available for order
Product Code: MH-0400-0M10
Mi-T-M Portable Heater

Permanent link to this article: https://etscompany.com/wordpress/2011/09/28/mi-t-m-portable-heater-kerosene-forced-air-mh-0400-0m10/